Sena HelloDevice Pro Series User manual

www.sena.com
HelloDeviceProSeries
QuickStartGuide
PS110
SetDIPSwitch&Pin-outs
Connection
Configuration
Set serial DIP switch according to your
serial device requirements(RS-232/422/485) * Please note that the power of the Pro Series should be
turned off before changing the serial communication type.
Usercanchooseoneofthefollowingprocesses
1.ConfigurationusingtheHelloDevicemanager
2.Configuration using the Hyper terminal orTelnet
3.Configuration using theWeb
Connect to host PC.Then,
slide Data/Console switch
to the Console side.
Set up the serial configuration parameters of the
terminal emulation program as follows:
DIP
Switch
Setting
RS232
(console and serial ports)
RS422
(serial ports only)
RS485
(serial ports only)
1 DCD Tx+ Tx+
2 Rx RX+ RX+
3 Tx RTS+ -
-
-
-
4 DTR CTS+
5 GND GND GND
6 DSR TX- TX-
7 RTS RTS-
8 CTS RX- RX-
DB-9
Pinouts
9 - CTS-
ON
RS-232 Mode
ON
RS-422/485 Full Mode
ON
RS-485 Half Mode
Serial
Device
Connect serial device
Insert CD
www.sena.com
Connect Ethernet cable
Connect Power supply
Data/console
9600 Baud rate/8 Data bits/None Parity/
1 Stop bits/No Hardware flow control
Copyright 1998-2005, Sena Technologies, Inc. All rights reserved.
Visit us at www.sena.com
HelloDevice Manager and User Manual are available for
download from CD or Sena website at
http://www.sena.com/support/downloads/.
For more information,refer to the user manual.

www.sena.com
HelloDeviceProSeries
QuickStartGuide
PS410
www.sena.com
SetDIPSwitch&Pin-outs
Connection
Configuration
Set serial DIP switch according to your
serial device requirements(RS-232/422/485) * Please note that the power of the Pro Series should be
turned off before changing the serial communication type.
Usercanchooseoneofthefollowingprocesses
1.ConfigurationusingtheHelloDevicemanager
2.Configuration using the Hyper terminal orTelnet
Connect the host PC and PS410's
console port using a serial console cable.
Set up the serial configuration parameters
of the terminal emulation program as follows:
DIP
Switch
Setting
RS232
(console and serial ports)
RS422
(serial ports only)
RS485
(serial ports only)
1 DCD Tx+ Tx+
2 Rx RX+ RX+
3 Tx RTS+ -
-
-
-
4 DTR CTS+
5 GND GND GND
6 DSR TX- TX-
7 RTS RTS-
8 CTS RX- RX-
DB-9
Pinouts
9 - CTS-
ON
RS-232 Mode
ON
RS-422/485 Full Mode
ON
RS-485 Half Mode
Serial
Device
Connect serial device Connect Ethernet cable Connect Power supply
3.Configuration using theWeb
Insert CD
www.sena.com
PC
9600 Baud rate/8 Data bits/None Parity/
1 Stop bits/No Hardware flow control
Copyright 1998-2005, Sena Technologies, Inc. All rights reserved.
Visit us at www.sena.com
HelloDevice Manager and User Manual are available for
download from CD or Sena website at
http://www.sena.com/support/downloads/.
For more information,refer to the user manual.

www.sena.com
HelloDeviceProSeries
QuickStartGuide
PS810
Pin-outs
Connection
Configuration
Usercanchooseoneofthefollowingprocesses
1.ConfigurationusingtheHelloDevicemanager
2.Configuration using the Hyper terminal orTelnet
Connect the host PC and PS810's
console port using a serial console cable.
Set up the serial configuration parameters
of the terminal emulation program as follows:
9600 Baud rate/8 Data bits/None Parity/
1 Stop bits/No Hardware flow control
Serial
Device
Connect serial device
3.Configuration using theWeb
Insert CD
www.sena.com
PC
Connect Ethernet cable
*Usercanchangetheserialcommunication
typeusingsoftware suchashyperterminal,
telnetorwebmanagementinterface.
RS232
(console and serial ports)
RS422
(serial ports only)
RS485
(serial ports only)
1DCD Tx+ Tx+
2Rx RX+ RX+
3Tx RTS+ -
4DTR CTS+ -
5GND GND GND
6DSR TX- TX-
7RTS RTS- -
8CTS RX RX-
DB-9
Pinouts
9 - CTS- -
Connect Power cord
Copyright 1998-2005, Sena Technologies, Inc. All rights reserved.
Visit us at www.sena.com
HelloDevice Manager and User Manual are available for
download from CD or Sena website at
http://www.sena.com/support/downloads/
For more information,refer to the user manual.