SEI FA584100TX User manual

FA584100TX
AINSLIE PORTABLE
INDOOR/OUTDOOR GEL
FIREPLACE
Assembly Instruction
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
PO:
© Southern Enterprises Inc. All Right Reserved
.
Patent N umber D653739

FA584100TX
AINSLIE PORTABLE INDOOR/OUTDOOR GEL FIREPLACE
Assembly Instruction
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage. Before beginning assembly,
separate each type of screw. Carefully study the screw diagrams below.
You may receive extra hardware with your unit.
(A) Fireplace frame
1 PC
(B) Fuel canister holder
3 PCS (C) Candle holder 1 PC
(D) Glass panel
2 PCS
(G) Left inserted handle
2 PCS
(J) Lock washer 1/4”
8 PCS
(E) Adhesive pad
4 PCS
(H) Wooden handle
2 PCS
(K) Wrench
1 PC
(F) Right inserted handle
2 PCS
(I) Screw 1/4″x13mm
8 PCS
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Do not return product to store. Please call
manufacturer for assistance, questions or
parts.

FA584100TX
AINSLIE PORTABLE INDOOR/OUTDOOR GEL FIREPLACE
Assembly Instruction
DANGER
PLEASE USE IN WELLVENTILATED AREA
The fireplace will have open flames and will generate heat.
Make sure to keep all combustible items away from the fireplace when the gel fuel is
burning.
DO NOT touch the fireplace when the gel fuel is burning.
1. Put adhesive pad (E) onto the
fireplace frame (A) as shown,
then insert glass panel (D) into
the holder as shown.
Figure 1 – Install Fireplace
A
E
D

2. Remove the fuel canister
holders (2, Figure 2) from the
fireplace and install one gel fuel
canister (1, Figure 2) into each of
the holders.
NOTICE
Make sure to remove the gel fuel
canister paper label (4, Figure 2)
before installing the canister into
the holder.
Shake the gel fuel canister before
installing it into the canister
holder.
3. Install the gel fuel holders into
the fireplace into the appropriate
mounting hole (3, Figure 3) in the
fireplace.
4. Following the instructions on
the gel fuel canister, remove the
lid (2, Figure 3) from the gel fuel
canister (1, Figure 3), and using a
long match, light the fuel in each
of the canister. Candle holder can
be used to extinguish fire.
5. Insert right inserted handle (F)
and left inserted handle (G) into
wooden handle (H). Then attach
handle to fireplace by using
screw (I) and lock washer (J) as
shown.
Figure 2 –Fuel Canister Holder and Gel Fuel Canister
Figure 3 –Fuel Canister Installed
2
1
3
Gel Fuel
4
H
F
K
I
J
123
G
A

DANGER
PROLONGED USE OF THE GEL FUEL IN THE FIREPLACE WILL CAUSE THE FIREPLACE
TO BECOME HOTAND POTENTIALLY CAN CAUSE BURNS IF TOUCHED.
DO NOT BURN MORE THAN THREE CANISTERS OF FUELAT ONE TIME.
BEFORE LIGHTING THE FUEL, MAKE SURE THAT THE PAPER LABEL IS REMOVED
FROM EACH OF THE GEL FUEL CANISTERS.
USE LONG MATCHES TO LIGHT EACH CANISTER OF FUEL.
DO NOT TOUCH THE CANISTERS WITH BARE HANDS UNTILTHE FLAME HAS BEEN
EXTINGUISHED FOR 20 MINUTES.
DO NOT BURN ANYTHING EXCEPT THE SPECIFIED CANISTERS OF GEL FUEL IN THE
FIREBOX.
KEEPCHILDRENAWAY FROM THE FIREPLACE WHEN IN USE.
KEEP FLAMABLE OBJECTS, SUCH AS CURTAINS OR DRAPERYS, AWAY FROM THE
FIREPLACE WHEN THE GEL FUEL HAS BEEN IGNITED.
MAKE SURE THE CUSTOMER DOES NOT PLACE ANY DECORATIVE ITEMS ON TOPOF
THE UNITATANYTIME.
DO NOT TOUCH THE UPPER PART OFTHE UNIT WHILE IT IS STILL IN OPERATION.
THE CANDLE HOLDER ACTS AS A COVER TO PUT OUT FIRE IF ONE WISHES TO STOP
THE FLAME.
NEVER LEAVE BURNING GEL FUEL UNATTENDED.
CARE INSTRUCTION: WIPE DOWN UNITAND CANDLE HOLDER WITH SOFT DAMP
CLOTH.
WHEN USINGTHE CANDLE HOLDER PLEASE MAKE SURE THAT THE CANNISTER
HOLDERS ARE IN PLACE.

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at [email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalo
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019