Senator SEN-405-5050K User manual

INSTRUCTION MANUAL
5-DRAWER CABINET
& SHELVED WORKBENCH
ORDER CODE:
SEN-405-5050K
• Cold roll steel body
• Powder coated resin paint
• Durable, high quality finish
• 38mm wooden worktop
• Smooth action drawer slides
• 1350(W) x 500(D) x 850mm(H)
QUALITY GUARANTEE & WARRANTY
SE ATOR TOOLS carry a one year manufacturer’s warranty.
SE ATOR TOOLS are designed & manufactured
to the highest standards & specifications.
Assuring the quality and performance required by all sectors of industry.
SE ATOR TOOLS are fully guaranteed against
faulty materials & workmanship.
Should they be found to be defective, they will either be repaired or replaced free of
charge (fair wear and tear and/or misuse excepted).
Please retain supplier invoice as proof of purchase.
THE ENVIRONMENT
Always dispose of unwanted tools, accessories and packaging materials in an environmentally
friendly manner.
© The Kennedy Group Ltd. 07/18
THE KE EDY GROUP, WIGSTO . LEICESTER, E GLA D, LE18 2FS.
Senator is a registered trade mark of The Kennedy Group Ltd.

2 7
NOTES

SENATOR
Cabinet & Work Bench are designed to help you work safely and efficiently. Lifting
equipment can be dangerous if the correct operating and maintenance procedures are not followed.
Operating instructions and basic safety procedures are as follows:
LOADI G:
lDo not load the top drawer first.
lDo not drop tools into the drawers.
lDo not completely fill only one drawer.
lDo not load a drawer from the front.
BOX CONTENTS
6 3
USE:
lDo not open more than one loaded drawer at a time,
as this may cause the cabinet to become unstable.
lDo not stand on this product.
lDo not slam the drawers shut.
OPQRS
Lock Washers
(40+3)
Hex Nuts
(40+3)
Adjustable
Leg Levellers
(4)
ST4 8 x 16
Screws
(40+3)
A— Side anels (2) B— Brace Supports (4) C— Centre Supports (2)
F— Back Wall anel (2) G— Drawer Stops (2) H— Shelves (2) I— Corner Braces (4)
J— Drawers (5) L— Female Slides 2 (10) M— Male Slides (10) — Wooden Work Top (1)
K— Female Slide 1 (10)
D/E — Drawer Housing anels (2)
FRO T
REAR
REAR
Step 9:
Attach male drawer slides (M). ush in male
slide until spring mechanism rides over
formed spring stop.
Step 10:
Finally, fit the drawer units (J). Fix the female
drawer slides (K) to the side of each drawer
(J). Slide rear tab into slot, then locate centre
and front tabs in an upward movement.
If necessary tap the slides into position using
a suitable hammer.
To fit drawer into cabinet unit, mate male and
female slides, pushing back into unit until
spring tips engage stops.
THIS CABI ET IS OT I TE DED TO BE USED FOR STA DI G O .
MAINTENANCE
lKeep the drawer slider mechanism lubricated. Lubrication should be carried out at least twice
a year.
lKeep the wooden work surface clean and dry and do not use a hammer or other heavy tool directly on
the work surface.
lThe maximum weight for each drawer should not exceed 25kg. The maximum weight to which the
cabinet is subjected should not exceed 180kg, including the worktop load.
Hex Head
Screws
(4)

ASSEMBLY INSTRUCTIONS
To assemble this product you will require a crosspoint No. 2 screwdriver, a 10mm combination ratchet
spanner and a drill with 4mm wood bit. If available, a 10mm socket wrench may aid access when
assembling the unit.
4 5
Step 1:
Join the two side panels (A) at the bottom of
the cabinet using two brace supports (B). Fix
using 8 bolt, nut and washer combinations (O,
and Q). Make sure that the brace supports
have the edge with the two bolt holes facing
upwards.
Step 2:
Attach centre supports (C) to the cross brace
supports (B) just fitted using the bolt, washer
and hex nut combinations (O, and Q).
Step 5:
Attach the drawer-side back panel (F) and
drawer stops (G). ush the bolt through the
back panel and the drawer stop before fixing to
the side panel and the drawer housing. Fix the
shelf-side back panel using the bolt, nut and
washer combinations (O, and Q).
Step 6:
Insert shelves (H) in position inside the cabinet
and fix using the usual bolt, washer and nut
combinations (O, and Q).
Step 7:
Fix the triangular corner braces (I) at the front
and rear of the cabinet, bolting them to the
bottom brace supports and the side panels.
Fit the adjustable leg levellers (R) to the
bottom of the side panels (A).
Step 8:
lace the work top on a suitable surface and
turn the cabinet upside down on top of it.
osition the cabinet centrally on the work top
and mark the screw holes through the fixing
holes in the top supports. Remove the cabinet
and drill four 4mm x 13mm deep holes to
receive the four 10mm x 16mm hex head
screws used to secure the work top to the
cabinet. Make sure that the holes do not
exceed 13mm deep. Tighten the hex head
screws using a suitable wrench.
Step 3:
Slide in drawer slider housings D - left hand,
front facing (i.e. two rows of holes to the front
of the cabinet) and E - right hand, front facing
(i.e. two rows of holes to the front of the
cabinet). Fix at front of cabinet only using 4 x
M6 bolt, lock washer and hex nut
combinations (O, and Q).
Bolt drawer housing panel to the side panel
and the centre support using the usual fittings.
Do not fix at the rear of the cabinet at this
time, as a back panel and the drawer stops
have to be bolted through the drawer housing
(as in Step 5).
Attach female drawer slides (L) to the drawer
housing panels (D and E). Slide rear tab into
slot, then locate centre and front tabs in a
downward movement. If necessary tap the
slides into position using a suitable hammer.
Step 4:
Fix the two top cross brace supports (B) at the
top end of the cabinet using the bolt, washer
and nut combinations provided.