Sevylor QuikPak User manual

READ THE FOLLOWING
INSTRUCTIONS AND WARNINGS TO AVOID
DROWNING OR SERIOUS INJURY
INFLATABLE
QUIKPAK™ KAYAKS
INFLATABLE QUIKPAK™ KAYAKS
®
®
WARNING!
Failure to follow these warnings could cause SEVERE INJURY or DEATH.
● CONSULT WITH A PHYSICIAN p rior to beginning paddle sport training.
Paddle sports can be very dangerous and physically demanding.
●
OBTAIN PADDLESPORT TRAINING specific to this type of craft. Do not
exceed your padding ability - be honest with yourself. Obtain certified first aid
training and carry first aid and safety/rescue equipment.
●
WEAR U.S COAST GUARD APPROVED LIFE JACKETS,
and where appropriate, wear a helmet.
●
NOT A LIFE SAVING DEVICE.
● NEVER PADDLE ALONE.
● CHECK WEATHER FORECAST BEFORE DEPARTING DOCK and heed all
weather advisories.
● DRESS APPROPRIATELY for the weather conditions, as cold water
and/or cold weather can cause hypothermia.
● DO NOT PADDLE IN FLOOD CONDITIONS.
● BE AWARE OF THE WATER CONDITIONS, including appropriate water
levels,tidal changes, dangerous currents and other water hazards. Do not use in
high wind, strong currents, open water or dangerous tides. Always scout
unfamiliar waters, and portage where appropriate.
● NEVER PADDLE WHILE UNDER THE INFLUENCE
of drugs or alcohol.
● KEEP PROPER LOOKOUT AND SAFE
DISTANCE from other vessels and hazards
at all times.
● OBEY APPLICABLE BOATING LAWS. Know and follow local water safety
rules and boating regulations.
● READ THE OWNER’S MANUAL and follow the manufacturer’s
recommendations for the use this product. It is the owner’s responsibility to
carefully read the manual and instruct all users in safe operation of this product.
Consult the manufacturer’s information prior to adding aftermarket equipment.
● DO NOT OVERLOAD OR OVERINFLATE. Adults should inflate the
chambers in numbered sequence.

INFLATABLE QUIKPAK™ KAYAKS
2
IMPORTANT INFORMATION
The warnings below relate to various situations. Please observe them.
These products are made of the highest quality materials and comply
with NMMA (National Marine Manufacturers Association) regulations.
Denotes an imminent hazard which will result in severe injury if
you do not comply with the instructions.
CAUTION!
These products are not meant for towing because the extreme
pressure of the water while towing can tear the eyelets
and/or handles.
WARNING!
Altering the construction of these products could jeopardize the
safety of the occupants and will void the limited warranty.
CAUTION!
It is the owner’s responsibility to make sure all users
carefully read and follow the instructions for safe operation
of this product. Observe all local and national laws. Always
wear a Personal Flotation Device approved by the proper
authorities. Please carefully observe the Capacity Plate
information which is printed on the product.
CAUTION!
Reminds you of safety measures which must be observed. Also
denotes unsafe practices which could result in personal injury
or damage to the product or property, if you do not comply with
the instructions.
WARNING!

INFLATABLE QUIKPAK™ KAYAKS
3
INFLATION INSTRUCTIONS
To inflate using any Sevylor®Pump:
Do not over inflate. Pressurize product to “Inflation
Pressure” stated in the chart for your specific product.
CAUTION!
Never use a compressor, CO2or compressed air to inate the
product. Do not let your product come into contact with sharp,
pointed objects.
WARNING!
Please complete the “if found label” located on the boat with the boat
owners contact information in large print with a permanent marker.
IF FOUND - CONTACT
SI SE ENCUENTRA - COMUNICARSE CON
EN CAS DE DÉCOUVERTE – CONTACTEZ
Name/Nombre/Nom:
Phone/Teléfono/Téléphone:
Phone/Teléfono/Téléphone:
3. When fully inflated, seal valve by pushing
in with adapter nozzle. This will seal the
internal yellow stopper and keep air from
escaping while closing cap. Gently twist
adapter while backing hose out of valve.
4. Fully remove pump and hose and close
external cap. Valve should appear
depressed into itself.
1. To begin inflation, open external cap and pull
firmly on the lanyard to extend out. This will
open internal yellow seal.
2. Attach nozzle of hose to inflation end of
pump. Insert adapter nozzle into valve
and start pumping.

INFLATABLE QUIKPAK™ KAYAKS
4
IMPORTANT! Inate the product chambers in the following order:
K5 QuikPak™ Kayak
1. Inate the oor chamber.
2. Inate the DIN chamber.
3. Inate the outside main chamber.
K1 QuikPak™ Kayak
1. Inate the two foot wells chambers.
2. Inate the inner main chamber.
3. Inate the outer main chamber.
4. Inate seat back.
The chambers on the product will also be numbered to indicate order
of ination. This order of ination will ensure the proper volume and
buoyancy of the safety chamber.
Note: To inate the mini Double Lock™ valve, which is used on
some of the Sevylor product oors and seat bottoms, follow the
same ination instructions above, using the mini Double Lock™
valve adapter. The mini Double Lock™ valve adapter is included with
all Sevylor®pumps. The adapter can be purchased from Customer
Service by calling 1-800-835-3278 US | 1-800-387-6161 CA (Part
Number 5010000707).
Water temperature and weather do affect the pressure in inatable
products. In cold weather your product will lose some pressure due
to the fact the air will contract. If this occurs, you may want to add
a little air to improve your product’s performance. However, in hot
weather, the air will expand. You must let some air out to prevent
your product from failing due to overpressure. You should avoid
exposing your product to extreme temperatures (hot or cold).
CAUTION!
DEFLATION INSTRUCTIONS
Deflation instructions using any Sevylor®Pump:
Remove nozzle of hose from inflation end and attach to
opposite deflation end of pump. Repeat same steps as
inflation. This will draw the air out quickly.

INFLATABLE QUIKPAK™ KAYAKS
5
K5 QuikPak™ Kayak Set Up Instructions
1. Remove QuikPak™ kayak from box.
3. Unbuckle inner support straps.
5. Pull shoulder straps through openings
in QuikPak™ unit.
7. Fold over side flaps and secure with the
hook & loop strips.
4. Remove kayak from QuikPak™ unit and
set kayak aside.
6. Fold bottom flap and inner support straps
into the QuikPak™ unit.
8. Turn seat over and set aside.
2. Unbuckle waist strap and shoulder straps.
Unzip or remove spray skirt.
Spray Skirt
Waist Straps
Shoulder Straps
Inner Support
Straps
Shoulder
Straps

INFLATABLE QUIKPAK™ KAYAKS
6
Inflate Kayak (using order shown below)
9. Inflate outer chamber to 0.9 PSI.
11. Inflate floor chamber to 0.9 PSI.
14. Place seat in kayak with the hook & loop
strips secured as shown in step 13.
13. Line up hook & loop strip on seat bottom with the hook & loop strip on the kayak floor.
10. Inflate DIN chamber to 0.9 PSI.
12. Take seat that was set aside in step 8, fold
with hook-and-loop strips downwards as
shown.
15. Attach back rest buckles on seat to the
buckles on the kayak.
Outer Chamber
Valve
Seat Back
Seat Hook &
Loop Strip
Kayak HookKayak Hook
& Loop Strip& Loop Strip
Back RestBack Rest
BucklesBuckles
Seat Bottom
Floor ChamberFloor Chamber
ValveValve
DIN Chamber
Valve

INFLATABLE QUIKPAK™ KAYAKS
7
K5 QuikPak™ Kayak
Breakdown/Storage Instructions
16. Adjust backrest straps to desired tension.
1. Remove kayak seat.
2. Remove spray skirt and deflate kayak.
3. Unfold side flaps, bottom flap & inner
support straps.
5. Fold kayak using the following steps.
5a. Fold kayak lengthwise to center as shown
in the above image.
17. Zip spray skirt onto kayak.
4. Pull shoulder straps through the openings.
Back RestBack Rest
StrapsStraps
Spray SkirtSpray Skirt
Spray SkirtSpray Skirt
5b. Fold kayak lengthwise again as shown in
the above image.
5c. Fold over ends of kayak as shown in the
above image.
Your QuikPak™ Kayak is now ready for use.

INFLATABLE QUIKPAK™ KAYAKS
8
5d. Fold over ends of kayak again as shown in
the above image.
5e. Fold kayak in half, with strake up, as shown
in above image.
6. Place folded kayak into QuikPak™ unit.
8. Attach spray skirt to QuikPak™ unit.
Your QuikPak™ kayak is now ready to transport or store.
7. Buckle & tighten horizontal support strap.
Buckle & tighten vertical support strap.
9. Store pump in cargo net on rear of
QuikPak™ unit. Store paddle in side
pockets and use hook & loop straps to
secure the top of the paddle shafts.
VerticalVertical
Support StrapSupport Strap
PaddlePaddle
Hook & LoopHook & Loop
StrapsStraps
PaddlePaddle
PocketsPockets
HorizontalHorizontal
Support StrapSupport Strap

INFLATABLE QUIKPAK™ KAYAKS
9
1. Remove QuikPak™ Kayak from box.
3. Turn QuikPak™ unit over and unbuckle the
support strap.
4. Pull the male buckles on cargo net out from
each female buckle.
6. Remove kayak and set aside. Fold shoulder
straps into QuikPak™ unit as
shown above.
2. Unbuckle shoulder straps & waist strap.
5. Remove cargo net and set aside.
K1 QuikPak™ Kayak Set Up Instructions
Shoulder
Straps
Waist
Strap
Support
Strap
SupportSupport
StrapStrap
FemaleFemale
BuckleBuckle
MaleMale
BuckleBuckle
Cargo Net
8. Fold over right side flap of QuikPak™ unit,
attaching the hook & loop strips to secure
the QuikPak™ unit side flaps.
7. Fold over left side flap of QuikPak™ unit,
as shown above.
NOTE: Left side must be folded over first
so the hook & loop strips can
be attached.
Hook & Loop StripsHook & Loop Strips

INFLATABLE QUIKPAK™ KAYAKS
10
10. Inflate kayak using the following steps.
10a.Inflate foot wells to 0.5 PSI.
10c. Inflate outer chamber to 0.5 PSI.
12. Insert each male buckle into the slots
on kayak.
11. With male buckles facing downward, place
cargo net onto kayak in the position as
shown above.
9. Buckle & tighten the support strap and
set aside.
10b.Inflate inner chamber to 0.5 PSI.
10d.Inflate seat back to 0.5 PSI.
Support StrapSupport Strap
Foot WellFoot Well
ValvesValves
Outer ChamberOuter Chamber
ValveValve
Seat Back ValveSeat Back Valve
InnerInner
ChamberChamber
ValveValve
Inflate Kayak (using order shown below)

INFLATABLE QUIKPAK™ KAYAKS
11
15. Align hook & loop strip on kayak with the hook & loop strip on the bottom of the seat.
16. Connect the seat back strap buckles to the
buckles on the kayak.
1. Remove kayak seat, remove cargo net &
deflate kayak.
2. Unfold kayak seat in reverse order
(QuikPak™ unit should look as
shown above).
17. Adjust seat back straps to your
desired tension.
3. Fold kayak using the following steps.
3a. Fold kayak lengthwise to center as
shown above.
Kayak HookKayak Hook
& Loop Strip& Loop Strip
Seat BackSeat Back
Strap BucklesStrap Buckles
Strap BucklesStrap Buckles
Kayak HookKayak Hook
& Loop Strip& Loop Strip
Pull Strap toPull Strap to
TightenTighten
K1 QuikPak™ Kayak
Breakdown/Storage Instructions
13. The cargo net installed onto kayak. 14. Kayak seat.
Seat BackSeat Back
Seat BottomSeat Bottom

INFLATABLE QUIKPAK™ KAYAKS
12
3d. Fold over other end of kayak, as
shown above.
4. Place kayak into QuikPak™ unit.
6. Install cargo net, as shown above (Refer
to step 4 of K1 setup instructions for
assistance).
8. Store pump in cargo net on rear of
QuikPak™ unit. Store paddle in side
pockets and use hook & loop straps to
secure the top of the paddle shafts.
Your QuikPak™ kayak is now ready to transport or store.
3e. Fold kayak in half, as shown above.
5. Fold up left & right side flaps, buckle &
tighten support strap.
7. Buckle shoulder straps.
ShoulderShoulder
StrapsStraps
PaddlePaddle
PocketsPockets
Hook & LoopHook & Loop
Straps forStraps for
SecuringSecuring
Paddle ShaftsPaddle Shafts
3b. Fold kayak lengthwise again, as
shown above.
3c. Fold over end of kayak, as shown above.

INFLATABLE QUIKPAK™ KAYAKS
13
OPERATING INSTRUCTIONS:
• Follow all local boating regulations and navigation rules.
Familiarize yourself with boating conditions where you plan to
use the boat. Use common sense and caution when operating in
unfamiliar places.
• Observe the maximum weight the product can carry and do not
overload past this limit. Over-loading jeopardizes the safety of
the occupants.
• Be sure all accessories and/or equipment (e.g. oars, life jackets)
are in proper working condition before using the boat. Each
person occupying the boat is to wear an approved Personal
Flotation Device (life preserver).
• Sharp objects are not to be carried in the product without
adequate protection or storage.
• When navigating the product in any water depth, watch for
submerged or sharp objects that may damage or pierce the
boat’s air chambers.
• Enter the product from the port (left) or starboard (right) sides -
not from the fore (front) or aft (back) sides.
• Never tow with a boat or any other vehicle.
NMMA (ABYC
Standard)
Persons
Capacity
Maximum
Payload Capacity
Inflation
Pressure
Inflation
Pressure
Model # Persons Only Persons, Gear Main Chamber(s) Floor Chamber(s)
K5 QuikPak™ Kayak 1 Pers. or 250
lbs. 250 lbs. 0.9 PSI 0.9 PSI
K1 QuikPak™ Kayak 1 Pers. or 400
lbs. 400 lbs. 0.5 PSI 0.5 PSI
Your product is NMMA certied using the ABYC standard .
Do not exceed the certified maximum capacities under any circumstances!
WARNING!

INFLATABLE QUIKPAK™ KAYAKS
14
REPAIRING SMALL PUNCTURES
For inadvertent punctures, you can repair them with the included
Sevylor®repair patch.
INSTRUCTIONS:
1. Thoroughly clean and dry the damaged area. Completely deate
if an inatable article.
2. Cut a portion of the patch to cover the puncture, and allow an
additional ¼" on all sides. Always cut a round or oval patch.
Never leave corners.
3. Be sure the spot is completely dry.
4. Peel the backing from the patch.
5. Adhere the patch to the puncture.
6. Using your thumb or nger apply even pressure across the entire
surface of the patch.
CARE & STORAGE:
• You product is made of the highest quality materials and comply
with NMMA (National Marine Manufacturers Association)
regulations. Altering the construction of these products will void
the limited warranty and could jeopardize the safety of
the occupants.
• If your product has been used in salt water, rinse it off with fresh
water as soon as possible.
• Remove tar spots or other soiled areas by using a mild soap and
rinsing with fresh water.
• Be sure your product is completely dry before storing.
• The products may be stored inated, but do not place any heavy
or sharp objects on it. Storage is best in a dry room.
MOTOR MOUNTING
Do not mount a motor on any of these kayaks.
CAUTION!

INFLATABLE QUIKPAK™ KAYAKS
15
PADDLE ASSEMBLY:
SELECT MODELS ONLY.
Join the three shafts together by screwing them together with the
two couplers. Attach the blade to the shafts by screwing onto the
end of the shaft.
GUIDELINES FOR USAGE:
These kayaks may be wider than a typical kayak, which means they
may feel more stable. However, as with any narrow, at bottom
kayak, users must be aware of the possibility of the kayak tipping
and compensate for it. Paddle with short, even and easy strokes.
Paddle close to the kayak with the paddle almost vertical. Pull with
one hand and push with the other. If the nose of the kayak is moving
right to left you are probably paddling too hard. Ease off on the
force of your stroke to reduce the swaying of the front end. Paddling
backward or breaking can sometimes offer quick maneuverability.
Blade Shaft Shaft Shaft
Coupler Coupler
Blade

4010025816 (ECN0069301-C)
Limited One Year Warranty
The Coleman Company, Inc. (“Coleman”) warrants that for a period of one (1) year from the date
of original retail purchase, this product will be free from defects in material and workmanship.
Coleman, at its option, will repair or replace, free of charge, this product or any component of the
product found to be defective during the warranty period. Replacement will be made with a new
or remanufactured product or component at no cost to the consumer. If the product is no longer
available, replacement may be made with a similar product of equal or greater value. No warranty
is provided for batteries and light bulbs. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is
not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty
performance. Coleman dealers, service centers, or retail stores selling Coleman® products do not
have the right to alter, modify or in any way change the terms and conditions of this warranty.
What This Warranty Does Not Cover
This warranty does not cover normal wear of parts, parts that are not genuine Coleman® parts,
or damage resulting from any of the following: negligent use or misuse of the product; use
on improper voltage or current; commercial use of the product; use contrary to the operating
instructions; disassembly, repair or alteration by anyone other than Coleman or an authorized
service center. Coleman expressly excludes from this warranty and denies liability for defects or
damage caused by repair or alteration by anyone other than Coleman. Further, the warranty does
not cover Acts of God, such as fire, flood, hurricanes and tornadoes. Warranty void if damage to
the product results from the use of a part other than a genuine Coleman® part.
No terms of this warranty may be construed to apply to non-warranty service and maintenance.
Accordingly, Coleman also denies liability for defects and damage caused by the use of
unauthorized parts, repair, service or alteration outside the terms of this warranty.
COLEMAN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES CAUSED BY THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR
CONDITIONS. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS
LIMITED IN DURATION TO THE DURATION OF THE ABOVE WARRANTY OR CONDITIONS.
SOME STATES, PROVINCES, OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE OR PROVINCE TO
PROVINCE.
How to Obtain Warranty Service
Your product must be under warranty in order to obtain warranty service. If your product is
defective and is within your warranty period, contact us at 1-800-835-3278 (TDD 1-316-832-8707)
in order to receive a return authorization. Do not return product to Coleman without authorization.
You will be directed to attach a tag to the product that includes your name, address, daytime
telephone number and description of the problem. Include a copy of the original sales receipt.
Carefully package the product and send insured by UPS, FedEx Ground or Parcel Post with
shipping and insurance prepaid to:
For products purchased in the United States:
The Coleman Company, Inc.
3600 North Hydraulic
Wichita, KS 67219 U.S.A.
The cost of transporting the product to Coleman for warranty service is the responsibility of the
purchaser.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE. DO NOT SHIP WITH THE
BATTERIES INSTALLED.
If you have any questions regarding this warranty please call 1-800-835-3278 or TDD 1-316-832-8707
in the United States or 1-800-387-6161 in Canada.
3600 North Hydraulic • Wichita, KS 67219 U.S.A.
1-800-835-3278 US |1-800-387-6161 CA
© 2023 The Coleman Company, Inc. All rights reserved.
Double Lock™ and QuikPak™ are trademarks of The Coleman Company, Inc.
Sevylor®and are registered trademarks of The Coleman Company, Inc.
For products purchased in Canada:
Newell Brands Canada ULC
20B Hereford Street
Brampton, ON L6Y 0M1
INFLATABLE QUIKPAK™ KAYAKS
16