SENKO SENKO-20 User manual

- 1 -
SENKO Auto Open Heat Press Manual
Model NO.: SENKO-20/30
CONTENTS
I. Assembly Drawing -----------------------------------------------------------------------------------1
II. Technical Parameters ------------------------------------------------------------------------------2
III. Operation Process -------------------------------------------------------------------------------3-4
IV. Maintenance ------------------------------------------------------------------------------------------5
V. Trouble Shooting For Transfer Print Quality------------------------------------------------5
VI. Circuit Diagram -------------------------------------------------------------------------------------6
VII. Explosion View ----------------------------------------------------------------------------------7-8

- 2 -
I. Assembly Drawing
○
1Power Switch
○
2Emergency Stop Button
○
3Digital Controller
○
4Pressure Adjuster
○
5Handle Bar Grip
○
6Draw-out Handle
○
7Electromagnet
○
8Electromagnet Suck Plate
○
9Support Shaft
II. Technical Parameters
1. Model No.: SENKO-20/30
2. Machine Dimensions: 950*750*450mm
3. Printable Articles Max Size: 400*500*30mm
4. Voltage: 220V/1Phase;120V/1Phase
5. Power for machine: 20’’x32’’ platen:220V/2.0KW; 120V/1.8KW
16’’x20’ platen: 220V/1.8KW; 120V/1.75KW;
Power for heating tube: 1.8KW*1
6. Recommend Setting: 30~280s; 180~210°C
Time Range: 0~999s
7. Packing size: 105*85*55cm

- 3 -
III. Operating Process
GY-04 Operation Instruction
1. When you turn on the heat press machine, the display shows “OFF”.
2. Press the “OK”button will show the degrees Celsius “C”. You could use the Up or Down button to switch
between degrees Celsius and degrees Fahrenheit.
3. Press “OK ”button to enter TEMPERATURE setting. When the TEMP indicator blinks, use Up/Down
button to set the required temperature. (Temperature adjustable range: 100-225 C/212-437 F)
4. Press“OK”button to enter TIME setting. When the TIME indicator blinks, use Up/Down button to set the
required time. (Time adjustable range: 0-999S)

- 4 -
5. After finishing above-mentioned settings, press “OK ”button to enter the heating mode. If the
temperature is below 100C/212F, then the display reads “LO”(low temperature).
6. If you need to adjust the settings during the heating mode, you could repeat step 2 to step 5 to do the
adjustment.
7. When the heat platen has settled into its desired temperature, press down the heat platen, then the
timer will automatically start counting down and CD-L indicator blinks. The timer will begin to sound once it
reaches 3 seconds. The warning is meant to prepare the user to release the handle once the time reaches 0
seconds. When the handle is lifted, the timer will automatically sound off.
8. Long press the digital controller for 4-5 seconds, then can enter the engineering model:
P-5: Temperature Difference Calibration Mode, calibration range is -99 to +99
P-6: Intermittent heating in advance before setting, setting range is from 1 to 20 Sec.
This function is to set the heating time and pause time after the machine enter the constant temperature
mode. The setting parameters is different according to different size of heat platen.
P-7: Constant temperature in advance before setting, setting range is from 1 to 9 degree.
This function is to set when the machine will enter the constant temperature mode. You could set a
temperature value that you want to enter to constant temperature before it reach the setting temperature.
For example, the setting temperature is 180℃and P-7 is 10℃, then when the temperature reaches 170℃,
it will enter the constant temperature mode, heating and pause in cycle to avoid overheat.
P-8: Constant temperature mode, when reach the setting temperature, the machine will stop heating for 1
seconds then will keep heating for few seconds, setting range is from 0 to 9 Sec.
P-9: Countdown mode: “No”means when the machine work, it will count down, “Yes”means when reach the
setting temperature, the machine will enter the countdown mode.

- 5 -
IV. Maintenance
1. In order to prolong the machine service life, please add the lubrication oil on the joints regularly .
2. Turn off the power before changing spare parts. In order to ensure the accuracy of the parameter of
GY-04 controller. please re-set the time and temperature
3. To avoid damage, please keep the heaters well when change the spare parts
V. Trouble Shooting For Transfer Print Quality
1. After changing heat platen, time and temperature showing become abnormal:
Solution: Reset time/temperature according to the manual
2. If the color is not as bright as photo after printing, please try below ways:
Solution: A. Adding transfer time. B. Increasing transfer temperature.
3. If the print color is too brown or the transfer paper is almost burnt:
Solution: Please reduce the setting temperature
4.If print color is different/ partial transfer effect is not good enough:
Solution: A. Increase the pressure. B. Extend the transfer time. C. Change the sublimation paper.
5.If the machine is getting abnormal, please contact us to solve the problems.

- 6 -
VI. Circuit Diagram

- 7 -
VII. Explosion View

- 8 -
Serial No.
Part Name
Qty
1
Machine Foot
2
2
Machine Frame
2
3
Slide Rail Connection Plate-Left
1
4
Slide Rail Connection Plate-Right
1
5
Draw-out Handle
1
6
Front Plate
1
7
Adapter Plate
1
8
Adapter Plate
1
9
Plate Connector
1
10
Plate Connector
1
11
Fixing Part
1
12
Connecting Shaft
1
13
Connection Part
2
14
Slide Rail
2
15
Hexagon Socket Head Cap Screw
26
16
Gasket
30
17
Back Cover
1
18
Electrical Parts Bracket
1
19
Digital Controller
1
20
Connecting Spindle
1
21
Gas Spring Fitting
2
22
Pressure Adjust Knob
1
23
Gas Spring
2
Serial No.
Part Name
24
Under Plate
1
25
400x500 Heat Platen
1
26
400x500 Heat Platen Cover
1
27
Anti-scald Protect Cover
1
28
Electromagnet
1
29
Davit Arm
1
30
Adapter Plate
1
31
Connecting Shaft
1
32
Pressure Adjuster Spindle
1
33
Connecting Piece
2
34
Inserted Pin
1
35
Handle Bar Grip
1
36
Handle Frame
2
37
Serpentuator
1
38
Serpentuator Connector
2
39
Solid State Relay
1
40
Transformer
1
41
Electromagnet Driver Board
1
42
Power Switch
1
43
Fuse
1
44
Power Cord
1