Sense-Tech KIMAX 2 User manual

KIMAX 2 Wireless
Instruction manual

2
Table of contents
Kimax 2 Wireless........................................................................................................ 3
Daily use .................................................................................................................... 3
Displayed menus ........................................................................................................ 3
Menu structure ........................................................................................................... 4
Troubleshooting ......................................................................................................... 5
Technical specifications.............................................................................................. 6
Notes.......................................................................................................................... 7
Warranty
Kimax 2 Wireless is covered by Sense-Tech Weighing Systems ApS guarantee. Electronic
failure and broken components caused by normal use are repaired or exchanged when
necessary, when sent to the factory.
Damage to your vehicle caused by installation of Kimax instruments or loss of time caused by
recalibration or repairs of Kimax instruments are not covered by Sense-tech Weighing Systems
ApS in any case.

3
Kimax 2 Wireless
Daily use
When you switch on your Kimax 2 Wireless (it is done by pressing for approx. 1 sec.) you
will be able to view all the weight readings from your Kimax 2 unit in a distance of up to 100 m
under ideal conditions.
All you have to do is to pair your Kimax 2 unit with your Kimax 2 Wireless and it is easily done.
Refer to the Id settings on the following page.
The Kimax 2 Radio/Universal is broadcasting the measured actual axle loads, payloads and
total weights every 3 seconds through a 433.92 MHz transmitter.
Displayed menus
When you turn on your wireless terminal, it starts up at
the same display position as it was showing when
powering down from the former use.
Until a valid reading is received, it displays #. - - . -
The individual weight for channel #1 is displayed as
1.04.5, where the first digit is the display position, the
next 3 digits is formatted as xx.x tons
When a channel is not in use, the read out is displayed as
#.00.0 (If the readout on the Kimax 2 Radio/Universal is
0.00 the display of the Kimax 2 Wireless will also be
reading 0.00).
Your wireless terminal has to be coded with exactly the
same Id number as the actual Kimax 2 unit you want to
monitor.

4
Menu structure
1.xx.x Channel 1
2.xx.x Channel 2
3.xx.x Channel 3
4.xx.x Channel 4
5.xx.x Channel 5
6.xx.x Channel 6
7.xx.x Channel 7
8.xx.x Channel 8
9.xx.x Load (Truck)
A.xx.x Load (Trailer)
b.xx.x Total (Truck)
c.xx.x Total (Trailer)
d.xx.x Load (Truck+Trailer)
E.xx.x Total (Truck+Trailer)
> 1 second
Turn on by pressing
I .xxx Id
Increase Id
> 6 seconds
Decrease Id
Run mode
Store Id
> 2 seconds
Run mode
Id settings
Valid Id setting is 001 –999.
Make sure the Id number on the
Kimax 2 Wireless matches the Id
number on your Kimax 2 Radio or
Kimax 2 Universal.

5
Troubleshooting
Problem
Possible solution
Poor range..
Please make sure that the antenna from the Kimax 2 Radio
or Kimax 2 Universal is not bended or placed near a sturdy
steel surface.
The display shows only #.--.-
Please check the id setting on both the Kimax 2 Wireless
and the Kimax 2 Radio or Kimax 2 Universal.
Make sure they match.
Display stays blank..
Check battery supply
If you do not succeed in solving the problem with the text above, feel free to contact us.

6
Technical specifications
Supply voltage
2 x 1.5 V AA battery
Display
Four-digits 7-segment LCD, character height 12.7 mm
Device bus
433.92 MHz FM
Range
0 - 100 m
No. of individual ID codes
999
Operating temperature
-10 °C...+50 °C
Storage temperature
-25 °C...+50 °C
Dimensions
200 x 95 x 35 mm
Weight
approx. 230 g
The policy of Sense-Tech Weighing Systems ApS is to continually improve our products.
This means that product specifications may change without prior notice.
Set 060000-0105 includes:
Kimax 2 Wireless
Part number 060000-01
1 x Dashboard bracket
2 x 1.5 V AA battery
Find additional technical information on www.kimax.com.

7
Notes
Vehicle id
Kimax 2 Radio/Universal id
Kimax 2 Wireless id

Sense-Tech Weighing Systems ApS ● Bygade 43 A ● DK 7173 Vonge ● Tel [phone] ● Fax [phone]
[e-mail] ● www.sense-tech.com
MANU_90008_003