Sennheiser HME 43-K User manual

Instructions for use
HME 43-K
TitelSeite.fm Seite 1 Dienstag, 11. Juli 2006 4:46 16

TitelSeite.fm Seite 2 Dienstag, 11. Juli 2006 4:46 16



쐃

AB
D
E


F
C
UB_INT.fm Seite 1 Dienstag, 11. Juli 2006 4:52 16

H
I J
G
K
UB_INT.fm Seite 2 Dienstag, 11. Juli 2006 4:52 16

1
The HME 43-K headset
The HME 43-K is a closed pilot’s headset with a noise-
compensating microphone, designed for use in jet aircraft.
The HME 43-K features an ultra-lightweight design with
excellent ergonomic properties, replaceable leatherette
earpads and a double-sided, adjustable padded headband.
The leatherette earpads are extremely comfortable.
The HME 43-K headset has two separate connectors – one
for the microphone and one for the headphones. The
microphone can be worn on either the left or right-hand
side and ensures excellent speech transmission.
Delivery includes
Delivery of the HME 43-K includes:
A1 Headset with earcups , microphone boom 
and headband 
1 Cable clip
1Carryingbag
2Foamearpads
1 Wind screen

2
Safety instructions
• Please read these instructions carefully and completely
before using the headset.
• Make these instructions easily accessible to all users at
all times. Always include these instructions when
passing the headset on to third parties.
• Never repair or attempt to repair a defective headset
yourself. Contact your local Sennheiser agent or the
Sennheiser Service Department.
• Protect the headset from humidity and dust.
Intended use of the headset
Intended use includes:
• having read these instructions especially the chapter
“Safety instructions”.
• using the headset in jet aircraft and within the
operating conditions as described in these instructions.
Improper use
Improper use means use of the headset other than as
described in these instructions or when you use it under
operating conditions which differ from those described in
these instructions.

3
Putting the headset into operation
Connecting the headset
Connect the 1/4“ (6.35 mm) stereo jack plug (PJ 055) for
the headphones and the
PJ 068 jack plug (5.25 mm) for the
microphone to the corresponding jack sockets of your
intercom.
Wearing the headset
The letters refer to the diagrams on the cover page.
BAdjust the length of the headband to fit your head size
or shape. The earpads should exert a slight pressure on
the ears.
C
Holding the headset with two hands, carefully bend the
headband to adjust it to a snug but comfortable fit
.
DPut the headset on.
ETurn the microphone boom towards the mouth.
FBend the flexible microphone boom so that the
microphone is placed at the corner of the mouth.
Maintain a distance of approx. 1 cm between micro-
phone and mouth.
GAffix the headset cable to the clothing by means of the
supplied cable clip. Attach the cable clip so that you can
move your head freely.

4
Adjusting the volume
Adjust the volume directly on the intercom.
Adjusting the microphone sensitivity
HThe microphone sensitivity has been factory pre-set. If
necessary, you can change the microphone sensitivity
by turning a small screwdriver in the direction of the
arrow.
High volume!
This headset is capable of producing high
sound pressure levels. Higher volumes or
longer durations can damage your hearing!
Set the volume to a medium level. Make sure
that you can hear critical sounds such as
warning alarms.
ATTENTION!

5
Care and maintenance
Cleaning the headset
Use a soft, slightly damp cloth to clean the headset from
time to time. If necessary, the headset can be cleaned with
soapy water (use a mild cleanser such as a detergent).
Replacing the earpads
For reasons of hygiene, the earpads should be replaced
from time to time.
IGrasp the edge of the foam earpad behind the earcup
and peel it up and away from the earcup. Slide the new
earpad onto the earcup. Repeat for the other earcup.
Water can damage the electronics of the unit!
Water entering the housing of the headset can
cause a short-circuit and damage the
electronics.
Only use a slightly damp cloth to clean the
headset. Do not use any solvents or cleansing
agents.
ATTENTION!

6
Replacing the wind screen
If the wind screen shows signs of wear such as tears or
holes, replace the wind screen.
JPull the wind screen from the microphone. Gently slide-
on the new wind screen and ensure that it fits securely
over the microphone.
Storage and transportation
KTurn the microphone into the position shown on the
diagram. Rotate the earcups by 90°.
Use the supplied carrying bag for storage and
transportation.
If problems occur ...
Problem Possible cause Possible solution
You cannot
communicate
via the
intercom.
The microphone
connection has been
pulled out.
Check if the microphone
jack plug is connected
correctly.
The microphone
sensitivity is
adjusted too low.
Increase the microphone
sensitivity (see “Adjusting
the microphone
sensitivity” on page 4).