Remaco TEN MXL Series User manual

MPC-851 Motor/Power Controller
with Radio Frequency Receiver
PCB Front Casing
Accessories Included:
Warning
Upper Limit
Screen Frame
+-
More Less -
UP
Installation Guide / Manual - TEN MXL Screen
CCOPYRIGHTS 1998 REMACO TECHNOLOGIES PTE LTD Website: www.remacotech.com
V: 12.0
TEN(MXL)
All products are thoroughly inspected and fully tested operational in factory.
We accept no liability whatsoever for any losses due to improper operation, or any unauthorized alternation.
All trademarks contained in this installation guide are the property of their respective owners.
AVA-316-RF 15-Ch
Radio-Frequency Remote
AVA-200+
Touch-Contact Switch
Front Back Surface Box
Threaded
rod
Ceiling Suspension
with Threaded rod
Truss Mount
Chain down
Ceiling Suspension
with chain
Chain
384mm
350mm
340mm
Shackle
Truss
Setting
button
Front Back

D14
CH2(DRY)
ANT1
IR
B (Rx)
A (Gnd)
RS-485
(RS-232)
GND IR (VDD) 2D 2U COM 1D 1S 1U COM
CH2 CH1
-12V
+12V
-12V
+12V
CH1
CH2
MOTOR 2
POW-IN
+12V
GND GND
N
L
2S
UP1
DN1
N
N
L
N
VCC
>
_
>
>
>
AVA-200
AVA-200+
Wall Switch
(Included)
C o n t a c t C l o s u r e
D r y C o n t a c t
AVA-210A
IR Sensor
(Optional)
IR Sensor
Power Supply Motor 2 Motor 1
AC Input
Projector Lift Computer
A/V Control System
(e.g. AMX / Creston)
AVA-316
15-Channel
RF Remote
(Included)
Learning
Button
Controlled
Equipments
Live(Red)
Neutral(Blue)
Connect to a 230V power supply.
Power
ApplicationConnection
LN
AC Power
Input
For connection to up to 2 electrical motor powered equipments capable of
bi-directional movements.
N D
Projector Lift
Projector Screen
Neutral(Blue)
Down(Black)
Up(Brown)
N2 UP2 N DN1 UP1
Neutral(Blue)
Down(Black)
Up(Brown)
Wiring Diagram
Wire Guage AWG 22
Wire Guage AWG 22
MOTOR 1
DN2UP2
Screen Width
* For details dimension of the screen, please refer to technical specifications at
www.remacotech.com

+-
+-
DOWN
UP
Contact Closure
(Momentary)
RS-485 (RS-232)
Control
Connection Application
IR Sensor
AVA-200+
Down(Pink)
Up(Purple)
Common(Orange)
Up
+
+
....
Down
Stop
Com
Stop(Grey)
1D
1S
1U
COM
For control by an A/V control system (e.g. AMX or Creston) or a Touch-Contact
Switch (Remaco AVA-200+)
* For this zero voltage Contact Closure, any DC voltage exceeding 3V might
damage the MPC
* Works on momentary contact closure only. (Dry contact, normally open)
For connection to an IR Sensor
- To be used in conjunction with a remote controller for controlling of equipments
* Maximum cable length between IR Sensor and MPC is up to 1.45m.
GND
IROUT
VCC
(Yellow)
IR Sensor ( )
(Red) Item only
available in
Bundle Pack
Max 1.45m
(Blue)
MPC-851 can be remotely controlled by using commands send through serial or
USB port. MPC can be configured to “Independent Mode” or “Combine Mode”
by the given software “MPC-851 Program.exe”
*For more details, download from Remaco Website www.remacotech.com
B (Rx)
A (Gnd)
RS-485
(RS-232)
To set screen to your desired “up” and “down” positions.
Bottom View
Adjust “ - ” : screen roll away from frame (anti-clockwise)
screen roll into the frame (clockwise)Adjust “ + ” :
STOP
Allen Key (# 4mm) to set
limit switch knob
Upper Limit
Lower Limit
Adjust “ - ” : less screen drop (anti-clockwise)
Adjust “ + ” : more screen drop (clockwise)
Screen Frame
Lower Limit
Red Knob
Upper Limit
White Knob

up and down
End
Details action and observation:
Connect motors and
power to MPC according
to diagram.
Switch on
power supply
Press and hold the
learning button,
do not release.
Motor will
step-move up
and down
LED starts
flashing
Release
holding the
learning button
Set AVA--316 RF
remote to CH
“1”
Press the
“UP” button
Motor will
step-move
LED stops
flashing
AVA-316 RF remote CH “1”
is now paired with motor 1
1. Connect motors and power to MPC according to diagram.
2. Switch on power supply.
3. Press and hold the learning button, do not release. Motor will step-move up and down
4. Wait for LED to start flashing, and then release holding the learning button .(Wiring Diagram - Page 2)
5. To pair motor 1, set the channel at the AVA-316 RF remote to “1”.
6. Press the “UP” button. Motor 1 will step-move up and down. LED stops flashing. AVA-316 RF remote CH1 is now paired with
motor 1.
7. To pair motor 2, repeat above step 1 to 6
** If nothing is pressed within 20 seconds, motor will revert back to working mode automatically with a step move up and down.
Pairing MPC-851 with AVA-316-RF 15 Ch
Important Note
The upper limit and lower limit of the screen had been preset in factory. Any adjustment to these 2 limit
switches may cause damages to the screen fabric. If adjusted, it will cause the following problems:
a) The screen will roll into the frame and stop by force and not by the Upper Limit switch.
This will cause overheating of motor which unable the screen to operate properly.
b) The depression of the bottom bar onto the fabric will cause horizontal mark on screen surface.
c) Adjusting the Lower Limit of the screen any lower than beyond the STOP sticker may cause the fabric
to drop off
Disclaimer
Any adjustment to these 2 limit switches will void the warranty for the screen and Remaco will hold
no responsibility for any damages to it. Please consult us if it is necessary to do any adjustment to the
limit switch.
To set screen to your desired “up” and “down” positions.
MPC-851 compatible with AVA-316 15-Channel Radio Frequency Remote
Stop button
Down button
Channel - Channel +
LCD screen
Up button
AVA-316-RF 15Ch
OPTION
Setting Number of Channels Used AVA-316 15-Channel RF Remote
OK
Setting
is OK
5C15 8
Press
Channel ‘<’ & ‘>’
together
The screen
will display C
The screen
will display 15
Press
Channel ‘<’ & ‘>’
together
Select the number of channel required
Example ‘2’ by pressing
‘<’ or ‘>’ Stop X1
The screen
will display 0
Or
15