Seville Classics AIRLIFT OFF65859 User manual

Customer Service Informaon
Telephone: [phone]
Fax: [phone]
Hours: 8:30 AM – 4:30 PM (PST)
Email: Suppor[email protected]
Homepage: www.SevilleClassics.com
092019
AIRLIFT® 360 Gas-Spring
Single Adjustable Desk Mount
Monitor Arm
Model: OFF65859
Thank you for choosing Seville Classics! We hope that you enjoy your
monitor arm! Please read through this user guide for parts list, assembly
instrucons, frequently asked quesons and further contact informaon.
4-2018

MONITOR MUST BE VESA MIS-D SPEC C COMPATIBLE WITH
75 mm x 75 mm, or 100 mm x 100 mm MOUNTING HOLES
Desk top must be able to support a maximum weight 17.6 lbs (8 kg). Proper
installaon procedure as outlined in the installaon instrucons must be adhered
to. Failure to do so could result in serious personal injury, or even death.
Safety measures must be pracced at all mes during the installaon of this
product. Use proper safety gear and tools for the installaon procedure to
prevent personal injury.
The installaon instrucons must be read and completely understood prior to
installaon of the product. The installaon instrucons must be read to prevent
personal injury and property damage. Keep these installaon instrucons in an
easily accessible locaon for future reference.
A secure structure must support the weight or load of the display,
when mounng to a wall that contains wooden studs, dead center of the
wooden stud must be conrmed prior to installaon.
Do not install on a structure that is prone to vibraon, movement or
chance of impact. Failure to do so could result in damage to the display
and/or damage to the mounng surface.
Do not install near heater, replace, direct sunlight, air condioning or
any other source of direct heat energy. Failure to do so may result in
damage to the display and could increase the risk of re.
Installaon should be performed by at least 2 people. Injury and/or
damage can result from dropping or mishandling the display.
Recommended mounng surfaces: wooden studs and solid-at
concrete. If the mount is to be installed on any surface other than
wooden studs, use suitable hardware (which is commercially available).
FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY,
SAFETY AND OPERATING INSTRUCTIONS AND WARNINGS
REGARDING THE USE OF THIS PRODUCT MAY RESULT IN
SERIOUS BODILY INJURY
Safety Instructions
STEP 5.
Aach WIRE CLIP (M) along the neck and monitor arm.
Route monitor cables through clip.
FAQS
Q. How big of a screen can each arm t?
A. Each arm can t a screen 15" to 27" across.
Q. How much desk space do I need to install?
A. Clear a 4.5" x 6" space on your desk top for the base clamp.
Q. Can I adjust each arm individually?
A. Absolutely! Adjust the tension and move each monitor independently.
Specicaons
Dimensions: 22.44" W x 5.8" L x 12" H
Base dimensions: 4.5" W x 5.8" L x 2.75" H
Weight capacity: 17 lbs. (8 kg)
Weight: 6.4 lbs.

STEP 5. Adjust the tension in MOUNT (A) with HEX KEYS (I, K).
Turn CLOCKWISE to reduce tension.
Turn COUNTER-CLOCKWISE to increase tension.
3 mm Hex Key 5 mm Hex Key
TIP! Use more tension for heavier monitors and to stabilize your
screens if they move too easily or droop aer adjusng.

Parts List
A. Mount (1)
Please make sure you have all the parts on this list.
If you’re missing parts, contact us for replacements at
[phone] or send an email to [e-mail]
Screwdriver
Required Tools (not included)
B. Arm (1)
C. Neck (1)
D. M4x30 Screw (4)
E. M4x12 Screw (4)
G. Kingpin (4)
H. Cap (4)
I. 3 mm Hex Key (1)
K. 5 mm Hex Key (1)
F. Spacers (4)
M. Wire Clip (1)
J. 4mm Hex Key (1)
L. Grommet Plate (1)
STEP 4. Slide monitor onto end of ARM (B). Screw KINGPIN (G)
through boom end of ARM (B) into MOUNT (A). Insert CAP (H).

For Monitors with Flat Backs
STEP 3a. Align MOUNT (A) with screw holes in rear of monitor.
Aach with M4x12 SCREWS (E). Tighten unl snug.
For Monitors with Curved/Recessed Backs
STEP 3b. Posion SPACERS (F) between rear of monitor and end of
MOUNT (A). Aach with M4x30 SCREWS (D). Tighten unl snug.
Assembly Instrucons (clamp mount)
STEP 1A. Unscrew clamp on base of NECK (C) and t onto desk.
Tighten clamp unl snug.
Assembly Instrucons (clamp mount)
STEP 1B. Unscrew clamp using 5 mm HEX KEY (K).
Unscrew clamp plate with Phillips screwdriver.
IMPORTANT : DO NOT DISCARD Clamp Plate or Handle.
Handle
Clamp plate

Pull o pad from base to access screws.
Remove screws from base with 4 mm HEX KEY (J), and remove bracket.
Aach GROMMET PLATE (L) to base using 4 mm HEX KEY (J).
Reaach pad to base.
Place NECK (C) on top of grommet hole. Screw handle through plate
and into monitor arm unl snug.
Assembly Instrucons (Arm Installaon)
STEP 2. Adjust neck right to desired height.
Turn latch clockwise to ghten unl snug.
Slide ARM (B) over NECK (C).
Latch
Plate
Handle