Severtson Cinema Series User manual
Instruction Manual for
Cinema & Tension Deluxe Series Electric
MODELS: GE43***, GE169***, GE1610***, GT43***, GT169***, GT1610***
Thank you for purchasing a Severtson projection screen. Before use, please read the instructions
carefully. After installation, store the instructions for future reference.
Rev 191205
Instruction Manual for Cinema & Tension Deluxe Series Electric
Overview
Parts Included
1
Instruction Manual for Cinema & Tension Deluxe Series Electric
Installation Instructions
Take out all the parts from the packaging and verify that all the parts have been included, then
follow the steps below to install the screen.
Note 1.1: When installing the projection screen it is important to choose the correct fasteners
for the ceiling type. Choosing the wrong fasteners can lead to severe injuries or screen damage.
1. Remove any shipping tape or screws that are holding the weight bar.
2. Determine the desired mounting method and follow the correct procedure for installing
the mounting brackets (see Table 1.1 below). Make sure the brackets are level before
securing them in place. For hanging by wire installation, see Note 1.2.
Table 1.1
Mounting Method
Screw Placement
Instructions
Wood Framed Wall
Using four wood screws
(5x40mm) for each bracket,
secure each bracket to the wall.
Make sure that the screws
penetrate into the studs of the
framed wall, otherwise the
brackets will not be securely
fastened.
Wood Framed Ceiling
Using four wood screws
(5x40mm) for each bracket,
secure each bracket to the
ceiling. Make sure that the screws
penetrate into the studs of the
ceiling, otherwise the brackets
will not be securely fastened.
Concrete Wall
Use an electric drill to drill four
holes for each bracket and
hammer the provided tapping
anchors into each hole. Secure
the brackets onto the wall by
fastening the tapping screws
(5x40mm) to the tapping
anchors.
2
Instruction Manual for Cinema & Tension Deluxe Series Electric
Concrete Ceiling
Use an electric drill to drill four
holes for each bracket and
hammer the provided tapping
anchors into each hole. Secure
the brackets onto the ceiling by
fastening the tapping screws
(5x40mm) to the tapping
anchors.
Note 1.2: To mount the screen to the ceiling by hanging wire, attach the wire-hanging
attachments to the standard mounting brackets using the included screws (M5x10). The wire
can now be strung through the additional loops in the brackets (see images below).
3. In preparation to put the screen on the brackets, loosen the fixing screw on each bracket to
lower the baffle. Make sure any shipping tape or screws have been removed from the
weight bar.
3
Instruction Manual for Cinema & Tension Deluxe Series Electric
4. Now place the screen on the baffle hooks making sure they latch onto the screen casing.
Then tighten the fixing screws on the bottom of each bracket to lock the screen onto the
brackets.
5. The screen should now be securely mounted to your installation surface.
4
Instruction Manual for Cinema & Tension Deluxe Series Electric
Controlling the Screen
There are many different options included to control the projection screen. Only connect the
screen to the options that will be used.
RS-232 Pinouts
Note 1.1: When the screen is set to manual control, only manual control of the screen will work.
For any other type of control set the screen to remote control.
1. Manual Control. The push-button located on the left end of the screen face near where the
projection screen extends. Pushing the button will cause the motor to switch between
several different modes. The state change pattern can be seen in the diagram below:
5
Instruction Manual for Cinema & Tension Deluxe Series Electric
1. Trigger Connection. The trigger jack recognizes outputs of DC 5V-12V. When power is
sensed the screen will automatically lower. When power is off the screen will rise back into
the case.
2. IR Remote. The remote control will work up to 25’ from the IR eye and an angle of up to 30°.
The remote will not work if the signal or receiver is covered. Keep the remote away from
high temperatures and humidity. Change the battery when the signal is low.
3. RS-232. Home automation systems that are compatible with RS-232 communication can
remotely operate the screen via the RJ-45 connector on the left-side control panel.
6
Instruction Manual for Cinema & Tension Deluxe Series Electric
Appendix A: Adjusting the Screen Limits
We only recommend that experience AV installers adjust the motor limits of the projection screen.
The upper limit should never be adjusted - it controls the point at which the screen stops
retracting into the case and is factory-set to flush. Improperly adjusting the limits of the motor will
cause damage to the screen and motor and will void all warranty. Severtson Screens is not
responsible for any damage caused by adjusting limits for any reason.
Always make small adjustments and test before continuing.
Limit adjustment controls may vary. It is the responsibility of the installer to verify drop
and retraction limit controls.
1. Remove the small rubber stopper on the underside of the screen case near the left-side of
the case and extend the screen enough to be able to locate the limit controls inside the
screen case.
2. Identify the upper (retraction) and lower (drop) limit switches and then adjust the
appropriate limit according to the respective steps below. In some cases, the drop and
retraction limit screws may be reversed, so it is crucial that small adjustments be made to
verify the correct screw is being adjusted.
3. To adjust the up limit (this should usually not be adjusted since it is factory-set):
a. Bring the screen to the down position.
7
Instruction Manual for Cinema & Tension Deluxe Series Electric
b. Press “up” on the remote control.
c. If the screen does not fully ascend into the case use the accessory tool to adjust the
up limit. Turn the Up limit towards the “+” symbol until the screen is at the desired
position.
d. If the screen ascends too far then simply turn the same positioning screw towards
the “-“.
4. To adjust the down limit:
Make sure to test the screen between each small adjustment.
a. Bring the screen to the up position.
b. Press “down” on the remote control.
c. If the screen does not fully drop to your desired position from the case use the
accessory tool to adjust the down limit. Turn the Down limit towards the “+” symbol
until the screen is at the desired position.
d. If the screen drops too far then simply turn the same positioning screw towards the
“-“.
8
Instruction Manual for Cinema & Tension Deluxe Series Electric
Appendix B: Adjusting the Screen Tension
This section is only for applicable models (tab-tensioned models beginning with “GT”). The tension of
the screen may need to be adjusted occasionally if the screen begins to appear wavy.
1. To increase string tension, rotate the knob clockwise; to decrease string tension, rotate the
knob counter-clockwise until desired tension is reached.
9
Instruction Manual for Cinema & Tension Deluxe Series Electric
Appendix C: Troubleshooting the Screen
The Cinema Series and Tension Deluxe Series screens are designed for many years of use.
Problems are usually simple to resolve and caused by small issues or improper end use. If
problems persist, please contact us.
General Troubleshooting:
Screen does not retract.
Power cable is not connected or outlet does not have power.
Check the connection of the power cable.
Screen goes too low or does not
go down enough.
Adjust the lower limit as described in Appendix A: Adjusting the Screen
Limits.
Screen goes too far into case or
does not ascend to the correct
position.
Adjust the upper limit as described in Appendix A: Adjusting the Screen
Limits.
IR control does not work.
Check the batteries in the IR remote.
Check to make sure you are in the IR range.
Close windows or shut off lights that may be diffusing the IR signal.
10
Instruction Manual for Cinema & Tension Deluxe Series Electric
Warnings
1. Do not attempt to take apart or modify the screen. If any problems occur please contact
your local dealer.
2. The screen is designed to be transported, stored, and operated in the horizontal position.
Do not stand the screen up on its end vertically for any extended period of time.
3. Do not clean the screen case with water - only dust the screen to avoid electric shock.
4. Make sure the brackets used are firmly secured to the wall or ceiling to avoid any damage.
5. Make sure fixing screws are tight to avoid any damage.
6. When installing electric motors use a professional or contact your local dealer. Incorrect
connection of wires may result in leaks or fires.
7. Fluorescent lights may cause interference with infrared signal.
8. Be careful not to scratch or damage the screen surface while handling it.
9. Do not write or draw on screen surface. Do not poke, fold, or tear screen material.
10. Never attempt to clean a coated screen with soap or water. If cleaning is necessary, use a
damp cloth and dab the affected area lightly. A cotton cloth can be used to gently wipe dust
off of the screen.
11. Do not use detergents or harsh chemicals to clean screen material. A soft cloth and mild
soap can clean dust and dirt off a non-coated screen material. A cotton cloth can be used
to gently wipe dust off of the screen.
12. Retract the screen after each use.
13. To prevent unnecessary damage, the assembly and maintenance of the screen should be
done by adults.
11
This manual suits for next models
7
Table of contents
Other Severtson Projection Screen manuals
Severtson
Severtson GE169 SERIES User manual
Severtson
Severtson Pro Frame X Series User manual
Severtson
Severtson Spirit Series User manual
Severtson
Severtson DF169 Series User manual
Severtson
Severtson GP169 series User manual
Severtson
Severtson TF43 Series User manual
Severtson
Severtson Deluxe Curved CF235 Series User manual
Severtson
Severtson Whisper Series User manual
Popular Projection Screen manuals by other brands
Elite Screens
Elite Screens Spectrum Series user guide
Elite Screens
Elite Screens Insta-DEM Screen Series user guide
Beamax
Beamax HOME CINEMA MODULES Q Series user manual
Draper
Draper Targa Installation & operating instructions
DreamScreen
DreamScreen 628-092 Series installation instructions
SI
SI 7 SERIES FIXED owner's manual
Strong MDI
Strong MDI Monarch installation manual
Screen Innovations
Screen Innovations 1 SERIES FIXED owner's manual
SI
SI 7 SERIES FIXED owner's manual
Da-Lite
Da-Lite Contour Electrol Instruction book
EliteProAV
EliteProAV EDGE FREE Pro Frame Thin UST Series user guide
KICK ASS
KICK ASS KAODCMFS84 user guide
