SENTRY GUARDING SYSTEM 600 GUARDING User manual




Patented Design
AS/NZS
4024.3610
STRENGTH
TESTED
EASY
INSTALLATION
MODULAR
SYSTEM
COST SAVING
UP TO 30% A PRODUCT OF
Safety & General

This Installation Manual is provided as an assembly guide for the Sentry Guarding System. Refer to the
Design Guide for recommended layouts for various job site conditions. The product may be unstable
during installation until fully assembled. Proper safety measures must be taken at all times. Product may
fail and void warranty if installation does not comply with standards, design guide and drawings.
Sentry Guarding System has been designed and tested to comply with:
AS/NZS 4024.3610 - Safety of Machinery - Conveyors.

• 17mmringspanner
• RiveterBlindnutKit(M10)
• RivetGun
• 6mmHexKey

• SafetyGlasses
• ProtectiveGloves
• SafetyFootware


InstallM10RivetnutusingBlindnutRiveter.

TightenmildsteelshoulderboltM10x12x50LG/
StainlessSteelshoulderbolt(PartNo:SGS10-12-50SS)
to44.7Nmusinghexkey.
Note:MildSteelshoulderboltshouldbehotdip
galvanisedinplacewithpost.



90°layout
180°layout
T-layout
Singlelayout
 

Engageallbrackethooks
ontowiremeshBand
swingbrackettoalign
withthesideofthemesh
panel.

Securemeshlockingtabs
using6.4stainlesssteel
rivets(Ø4.8mm,6.4mm
grip).

Slidetoptaboflatch
assemblybetweenwire
meshandbracket.
Locatefrontwasheron
frontfaceandsecurewith
6.4stainlesssteelrivets.

ScrewM10boltwith
springwasher,halfway
intolatchassembly.

Insertallfourmesh
lockingtabsintoallocated
slots.


Widthmayvaryforeachdesign.Werecommendallpanelstobeunder20kgforaonemanoperation.
AllGuardingwithaweightof15kgorovershouldhaveaweightindicationsigninstalled.
600
900
1200


Ensurelatchbolthasbeen
undonetounlockingposition
andlatchismovingfreely.
Hookbottomend
slotsofGuardingonto
shoulderboltandswing
toengagelatch.


Hooktopendslotsof
Guardingontoshoulder
boltandswingto
engagelatch.

LockGuardingsbytightening
theM10lockingboltto44.7Nm.
RefertoOperationofLockingMechanism.

Suite 1, 2 Ambitious Link, Bibra Lake, WA 6163
[phone] [phone] [email protected]
ABN 79 060 988 767
.com.au
AS/NZS
4024.3610
STRENGTH
TESTED
EASY
INSTALLATION
MODULAR
SYSTEM
COST SAVING
UP TO 30% A PRODUCT OF

Identicationplatescanbettedtotheside
bracketandsecuredwith6.4steelrivets
(Ø4.8mm,6.4mmgrip).
20
90
70 Ø5mm
Scan for additional
information


Oncethelatchhasbeen
engagedwiththeshoulderbolt,
theGuardingPanelissecured.
Useaspannertotightenthe
M10boltto44.7Nmtolockthe
GuardingPanel.

UseaspannertoundoM10boltabout
halfwayforeachsidebracketsto
un-lockthelatchassembly.
Whilepressingthelatcharm,swing
Guardingpaneloutandreleaselatch
arm.Allowtheexternallatchgroove
(shownbelow)torestontotheshoulder
boltforeasypanelremoval.
Groove