SEMPLICE SHV302 User manual

*AVAILABLE IN CHROMED BRASS; BLACK
FINISHING; POLISHED BRASS.
TECHNICAL DRAWING | MEASUREMENTS IN MM
SHEET
TECHNICAL FILES
SHV302 | T1.16BE.SB.BAD
WALL MOUNTED WASHBASIN MIXER WITH 2 HOLES, EXTERNAL PART
WITHOUT SPOUT
50
Ø7
Ø 60
4
25
Ø 41
* The dimensions might vary slightly from one finish to the other.
SHV302
- 2/8

COMPONENTS LIST | COMPONENTS DRAWING
T1.16BE.SB
01
02
03
04
05
06
SHV302
2
1
3
4
5
PLATE
PLATE O´RING
HOOD
CARTRIDGE CONCEALER
HANDLE
CLICK CLACK WASTE VALVE
6
COMPATIBLE WITH:
T1.16I
T1.675
TECHNICAL FILES
SHV302 | T1.16BE.SB.BAD
WALL MOUNTED WASHBASIN MIXER WITH 2 HOLES, EXTERNAL PART
WITHOUT SPOUT
- 2/8

ASSEMBLY INSTRUCTIONS
PICTURE 1 1- After the coating is applied and tile joints are filled in,
please remove the plastic protection covering the mixer.
MINIMUM PRESSURE 1 BAR
MAXIMUM PRESSURE 10 BAR
RECOMMENDED WORKING PRESSURE 2-5 BAR
MAXIMUM WATER TEMPERATURE 70º/176º
MAXIMUM WATER TEMPERATURE RECOMMENDED 65º/149º
MAXIMUM INLET PRESSURE DIFFERENCE (HOT-COLD) 1.5 BAR
SHV302 - 3/8
TECHNICAL FILES
SHV302 | T1.16BE.SB.BAD

1- Place the plate on the mixer body, apply silicone on the
back of the plate and fit it to the coating.
2- Screw the cartridge concealer to the locknut on the
tecaform body.
3- Place the handle onto the cartridge and verify if the rod
is in a vertical position.
ASSEMBLY INSTRUCTIONS
PICTURE 2 1- Place the hood over the tecaform body.
PICTURE 3
SHV302
TECHNICAL FILES
SHV302 | T1.16BE.SB.BAD
- 4/8

ASSEMBLY INSTRUCTIONS
PICTURE 4 1- Place the umbrak bolt inside the hole under the handle.
2- Screw it with an allen key.
END OF INSTALLATION
SHV302 -
TECHNICAL FILES
SHV302 | T1.16BE.SB.BAD
5/8

SHV302 - 6/8
1- Unscrew the handle with the help of the allen key.
2- Remove the handle from the top of the cartridge.
3- Unscrew the cartridge concealer from the tecaform locknut, then remove the hood from the
tecaform piece.
4- Unscrew the tecaform locknut with the help of a wrench. After this, you can remove the
cartridge.
To apply a new cartridge, please consider the reverse procedure.
12
3 4
CARTRIDGE REPLACEMENT
TECHNICAL FILES
SHV302 | T1.16BE.SB.BAD

We recommend regular maintenance of the tap, in order to assure its permanent good function. To clean the tap, please
use a smooth cloth with water and neutral soap. Never use products with abrasives substances, such as chloride acid,
ammonia, acetone, vinegar, bleach or abrasive sponges. The use of non-recommended products might damage
permanently the surfaces, which will annul the warranty.
WARRANTY
Waterevolution guarantees all its products in case of manufacturing defects, as follows:
5 Year Warranty:
- Machining or casting faults and porosity defects;
- Cartridge and valve defects (the wear of this component depends on water quality);
- Chrome plating or PVD defects. Defects caused by improper use are excluded, please refer to the maintenance
instructions.
2 year warranty:
- Powder Coating finishes. Defects caused by improper use are excluded, please refer to the maintenance instructions.
Our responsibility is exclusively subject to defects originated on the production process.
The warranty does not cover components subject to wear and tear, such as O-rings, gaskets, flexible hoses and joints for
connections.
ATTENTION:
Natural finishes, such as brass or stainless steel, depend entirely on the exposure to the environment and maintenance.
Therefore, any stain that may appear cannot be considered a product defect.
The warranty gives the customer the right to have all the parts which due to a manufacturing fault do not work correctly,
replaced free of charge.
The following are excluded from the warranty:
- Items or parts which are damaged or do not work properly due to negligence in the use or wrong maintenance;
- Wrong installation;
- Intervention by unqualified people or circumstances beyond one’s control.
In order to use this warranty, please keep the invoice and attach it to this document. Defective products must be sent to
Waterevolution with shipping expenses borne by the sender. This warranty document and a copy of the purchase invoice
must be attached to the package. The products will be promptly replaced and sent back with shipping expenses borne by
Pulcher Denmark.
MAINTENANCE AND WARRANTY
SHV302 - 7/8
TECHNICAL FILES
SHV302 | T1.16BE.SB.BAD