SenTech STC-MBS510U3V Installation instructions

No.15S103-01
2/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
!
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
For U.S.A.
Warning:
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Safety / Product Precautions
Product Precautions
Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling or
storage could damage the camera.
Do not pull or damage the camera cable.
During camera use, do not wrap the unit in any material. This will cause the internal temperature of the
unit to increase.
Do not expose the camera to moisture, or do not try to operate it in wet areas.
Do not operate the camera beyond its temperature, humidity and power source ratings.
While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the sensor or filter area and scratching or damaging this area.
Do not keep the camera under the following conditions:
In wet, moist, and high humidity areas
Under hot direct sunlight
In high temperature areas
Near an object that releases a strong magnetic or electric field
Areas with strong vibrations
Apply the power that satisfies the requirements specified in this document to the camera.
Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not
scratch the surface of the glass.
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
!
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
For U.S.A.
Warning:
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
!
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
For U.S.A.
Warning:
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.

No.15S103-01
3/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
The camera is a general-purpose electronic device; using the camera for the equipment that may threaten
human life or cause dangers to human bodies directly in case of failure or malfunction of the camera is
not guaranteed. Use the camera for special purposes at your own risk.
Defect pixels may appear due to the sensor characteristics.
During camera use, do not plug or unplug other USB devices (USB storage, etc.). Plugging or unplugging
other devices may result in a failure to recognize the USB camera.
Increasing gain level may increase the noise level.
When the camera is in Long Exposure mode, the noise level may increase.

No.15S103-01
4/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
Contents
1OVERVIEW............................................................................................................ 8
1.1 Features ....................................................................................................................................... 8
1.2 Item Numbers Naming Method...................................................................................................8
2SPECIFICATIONS ................................................................................................. 9
2.1 Electronic Specifications............................................................................................................9
2.1.1 STC-MBS510U3V / STC-MCS510U3V.................................................................................................... 9
2.1.2 STC-MBS322U3V / STC-MCS322U3V.................................................................................................. 13
2.2 Spectral Sensitivity Characteristics ........................................................................................ 17
2.2.1 STC-MBS510U3V ................................................................................................................................. 17
2.2.2 STC-MCS510U3V (without IR cut filter).............................................................................................. 17
2.2.3 STC-MBS322U3V ................................................................................................................................. 18
2.2.4 STC-MCS322U3V (without IR cut filter).............................................................................................. 18
2.3 Mechanical Specifications........................................................................................................ 19
2.3.1 STC-MBS510U3V / STC-MCS510U3V.................................................................................................. 19
2.3.2 STC-MBS322U3V / STC-MCS322U3V.................................................................................................. 19
2.4 Environmental Specifications.................................................................................................. 20
2.4.1 STC-MBS510U3V / STC-MCS510U3V.................................................................................................. 20
2.4.2 STC-MBS322U3V / STC-MCS322U3V.................................................................................................. 20
2.5 External connector.................................................................................................................... 21
2.5.1 USB 3.0 micro B................................................................................................................................... 21
2.5.2 IO Connector........................................................................................................................................ 22
2.5.3 Reference Input Circuit ....................................................................................................................... 23
2.5.4 Reference Output Circuit .................................................................................................................... 25
3DIMENSIONS ...................................................................................................... 27
3.1 STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V....................... 27
4SENSOR INFORMATION .................................................................................... 28
4.1 Pixel Transferring Image........................................................................................................... 28
5IMAGE ACQUISITION AND CAMERA OPERATIONAL MODES........................ 29
5.1 Freerun....................................................................................................................................... 29
5.2 Trigger Mode.............................................................................................................................. 30
5.2.1 Frame Start Trigger (Edge Preset)...................................................................................................... 31

No.15S103-01
5/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
5.2.2 Frame Start Trigger (Pulse Width Trigger) ......................................................................................... 32
5.2.3 Exposure Start Trigger, Exposure End Trigger.................................................................................. 33
5.2.4 Trigger Software .................................................................................................................................. 33
6IO FUNCTION...................................................................................................... 34
6.1 Input Port Function ................................................................................................................... 34
6.1.1 Trigger Input......................................................................................................................................... 34
6.1.2 Line Status........................................................................................................................................... 34
6.1.3 Line Debouncer.................................................................................................................................... 35
6.1.4 Trigger Delay........................................................................................................................................ 35
6.2 Output Port Function ................................................................................................................ 36
6.2.1 Line Source.......................................................................................................................................... 36
6.2.1 User Output.......................................................................................................................................... 38
6.2.2 Line Status........................................................................................................................................... 38
6.2.3 Output signal duration setting and Pulse width setting.................................................................... 38
6.3 Hardware Reset......................................................................................................................... 38
7CAMERA OPERATION........................................................................................ 39
7.1 ROI (Region of Interest)............................................................................................................ 39
7.1.1 ROI (One Region)................................................................................................................................. 39
7.1.2 Multi ROI............................................................................................................................................... 41
7.2 Pixel Format............................................................................................................................... 43
7.3 Binning....................................................................................................................................... 43
7.4 Decimation................................................................................................................................. 44
7.5 Image Flip .................................................................................................................................. 45
7.6 Gain ............................................................................................................................................ 47
7.6.1 Analog Gain ......................................................................................................................................... 47
7.6.2 Digital Gain........................................................................................................................................... 47
7.6.3 White Balance Gain (Only available for the color cameras) ............................................................. 47
7.7 Black Level................................................................................................................................. 48
7.8 ALC (Auto Light Control).......................................................................................................... 49
7.8.1 ALC Control Method............................................................................................................................ 49
7.8.2 AGC (Auto Gain Control)..................................................................................................................... 49
7.8.3 Auto Exposure..................................................................................................................................... 49
7.8.4 The procedure of ALC ......................................................................................................................... 50
7.9 White Balance (Only available for the color cameras)........................................................... 51

No.15S103-01
6/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
7.9.1 White balance control methods.......................................................................................................... 51
7.9.2 Disable.................................................................................................................................................. 51
7.9.3 Manual (Off).......................................................................................................................................... 51
7.9.4 Auto White Balance (Continuous) ...................................................................................................... 51
7.9.5 Push to Set White Balance (Once)...................................................................................................... 51
7.10 Gamma Table............................................................................................................................. 52
7.11 Save and load the camera setting data ................................................................................... 53
7.11.1 Saving the Camera Settings................................................................................................................ 53
7.11.2 The Camera Settings Loading ............................................................................................................ 54
7.11.3 The Camera Settings Loading When the Camera Power is on......................................................... 54
7.11.4 The Camera Settings Initialization...................................................................................................... 54
7.12 Pixel Defect Correction............................................................................................................. 55
7.13 Trigger........................................................................................................................................ 55
7.13.1 Trigger Signal Process........................................................................................................................ 55
7.14 Device User ID........................................................................................................................... 56
7.15 Event Control (Only USB3 Vision protocol)............................................................................ 56
7.15.1 The way to use Event .......................................................................................................................... 56
7.15.2 Event Function..................................................................................................................................... 56
7.16 Chunk Control (Only USB3 Vision protocol)........................................................................... 57
7.16.1 The way to use Chunk......................................................................................................................... 57
7.16.2 Chunk Data........................................................................................................................................... 57
7.17 GenICam command list ............................................................................................................ 58
7.17.1 DeviceControl ...................................................................................................................................... 58
7.17.2 ImageFormatControl............................................................................................................................ 59
7.17.3 AcquisitionControl .............................................................................................................................. 60
7.17.4 TransportLayerControl........................................................................................................................ 60
7.17.5 DigitalIOControl................................................................................................................................... 60
7.17.6 CounterAndTimerControl.................................................................................................................... 61
7.17.7 EventControl........................................................................................................................................ 61
7.17.8 EventExposureEndData ...................................................................................................................... 61
7.17.9 EventExposureStartData..................................................................................................................... 61
7.17.10 EventTestData................................................................................................................................. 61
7.17.11 AnalogControl................................................................................................................................. 62
7.17.12 LUTControl...................................................................................................................................... 62
7.17.13 UserSetControl................................................................................................................................ 62
7.17.14 ChunkDataControl .......................................................................................................................... 62
7.17.15 TestControl...................................................................................................................................... 63
8REVISION HISTORY ........................................................................................... 64

No.15S103-01
7/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide

No.15S103-01
8/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
1 Overview
This document describes the specification of the following cameras.
STC-MCS510U3V / STC-MBS510U3V
STC-MCS322U3V / STC-MBS322U3V
1.1 Features
・USB3 Vision
・Frame Rate (Full Scan) : 75.7 FPS @5 MP 8bit, 121 FPS @3.2M 8bit
・CMOS Global Shutter
・Up to 64 Pixel Defect Correction (Default: ON)
・8bit,10bit, 12bit output
1.2 Item Numbers Naming Method
Below is a description of the camera naming method:
STC-MxS510U3V
Figure 1: Naming Method
510: 5.1M Pixel, 2/3”Sensor
322: 3.2M Pixel, 1/1.8”Sensor
C: Color
B: Monochrome
Sensor Manufacturer
S: Sony
U3V: USB3 Vision

No.15S103-01
9/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
2 Specifications
2.1 Electronic Specifications

No.15S103-01
10/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
Model Number
STC-MBS510U3V
STC-MCS510U3V
Image Sensor
2/3” 5.1M Progressive
Monochrome CMOS（Sony:IMX250LLR-C）
2/3”5.1M Progressive
Color CMOS（Sony: IMX250LQR-C）
Shutter Type
Global
Active Picture Elements
2448 (H) x 2048 (V)
Cell Size
3.45 (H) x 3.45 (V) µm
Sync System
Free run, External trigger(Hardware, Software)
Maximum
Frame
Rate
(Full
Scan)
8bit output
75.7 fps
10bit output
37.6 fps
10bit Packed output
58.3 fps
12bit output
37.6 fps
12bit Packed output
50.9 fps
ADC bit width
10bit / 12bit
Video Format
8/10/12 bit output
(Support packed on 10bit, 12bit)
8/10/12 bit output
(Support packed on 10bit, 12bit)
Noise
Level
8bit output
≤ 3 LSBs (Gain 0 dB)
10bit / 10bitPacked
output
≤ 12 LSBs (Gain 0 dB)
12bit / 12bitPacked
output
≤ 48 LSBs (Gain 0 dB)
Sensitivity
550 Lux
1240 Lux
Exposure
time
8bit output
20.1μseconds to 26 seconds
10bit output
26.5μseconds to 53 seconds
10bit Packed output
22.0μseconds to 34 seconds
12bit output
26.5μseconds to 53 seconds
12bit Packed output
23.2μseconds to 39 seconds
Gain
Analog Gain
0 to 24 dB
Digital Gain
0 to 6 dB
Black
Level
8bit output
0 to 31
10bit / 10bitPacked
output
0 to 127
12bit / 12bitPacked
output
0 to 511
White Balance Gain
N/A
-40dB to 12dB
ROI (AOI)
Horizontal: 64 to 2448 (2432 on Packed) / Vertical: 32 to 2048
Adjustable Steps for offset:
16 pixels in horizontal direction (64 pixels on Packed) / 4 lines in vertical direction
Adjustable Steps for offset: 4 pixels in horizontal direction / 4 lines in vertical direction
Multi ROI
16 Regions (Horizontal 4 regions x Vertical 4 regions)
Gamma
Gamma Table =0.1 to 4.0
Binning
Individual x2 Horizontal, Vertical Binning
(Horizontal: Average, Vertical: Addition)
N/A
Decimation
Individual x2 Horizontal, Vertical Decimation
Image Flip
Horizontal / Vertical / Horizontal and Vertical / OFF
Pixel Defect Correction
Up to 64 points
Auto
Image
Control
Auto Exposure
Support
Support
Auto Gain
Support
Support
Auto White Balance
N/A
Support
Operational Mode
Free-run / Edge-preset Trigger / Pulse width Trigger / Start Stop Trigger
User Setting Storage
Support
Communication
Via USB3.0 bus

No.15S103-01
11/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
Interface
USB3.0 Super speed (USB3.0 Micro B)
Protocol
USB3 Vision® 1.0.1, GenICam Standard Version (SFNC 2.2, PFNC 2.0) compliant
and Sentech’s unique protocol (on Normal SDK, Trigger SDK)
Input / Output
Three GPIO, One Camera Hardware Reset
Power
Input Voltage
+5V(typ.) (This conforms to the USB standard)
Consumption
Less than 4.2 W

No.15S103-01
12/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide

No.15S103-01
13/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide

No.15S103-01
14/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
Model Number
STC-MBS322U3V
STC-MCS322U3V
Image Sensor
1/1.8” 3.2M Progressive
Monochrome CMOS（Sony: IMX252LLR-C）
1/1.8” 3.2M Progressive
Color CMOS（Sony: IMX252LQR-C）
Shutter Type
Global
Active Picture Elements
2048 (H) x 1536 (V)
Cell Size
3.45 (H) x 3.45 (V) µm
Sync System
Free run, External trigger(Hardware, Software)
Maximum
Frame
Rate
(Full
Scan)
8bit output
121.0 fps
10bit output
60.5 fps
10bit Packed output
91.6 fps
12bit output
60.5 fps
12bit Packed output
80.2 fps
ADC bit width
10bit / 12bit
Video Format
8/10/12 bit output
(Support packed on 10bit, 12bit)
8/10/12 bit output
(Support packed on 10bit, 12bit)
Noise
Level
8bit output
≤ 3 LSBs (Gain 0 dB)
10bit / 10bitPacked
output
≤ 12 LSBs (Gain 0 dB)
12bit / 12bitPacked
output
≤ 48 LSBs (Gain 0 dB)
Sensitivity
550 Lux
1240 Lux
Exposure
time
8bit output
19.0μseconds to 22 seconds
10bit output
24.3μseconds to 44 seconds
10bit Packed output
20.7μseconds to 29 seconds
12bit output
24.3μseconds to 44 seconds
12bit Packed output
21.7μseconds to 33 seconds
Gain
Analog Gain
0 to 24 dB
Digital Gain
0 to 6 dB
Black
Level
8bit output
0 to 31
10bit / 10bitPacked
output
0 to 127
12bit / 12bitPacked
output
0 to 511
White Balance Gain
N/A
-40dB to 12dB
ROI (AOI)
Horizontal: 64 to 2048 / Vertical: 32 to1536
Adjustable Steps for offset:
16 pixels in horizontal direction (64 pixels on Packed) / 4 lines in vertical direction
Adjustable Steps for offset: 4 pixels in horizontal direction / 4 lines in vertical direction
Multi ROI
16 Regions (Horizontal 4 regions x Vertical 4 regions)
Gamma
Gamma Table =0.1 to 4.0
Binning
Individual x2 Horizontal, Vertical Binning
(Horizontal: Average, Vertical:Addition)
N/A
Decimation
Individual x2 Horizontal, Vertical Decimation
Image Flip
Horizontal / Vertical / Horizontal and Vertical / OFF
Pixel Defect Correction
Up to 64 points
Auto
Image
Control
Auto Exposure
Support
Support
Auto Gain
Support
Support
Auto White Balance
N/A
Support
Operational Mode
Free-run / Edge-preset Trigger / Pulse width Trigger / Start Stop Trigger
User Setting Storage
Support
Communication
Via USB3.0 bus

No.15S103-01
15/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
Interface
USB3.0 Super speed (USB3.0 Micro B)
Protocol
USB3 Vision® 1.0 , GenICam Standard Version (SFNC 2.2, PFNC 2.0) compliant
and Sentech’s unique protocol (on Normal SDK, Trigger SDK)
Input / Output
Three GPIO, One Camera Hardware Reset
Power
Input Voltage
+5V(typ.) (This conforms to the USB standard)
Consumption
Less than 4.2 W

No.15S103-01
16/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
Precautions
*1 The procedure used to measure Sensitivity is as follows:
Measure the luminance when white level achieved 100% on F5.6
*2 Please refer to section ROI for further details on the ROI.
*3 Binning & Decimation cannot work simultaneously.
*4 The Binning & Decimation units do not change.
*5 The user should not input the trigger more frequently than the maximum frame rate.
If the trigger was input during the sensor ReadOut timing, ReadOut will be interrupted. This trigger will cause the
exposure to end.
*6 Start/Stop trigger mode is only available for the software trigger.
*7 When using this camera with a USB 2.0 port, the user should take precautions in regards to power consumption
due to this camera operating on the USB 3.0 standard.
How to obtain full frame rate
This general guideline may help the user obtain the full frame rate from the camera.
To obtain the full frame rate, the data transfer speed on the USB bus depends on the capability of the host
controller.
Renesas / Fresco Logic‘s host controller improved the data transfer speed drastically in the second generation.
Intel’s chipset increased the transfer speed 10% to 20%.
When PCIExpress board of USB3.0 interface is used, please insert the PCIExpress Gen2.0(5.0[GT/s]) slot. If non-
PCIExpress Gen2.0(5.0[GT/s]) is used, data transfer speed could decrease by about 50%.
If an incapable host controller causes a lower frame rate, the camera frame rate should be set lower than the
maximum to adjust for the incapable host controller spec. This may resolve the issue.
Due to the huge data transfer, PC resources may be consumed during the process. If this occurs, the frame rate
of the camera may be effected.
Camera Setting
Environment
Parameter
Setting
Parameter
Setting
Gain Up
0 db
Light Source
Light Box(White)
AGC
OFF
Color temperature
5100K
White Balance
Optimum
Exposure Time
1/30
Electrical Shutter
1/30
F on Lens
Ｆ5.6
Black Level
Optimum
Target Luminance
Illuminometer
Gamma
Factory Setting

No.15S103-01
17/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
2.2 Spectral Sensitivity Characteristics
TBD

No.15S103-01
18/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
TBD

No.15S103-01
19/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
2.3 Mechanical Specifications
Model Number
STC-MBS510U3V
STC-MCS510U3V
Dimensions
C Mount: 28 (W) x 28 (H) x 40 (D) mm (*1)
Optical Filter
No IR Cut Filter
IR Cut Filter
Optical Center Accuracy
Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 1.5 deg.°
Material
Aluminum alloy
Lens Mount
C Mount
Interface Connectors
USB Connector: USB3.0 Micro B type
I/O Connector: HR10A-7R-6PB (Hirose) or equivalent
Weight
Approx. 48g
(*1) excluding the connectors
Model Number
STC-MBS322U3V
STC-MCS322U3V
Dimensions
C Mount: 28 (W) x 28 (H) x 40 (D) mm (*1)
Optical Filter
No IR Cut Filter
No IR Cut Filter
Optical Center Accuracy
Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 1.5 deg.°
Material
Aluminum alloy
Lens Mount
C Mount
Interface Connectors
USB Connector: USB3.0 Micro B type
I/O Connector: HR10A-7R-6PB (Hirose) or equivalent
Weight
Approx. 48g
(*1) excluding the connectors

No.15S103-01
20/65
STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V
Specifications and Use’s guide
2.4 Environmental Specifications
Model Number
STC-MBS510U3V / STC-MCS510U3V
Operational
Temperature
Minimum
Environmental Temperature: 0 deg. ºC
Maximum
Camera housing temperature (top plate) shall not exceed 55 deg. ºC （*1）
Storage Temperature
Environmental Temperature: -30 to +65 deg. C, Environmental Humidity: 0 to 85%
Vibration
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, XYZ 3 directions 30 min. each
Shock
Acceleration 38G, half amplitude 6ms, XYZ 3 directions 3 times each
Standard Compliancy
EMS: EN61000-6-2, EMI: EN55011
RoHS
RoHS Compliant
Model Number
STC-MBS322U3V / STC-MCS322U3V
Operational
Temperature
Minimum
Environmental Temperature: 0 deg. ºC
Maximum
Camera housing temperature (top plate) shall not exceed 55 deg. ºC （*1）
Storage Temperature
Environmental Temperature: -30 to +65 deg. C, Environmental Humidity: 0 to 85%
Vibration
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, XYZ 3 directions 30 min. each
Shock
Acceleration 38G, half amplitude 6ms, XYZ 3 directions 3 times each
Standard Compliancy
EMS: EN61000-6-2, EMI: EN55011
RoHS
RoHS Compliant
*1: Please insure the camera is installed with the appropriate heat dissipation. If camera has a mounted lens and a tripod
with an aluminum plate, this could decrease the camera housing temperature for heat dissipation. When the internal
temperature sensor on the camera shows less than 65 ºC, the camera housing temperature (top plate) will be less than 55
ºC.
Upper side of camera
Measuring point