SEON vMax Live User manual
vMax™ Live
Installation Guide
Document Part Number: 700-0097 R001
2
700-0097 R001
Thank you for purchasing the Seon vMax™ Live tracking device.
vMax Live remains the most technologically advanced hard-wired
GPS tracking device on the market, providing location updates every
10 seconds.
This truly LIVE tracking method enables vMax Live to perform under a
wide variety of applications, allowing it to excel in eet management in
many markets. The applications for vMax Live are limited only by the
human imagination.
Options for the vMax Live GPS tracking unit include the adaptability that
comes with the optional set up of four input and four output options. The
inputs and outputs require a standard 12-volt relay, available from any
auto parts store. It is recommended that you run the wiring directly from
the battery. It is also recommended that you acquire the assistance of a
certied mechanic to ensure that the wiring is connected correctly.
At Seon, we go to extremes to deliver a world-class product. Live
support is embedded directly into our tracking system. If you encounter
difculties, have additional questions, or simply want to say “job well
done,” we’re always delighted to hear from you. Given proper care, your
vMax Live device will provide reliable service for years to come. Thank
you for choosing Seon. We appreciate your business.
Introduction
Figure 1: GPS Tracking Device
3
700-0097 R001
Figure 2: vMax™ Live Wiring Diagram
4
700-0097 R001
Installation of your vMax™ Live vehicle tracking device is as easy as it
gets – just follow these three easy steps:
1. Plug the two antenna cables and wiring harness into the transceiver
unit, and then place the antenna (with the white text facing UP) on your
dash at the base of the windshield. Run the cables along the side of the
dash at the door hinge, and place the transceiver box under your dash.
For best results, consider using a zip-tie or double-sided tape to secure
the transceiver to ensure it doesn’t fall from beneath the dash.
2. On the wiring harness, connect the RED wire to a constant 12-volt
power line. Connect the BLACK wire to the frame ground. Connect that
BROWN wire to a 12-volt accessory power source (one which only has
power when the ignition is on). It’s that simple!
3. The device is now installed. For a more covert installation, you may
place the antenna under the dash, all the way up near the base of the
windshield, secretly out of sight. Our antennae can see through foam,
glass, and berglass, but it cannot see through metal. For this reason,
it is important that the unit be placed with no metal or wiring between it
and the sky.
The four outputs allow you to have remote controlled access to lock and
un-lock the doors, honk the horn, and similar aspects that permit ease in
control of the vehicles that have vMax Live.
The four inputs allow vMax Live to send information back to the server.
These services can be set up so you can fully utilize your new unit.
Installation
PIN Harness Wire Color Description
1 BLACK GND
2 YELLOW RELAY 2 OUTPUT (-)
3 GREEN RELAY 3 OUTPUT (-)
4 ORANGE RELAY 4 OUTPUT (-)
5 BLUE SWITCH 3 INPUT (-)
6 NOT USED
7 NOT USED
8 RED +8 TO +16V INPUT (CONSTANT)
9 RED (BUNDLE) BACKUP BATTERY INPUT
(12V LEAD-ACID TYPE)
10 BLACK GND
11 WHITE SWITCH 2 INPUT (-)
12 GRAY SPEAKER OUTPUT (+)
13 RED/WHITE SWITCH 4 INPUT (-)
14 BLUE (BUNDLE) MICROPHONE INPUT (+)
15 BROWN IGNITION INPUT (+)
16 WHITE/BROWN RELAY 1 OUTPUT (-)
17 BLACK SPEAKER/MIC SIGNAL GND
18 GREEN/YELLOW SWITCH 1 INPUT (-)
19 PURPLE LED OUTPUT (20Ma MAX)
20 A/D INPUT (0-16V)
Figure 3: Wiring Harness Description
Other SEON GPS manuals
