Senquip ORB-X1-G User manual

ORB-X1 Quick Start Guide
ORB-X1
Mounting brackets
Mounting screws
Gland inserts
Allen key
1. What is in the Box?
If using GSM and the
ORB does not contain
an internal SIM, insert
a SIM card, note the
orientation carefully.
3. Insert SIM Card
Apply power to
pin 1 and ground
to pin 2 of the
header or insert 4
x AA batteries.
The green light
will go on and
orange light will
flash.
4. Apply Power
5. Enter Setup Mode
Press the setup
button to enter
setup mode and
activate the ORB
webserver. The
green light will
flash.
Use a phone or tablet to connect
to the ORB’s Wi-Fi using the SSID
and Wi-FI password located
under the lid.
Using a web-browser, go to
192.168.4.1. Enter username
“admin” and the ORB’s setup
password to access the ORB’s
webserver.
6. Connect to the Webserver
Configure Wi-Fi or
GSM connectivity
using the Network
tab. Save settings.
If using GSM, set
the correct APN for
your SIM.
Close the lid to exit
setup mode.
7. Configure the ORB
Create an
account on the
Senquip Portal
(portal.senquip.
com) to view
data and
configure your
ORB.
8. Access your Data
Using the 3mm Allen
key provided, loosen
the 6 cover screws
ensuring that all 6
screws have ejected
before opening.
2. Open the ORB
7. LED Status Guide
The image on left shows the
ORB brackets in the wall
mount position; to pole
mount rotate the brackets
by 180 degrees. To wall
mount, remove the brackets
and screw directly into the
ORB mount points.
8. Mounting the ORB
STATUS
NETWORK
Meaning
Off Off
Device is sleeping
Flash (1Hz) Off
Setup Mode
On Flash (1Hz)
No internet connection
On On
Internet connection
Fast Flash Fast Flash
Factory Reset
Off Fast Flash
Firmware Update
Slow Flash
Off
Pre
-charge mode

USE OF THE PRODUCTS
You agree, represent, warrant and undertake to Senquip Pty Ltd (Senquip) that prior to ordering the product supplied by Senquip
pursuant to this agreement, you obtained all relevant information relating to the product ordered; ensured that information was
current; assessed the product, and ensured that it is fit for the purpose for which it is intended to be used.
Products are not authorised for use in critical safety or other applications where a failure may reasonably be expected to result in
personal injury, loss of life, or catastrophic property damage.
If a customer uses or sells the products for use in any such applications, the customer acknowledges that such use or sale is at the
customer's sole risk. The customer will indemnify, defend or hold Senquip and their electronic component suppliers/assemblers
harmless from and against any and all liabilities and costs arising out of or in connection with the use of the product or sale.
The products sold hereunder and any other products sold by Senquip have been subject to limited testing and should not be used in
conjunction with mission-critical equipment or applications. Any performance specifications are believed to be reliable but are not
verified, and the Buyer must conduct and complete all performance and other testing of the products, alone and together with, or
installed in, any end-products.
The Buyer shall not rely on any data and performance specifications or parameters provided by Senquip. Senquip does not suggest or
make any recommendation as to the accuracy of measured data in any particular application in which the Buyer may use the product.
Parameter values stated or implied in any documentation are for explanation only and should not be taken as typical or representative
of a real world situation.
It is the Buyer’s responsibility to independently determine suitability of any products and to test and verify the same. The information
provided by Senquip hereunder is provided “as is, where is” and with all faults, and the entire risk associated with such information is
entirely with the Buyer.
Senquip products and information brochures change from time to time in response to product development and customer demand, to
ensure products are up to the highest and most recent standards and technological developments. Please ensure that a product
ordered from Senquip is the latest version of that particular product prior to placing an order, by contacting Senquip or an authorised
reseller.
Senquip will not be held liable for the failure of others:
a. Senquip will attempt to ensure you receive GNSS, satellite, GSM and WiFi communication with third-party devices/systems,
Internet, AWS, and/or other related services if required, however these services are not controlled by Senquip.
b. Senquip is not liable for any loss, damage or liability associated with the loss, interruption or lack of GNSS, GSM, Wi-Fi coverage,
Internet, connectivity to AWS, connectivity to a third-party system or device and/or other related services.
c. Sensor failure or incompatibility.
FORCE MAJEURE:
Senquip is not liable for any loss, damage or liability associated with:
a. the acts of Government;
b. atmospheric and heliospheric events;
c. military actions, including war and terrorism;
d. floods, storms, earthquakes or other natural occurrences; or,
e. late deliveries due to the courier / postal networks;
f. events beyond the control of Senquip.
WARRANTY AGAINST DEFECTS POLICY & PROCEDURES
Senquip warrants the goods against defects in factory workmanship and materials within the warranty period.
The warranty period for products shall be 12 months from the date of invoice. The warranty period for repaired items shall be 90 days
from the date of invoice.
The customer must notify the point of purchase / distributor of any defect coming within the provisions of this warranty, within 30 days
of the fault occurring. A copy of the relevant invoice or the relevant invoice number as proof of the date of purchase must be provided
with returned goods. Senquip is not liable for any loss or damage you suffer or liability you incur arising out of the use of any Senquip
products. Senquip Pty Ltd liability is limited to:
a. repair of a defective product; or
b. if a product supplied by Senquip cannot be repaired, Senquip will replace a defective product with the same product.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
To and where Australian Law permits, products / goods determined by Senquip to have been abused, misused, altered, neglected, lost,
or damaged in shipment are not covered by the warranty.
Subject to Australian Consumer Legislation taking precedence, the warranty will be null and void in the following circumstances and all
expenses incurred are the responsibility of the purchaser:
a. The goods / products have been opened by a third party.
b. The goods / products have been contaminated by oil, water, grease, acid, subject to impact, fitted in excessive vibration
environments or corrosive environments or improperly connected.
c. The goods / products have been tampered with or an attempt to repair it has been made by any company or individual before
notification of a claim to Senquip For further information please contact us below:
CONTACT DETAILS
E-mail: [e-mail]
Website: www.senquip.com