Sencor SCA BA88 User manual
SCA BA88
Pre-calibrated
sensor module USER´S MANUAL
EN – 2
Content
1 – Remove old sensor
2 – Install new sensor
3 – User device reset (no need to use it in case of new sensor)
1. Remove old sensor module
1.1 Slide the power switch to “OFF” position (red)
1.2 Remove the bottom cover
1.3 Remove the plastic fuse
EN – 3
1.4 Remove sensor module
2 Install a new sensor module
2.1 Put the sensor module into the compartment and push it to top position
EN – 4
2.2 install the plastic fuse to fix the sensor module
2.3 install the cover to the device
2.4 Finish: Slede the power switch to “ON” position (Green)
EN – 5
3. User device reset
1) Turn the device on. ALCO message will be shown.
2) In this mode, press and hold the up and down arrow button and then add the ON/OFF
button. After afew seconds of holding these buttons down, the screen below will be
shown.
3) Using the up button, change the first number to 1, see figure below and wait.
The number of measurements performed since the last reset will be shown.
4) Then, hold down the ON/OFF for 3 seconds and the instrument will be reset.
The device will automatically return to the initial screen and you can continue to use it.
EN – 6
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
MATERIALS
Dispose of packaging material at a public waste disposal site.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES
The meaning of the symbol on the product, its accessory or packaging indicates
that this product shall not be treated as household waste. Please, dispose of this
product at your applicable collection point for the recycling of electrical & electronic
equipment waste. Alternatively in some states of the European Union or other
European states you may return your products to your local retailer when buying
an equivalent new product. The correct disposal of this product will help save
valuable natural resources and help in preventing the potential negative impact
on the environment and human health, which could be caused as a result of
improper liquidation of waste. Please ask your local authorities or the nearest waste
collection centre for further details. The improper disposal of this type of waste may
fall subject to national regulations for fines.
For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the necessary
information from your seller or supplier.
Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information about the
correct disposal method from local government departments or from your seller.
This product meets all the basic EU regulation requirements that relate to it.
Changes to the text, design and technical specifications may occur without prior notice
and we reserve the right to make these changes.
The original version is in the Czech language.
Address of the manufacturer:
FAST ČR, a.s., Černokostelecká 1621, Říčany CZ-251 01
EN – 7
EN Warranty conditions
Warranty card is not apart of the device packaging.
This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty
is limited to the following conditions. Warranty is referred only to the customer goods using for common
domestic use. The claim for service can be applied either at dealer’sshop where the product was bought,
or at below mentioned authorized service shops. The end-user is obligated to set up aclaim immediately
when the defects appeared but only till the end of warranty period. The end user is obligated to cooperate
to certify the claiming defects. Only completed and clean (according to hygienic standards) product will
be accepted. In case of eligible warranty claim the warranty period will be prolonged by the period from
the date of claim application till the date of taking over the product by end-user, or the date the end-user
is obligated to take it over. To obtain the service under this warranty, end-user is obligated to certify his
claim with duly completed following documents: receipt, certificate of warranty, certificate of installation.
This warranty is void especially if apply as follows:
ēDefects which were put on sale.
ēWear-out or damage caused by common use.
ēThe product was damaged by unprofessional or wrong installation, used in contrary to the applicable
instruction manual, used in contrary to legal enactment and common process of use or used for another
purpose which has been designed for.
ēThe product was damaged by uncared-for or insufficient maintenance.
ēThe product was damaged by dirt, accident of force majeure (natural disaster, fire, and flood).
ēDefects on functionality caused by low duality of signal, electromagnetic field interference etc.
ēThe product was mechanically damaged (e.g. broken button, fall).
ēDamage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable
working conditions (e.g. high temperatures, high humidity, quakes).
ēRepair, modification or other failure action to the product by unauthorized person.
ēEnd-user did not prove enough his right to claim (time and place of purchase).
ēData on presented documents differs from data on products.
ēCases when the claiming product cannot be indentified according to the presented documents (e.g. the
serial number or the warranty seal has been damaged).
Authorized service centers
Visit www.sencor.eu for detailed information about authorized service centers.
Designed in Europe by Sencor®, Made in China
Table of contents
