DreamScreen 628-092 Series User manual

INSTALLATION
INSTRUCTIONS
DREAMSCREEN TAB

2
GENERAL INFORMATION
For-
mat Model Size View Area (WxH)
Border Height
H1
Length
L1
Bottom
Shaft
Length
L2
Assemble
Distance L3 Package Volume GW
(Kg)
B1 B2 B3 min max PL PW PH
16:9
628/629-X-092 92” 2032×1143 600 60 60 1941 2544 2328 1944 2424 2840 220 180 22,0
628/629-X-100 100” 2214×1245 600 60 60 2043 2721 2505 2121 2601 2990 220 180 25,0
628/629-X-106 106” 2347×1320 500 60 60 2018 2854 2638 2254 2734 3180 220 180 26,0
628/629-X-109 109” 2413×1357 500 60 60 2055 2920 2704 2320 2800 3246 220 180 26,5
628/629-X-120 120” 2657×1494 400 60 60 2092 3164 2948 2564 3044 3500 220 180 27,5
628/629-X-129 129” 2856×1606 400 60 60 2204 3363 3147 2963 3243 3699 220 180 28,0
628/629-X-138 138” 3055×1719 300 60 60 2217 3522 3306 3122 3402 3898 220 180 29,0
628/629-X-150 150” 3321×1868 300 60 60 2366 3788 3572 3388 3668 4110 220 180 40,0
PRESSURE MARKS IN THE FABRIC
The fabric might endure some pressure during transport and storage. Most of any visible pressure marks
on the fabric will straighten out after a while, but if some remain please carefully use a hand-held steamer to
straightening them out.
Please make sure the fabric is never exposed to heat from ovens, sunlight etc. as this may damage
the screen-fabric.
Measured by mm.

3
REMOVING THE TRANSPORTATION SECURITY BRACKETS
WARNING!
If these brackets are not removed upon use, the screen will be severely damaged!
INSTALLATION
Parts list
Item Qty
Screen 1PCS
IR Remote Control 1PCS
RF Remote Control 1PCS
Wall Control 1PCS
Wireless Trigger 1PCS
Screws 4PCS
Self-Tapping Screw
and Rubber Plug 8PCS
L-Bracket 2PCS
Hook 2PCS
Adjustment Tool 1PCS
Instruction 1PCS

4
RECOMMENDED MOUNTING POSITION

5
FLUSH CEILING INSTALLATION
First, draw up a horizontal line to make sure the screen is correctly lined up. Then install the two ceiling
brackets to the ceiling and distance them about 15cm from each corner of the cassette. Place the cassette
onto the brackets and secure it by tightening the screw at the bottom.
WALL INSTALLATION
First, draw up a horizontal line to make sure the screen is correctly lined up. Then install the two wall
brackets to the wall and distance them about 15cm from each corner of the cassette. Place the cassette onto
the brackets and secure it by tightening the screw at the bottom.

HOOK WIRE CEILING INSTALLATION
Install the cassette to the ceiling using the included rings. Attach to hooks or a suited wire.
Move the rings to a suited position.
Attach the cassette to the hook or wire.
Secure the position of the ring.
1
3
2
6

7
BASIC CONTROLS: IR REMOTE
& WALL CONTROL
The V6 Tab includes both a manual wall control (wired)
and a regular IR remote. The IR remote can be used for
learning your universal remote or control system the codes
for easy system integration. The remote is setup from factory
and does not require additional pairing.
CONTROLS
Stop Button
RS232 serial port settings
Baud rate 2400
Data bit 8
Parity N
Stop bit 1
Default HEX code RS232
FF 10 11 00 DD UP
FF 10 11 00 EE DOWN
FF 10 11 00 CC STOP
RS232 SERIAL PORT CONTROL
(OPTIONAL)

PAIRING THE RF REMOTE
The RF remote control has been set up at the factory and should work right away. If this is not the case, you
will need to use the learn function to program the remote. Remove the back cover of the remote control to
reveal the learning button as shown below. Connect the power cable and listen for 1 beep from the motor.
When you hear the beep, point the remote at the screen and press the learning button twice followed by the
up button. The remote is now paired to the screen.
UP
STOP
DOWN
RESETTING THE RF REMOTE CONTROL
To reset the RF remote control, open the back case of the RF Remote congtrol and follow the sequence of
pressing buttons: learn button->stop button->learn button. After 3 beeps, the code is deleted. Follow the
steps above to reconnect the remote.
LEARNING BUTTON
8

PAIRING THE IR REMOTE CONTROL (OPTIONAL)
The IR remote control has been set up at the factory and should work right away. If this is not the case, please
contact your dealer to get a replacement remote. Make sure the remote is pointing the IR window at the left
side of screen housing.
12V WIRELESS TRIGGER (OPTIONAL)
LEARNING BUTTON
UP
STOP
DOWN
The wireless trigger has been set up at the factory and should work right away, however if this is not the case
you will need to use the learn function.
Open the back case of the remote control. Then press the Learning Button twice and you will hear Di..Di sound.
At this time, press the Learn Hole in the wireless trigger. When you hear the Di..Di sound, wireless trigger is
paired to the screen.
LEARNING HOLE
9

ADJUSTING THE DROP
WARNING! Adjusting the drop may damage your screen if not done correctly. Please use MICRO steps when
adjusting and TEST the adjusted screen-drop by pushing the UP and DOWN remote-buttons frequently to
make sure the adjustments have been made correctly. If you see no movement, please reset the dial back to
the exact same location as originally and call your dealer. Please use ONLY the DOWN dial, the UP dial is only
used for setting the upper stop which is already adjusted correctly at the factory. If the UP dial is adjusted, the
tensionbar might be retracted into the cassette and thus damaging the entire screen beyond repair.
To adjust the lower drop, first push the “DOWN” button on your remote to have the screen fully extended.
To increase drop turn the DOWN dial counter in the “+” direction (clockwise).
To reduce drop turn the DOWN dial in the “-” direction (counter clockwise).
INSTALLATION
10