Shark EP724 User manual

IMPORTANT SAFETY INSTRUCTIONS
When using your Bagless Cyclonic Canister vacuum, basic safety precautions
should always be observed, including the following:
WARNING: To reduce the risk of fire,
electrical shock, or injury:
1. Do not leave vacuum cleaner unattended
when it is plugged in. Unplug from
outlet when not in use.
2. To reduce the risk of electric shock – do
not use outdoors or on wet surfaces. Do
not handle plug or vacuum cleaner with
wet hands.
3. Do not allow children to use as a toy.
Close attention is necessary when used
by or near children.
4. Use only as described in this manual. Use
only manufacturer’s recommended
attachments.
5. Do not use with damaged cord or plug. Do
not use vacuum cleaner if it has been
dropped, damaged, left outdoors, or
dropped into water. Return appliance to
EURO-PRO for examination, repair or
adjustment.
6. Do not pull or carry by cord. Do not use
cord as a handle, close a door on cord,
or pull cord around sharp edges or
corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
8. Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
9. Do not pick up hot coals, cigarette butts,
matches or any hot, smoking, or burning
objects.
10. Do not pick up hard or sharp objects such
as glass, nails, screws, coins, etc.
11. Do not use without filters in place.
12. Turn off all controls before plugging or
unplugging vacuum cleaner.
13. Use extra care when vacuuming on
stairs.
14. Do not pick up flammable or
combustible materials (lighter fluid,
gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
15. Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
16. Do not use in an enclosed space filled
with vapors given off by oil based
paints, paint thinner, moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
17. Always unplug this appliance before
connecting or disconnecting vacuum
hose. Always hold the plug when
rewinding the power cord. Do not allow
plug to whip when rewinding.
18. Use only on dry, indoor surfaces.
19. Do not use for any purpose other than
described in this user’s guide.
20. Use only extension cords UL or cUL-
rated at 15 amperes. Extension cords
rated for less amperage may overheat.
Care should be taken to arrange the
cord so that the cord cannot be pulled
or tripped over.
21. Do not put any objects into openings.
Do not use with any opening blocked.
Keep free of dust, lint, hair and
anything else that may reduce air flow.
22. Store your appliance indoors in a cool,
dry area.
23. Keep your work area well lit.
24. Do not immerse the hand vacuum into
water or other liquids.
25. Keep end of hose, wands and other
openings away from your face and
body.
Bagless Cyclonic Canister
OWNER’S MANUAL
Model EP724
120V~, 60Hz., 12 Amps
SAVE THESE INSTRUCTIONS
For Household Use Only
For information or assistance:
EURO-PRO Corporation
178 W. Service Rd.
Champlain, NY 12919
Tél. : 866-98shark
www.sharkvac.com
WARNING: To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not modify the plug in any way.
Rev. 12/02E
1

GETTING TO KNOW YOUR BAGLESS CYCLONIC
CANISTER PRECAUTIONARY MEASURES
Important:If the suction opening of the unit, the hose or the chrome telescopic tube
are BLOCKED, switch off the vacuum cleaner and remove the blocking
substance before you start the unit again.
1. On/Off Button
2. Cord Rewind Button
3. Carrying Handle
4. Dust Cup
5. Dust Cup Cover
6. Dust Cup Cover Release
7. Hose Connector Inlet
8. Hose Connector
9. Floor to Carpet Brush
10. Chrome Telescopic Tube
11. Curved Wand/Hose Extension
12. Flexible Hose
13. Air Driven Turbo Brush
14. Crevice Tool
15. Upholstery Brush
16. Trap Door Release Button
4. When pulling out the power plug
from the wall outlet, pull the plug
not the power cord.
1. Do not operate the vacuum
cleaner too close to heaters or
radiators.
5. Do not pick up anything that is
burning or smoking such as
cigarettes, matches or hot ashes.
2. Before inserting the power plug
into the wall outlet, make sure that
your hands are dry.
6. Do not use without all filters in place.
Note: This vacuum cleaner is equipped
with a plug and power cord that retract
automatically. If the cord or plug get
damaged, it must be replaced by a
qualified technician.
3. Before you start vacuuming,
make sure to remove large or
sharp objects that might
damage the dust bag.
Warning: Hold the plug when
rewinding the cord. Do not allow the
cord to whip when rewinding.
Technical Specifications
Main Unit: Voltage: 120V~, 60Hz.
Power: 12 Amps
23

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
Crevice Tool and Dusting Brush
Assembling Your Vacuum Cleaner 4. Fitting the Floor to Carpet
Brush or the Air Driven Turbo
Brush to the Telescopic Tube
Push the telescopic tube into the
desired floor brush as show in the
illustration below.
3. To rewind the power cord, press the
cord rewind button with one hand
and hold the plug of the power cord
with the other hand to ensure that it
does not whip causing damage or
injury.
Note: Always remove the power plug
from the wall outlet before assembling or
removing accessories.
1. Crevice Tool with Brush
For radiators, crevices,
corners, baseboards and
between cushions.
2. Upholstery Brush
The dusting brush is used
for the furniture
2. Fitting the Chrome
Telescopic Tube to the
Curved Wand / Hose
Extension
Push the chrome telescopic tube
into the curved wand / hose
extension, as shown in the
illustration below.
Plastic
Button
3. Extending the Chrome
Telescopic Tube
Push forward on the plastic button
and pull the inner chrome tube
outward.
Floor to Carpet
Nozzle
Air Driven Turbo
Brush
5. Air Driven Turbo Brush
The efficiency of your Air Driven
Turbo Brush depends on the bristle
brush rotating at high speed. Strong
air suction is needed to accomplish
this. In order to ensure that
maximum air suction is maintained,
please read the following instructions:
• Empty the Dust Cup frequently during
use.
• Always “TapClean” the HEPA dust
cup filter each time the dust cup is
emptied.
• Ensure that the rotating bristle brush
is kept free of hair and string.
• Inspect the turbine regularly to ensure
that the air passage is free of dirt and
debris. See cleaning instructions on
page 8.
1. Attaching the Flexible Hose
into the Vacuum
Connect the flexible hose into the
hose connector inlet. Push in until
you hear a “click”, indicating it is in its
locked position.
Motor Thermostat
Telescopic
Tube Important: This vacuum cleaner is
equipped with a motor protective
thermostat. If for some reason your
vacuum overheats, the thermostat will
automatically turn the unit off. Should this
occur, unplug the vacuum from the wall
outlet and turn off the switch. Empty the
dust cup, "TapClean" the dust cup filter
and check for blockages in hose and
suction inlet. Allow the unit to cool for a
minimum of 45 minimum prior to
restarting the unit. To restart, re-plug the
vacuum into the wall socket and turn the
switch back on
Note: Once all attachments are in
place, unwind a sufficient length
of cable and insert the plug into
the wall outlet. A yellow mark on
the power cord shows the ideal
cable length. Don't pull the power
cord beyond the red mark.
1. Insert the power plug into the wall
outlet.
2. Press the Power On/Off button
located on the unit to turn the
vacuum cleaner "On".
Using your Vacuum
5
4

7
Important:The suction hole must be
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
is properly
"TapCleaned”
after each use
and suction
does not return
to 100%, then
we suggest that
the HEPA filter
be “TapCleaned”
vigorously until
no more dust
can be removed, then rinsed under
the faucet and allowed to dry for 24
hours before refitting into the vacuum.
(Fig. A) This should be done once a
month or when suction appears to
be reduced.
8. Insert the Rinseable
"TapClean" HEPA dust cup
filter back into the dust cup.
9. Re-install dust cup into the
vacuum. Close cover and re-
attach hose.
Fig. A
Warning: Allow 24
hours for drying before
replacing in unit.
Wash
once a
month or
when
suction
appears
reduced
Changing & Cleaning the
Pre-Filter
The pre-filter is located on the top of the
Rinseable "TapClean" HEPA filter. See
illustration below.
This is a rinseable filter but should be
replaced every three (3) months. Never
operate the vacuum without ALL the
filters in place.
• Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
• Open the dust cup cover and remove
the dust cup being careful not to press
on the trap door release button.
• Remove the HEPA filter and hold the
tab that is on the top of the filter and
pull until the filter cover snaps off.
• Rinse pre-filter in lukewarm water, let
dry completely. Do not use a washing
machine to rinse the filter. Do not use
a hair dryer to dry it. Air dry only.
• Replace only when the pre-filter is
completely dry, replace into HEPA
filter and snap the cover back in
place.
PLEASE NOTE: The white pleated
7. Vigorously “TapClean”
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter. See
illustration at right.
IMPORTANT: Please note that there
is a safety switch inside the vacuum
where the dust cup is inserted to
prevent the unit from being run
without a dust cup filter in place. If the
dust cup filter has not engaged this
safety switch, the vacuum will NOT
operate. Therefore, ensure that the
dust cup filter is inserted firmly into the
vacuum when assembling.
OPERATING INSTRUCTIONS
1. Push the Power On/Off button to
"Off" and disconnect the power
cord from the wall outlet.
2. Remove the flexible hose.
3. Push the dust cup cover release
button located on the front side of
the unit (see illustration) and lift
the cover up.
4. Hold the dust cup by the handle
and lift it up out of the vacuum .
5. Hold dust cup over a waste
basket (garbage can), lift cover
and then depress the trap door
release button to open the dust
cup. Dispose of the dust inside.
(See illustrations below.)
Note: If dust is tightly packed and
difficult to remove, tap the side of
the dust cup lightly against the
side of the waste basket (garbage
can).
Lift cover, then depress button
to open trap door
6. To remove the Rinseable
"TapClean" HEPA dust cup
filter from the dust cup, hold the
filter from the tab at the top of it
and lift. See illustration below.
Warning:After each Use - Always
remove the Rinseable "TapClean" HEPA
Filter from the Dust Cup, then vigorously
“TapClean” HEPA Filter until no more
dust can be removed.
Important: When "TapCleaning" the
HEPA filter, hold the HEPA filter from the
top rim and tap ONLY the bottom rim
against the side of the waste container.
NEVER tap directly on the pleated folds of
the HEPA filter.
6
Removing & Cleaning the
Rinseable "TapClean" HEPA
Dust Cup Filter
OPERATING INSTRUCTIONS
Warning: Always unplug the unit from
electrical outlet before removing the Dust
Cup (container).
Top Rim
Bottom Rim
IMPORTANT, Please Note : The
Rinseable “TapClean” HEPA Dust Cup
Filter will stop most of the tiniest dust
particles and airborne allergens from re-
entering the air you breathe. In fact it
stops 99.97% of all particles as small as
0.3 microns - many times smaller than a
human hair!!! Because of this incredible
filtration performance, the HEPA Dust Cup
Filter will quickly accumulate dirt inside
the white filter folds, many fine dust
particles that are difficult to see but which
will eventually block or reduce your
suction power - if not cleaned properly.
Clean the HEPA Filter as described in this
section, then reconnect unit and proceed
with vacuuming.)

OPERATING INSTRUCTIONS
8
Please Note: The HEPA Dust Cup
Filter is washable. It should, however,
be replaced every six (6) months to
ensure peak performance of your
vacuum.
The Post Motor Filter and Pre-Filter are
washable. They should however be
replaced every three (3) months to
ensure peak performance of your
vacuum.
Important: Make sure that ALL filters
are completely dry before re-installing
back in the hand vacuum.
Important: All filters should be checked
regularly for signs of damage,
preferably after each cleaning task. The
filters must be replaced immediately if
they become damaged. Always
disconnect the vacuum from the
electrical outlet when checking the
filters.
Changing & Cleaning the
Pre-Motor Filter
The pre-motor filter is located behind the
dust cup. See illustration below.
This is a rinseable filter but should be
replaced every three (3) months. Never
operate the vacuum without ALL the
filters in place.
• Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
• Open the dust cup cover.
• Remove the pre-motor filter and rinse
in lukewarm water, let dry completely.
Do not use a washing machine to
rinse the filter. Do not use a hair dryer
to dry it. Air dry only.
• When filter is completely dry, replace
pre-motor filter back into the unit and
close the dust cup cover.
Changing & Cleaning the Post
Motor Filter
The post motor filter is a washable filter
but should be replaced every three (3)
months depending on usage. Never
operate the vacuum without ALL the
filters in place.
• Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
• The post motor filter is located on the
rear of the vacuum. Remove the filter
from the filter grill.
• Rinse in lukewarm water, let dry
completely. Do not use a washing
machine to rinse the filter. Do not use
a hair dryer to dry it. Air dry only.
• When filter is completely dry, replace
post motor filter back into the unit and
replace the filter cover.
1. On the base of the turbo brush there is
an access door for the turbine. To
open for cleaning, push latch toward
door and lift door off.
2. Inspect turbine wheel and air passage
for debris and/or blockage. Remove
debris if present.
3. Inspect the rotating brush for built-up
hair or string. If present, remove by
carefully cutting with scissors. Avoid
damaging or cutting bristles.
4. Once clean, snap the turbine access
door back in place. The turbo brush
will not function without the access
door in place..
Cleaning Air Driven Turbo Brush
PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition
when it was shipped from the factory. If a minor problem occurs, it usually can
be solved quite easily when the cause is found. Therefore, this checklist is
provided for your convenience.
PROBLEM POSSIBLE CAUSE POSSIBLE
Cleaner Won’t
Run
1. Not firmly plugged in.
2. No electricity in wall
outlet.
3. On/Off switch not turned
on.
4. Thermal protector tripped.
5. Blown fuse/tripped
breaker.
1. Plug in firmly, push on/off
switch to on.
2. Check fuse or breaker.
3. Push on/off switch to on
4. Reset thermal protector.
5. Reset circuit breaker or
replace fuse.
Cleaner Won't
Pick Up
1. Full or clogged dust cup.
2. Clogged nozzle or dust
cup port.
3. Clogged hose.
4. Hole in hose.
5. Hose not inserted fully.
6. Motor protection system
activated.
7. Dirty filters.
1. Clean dust cup.
2. Remove obstruction.
3. Remove obstruction.
4. Replace hose.
5. Push hose in securely.
6. Reset thermal protector.
7. Clean / change filters.
Air Flow
Restricted With
Attachment Use
Sound Changes
1. Attachment use restricts
airflow.
2. New carpet trimmings
clogging air passage.
1. Check attachment.
2. Remove obstruction.
9

Model EP724
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO CORPORATION warrants this product to be free from defects in
material and workmanship for a period of one (1) year from the date of the
original purchase. This warranty applies only to normal domestic household
use.
Should your appliance fail to operate properly while in use under normal
household conditions within the one (1) year warranty period, return the
complete appliance and accessories, freight prepaid to Euro-Pro Corporation at
the address given below. If the appliance is found by EURO-PRO to be
defective in material or workmanship, EURO-PRO will repair or replace it free of
charge. Proof of purchase date and $19.95 to cover the cost of return shipping
and handling must be included. *
In US: EURO-PRO Corporation, 178 West Service Rd., Champlain, N.Y. 12919
Non-durable parts including, without limitation, rotating brushes and electrical
parts which normally require replacement are specifically excluded from
warranty.
The liability of EURO-PRO Corporation is limited solely to the cost of the repair
or replacement of the unit at our option. This warranty does not cover normal
wear of parts and does not apply to any unit that has been tampered with or
used for commercial purposes. This limited warranty does not cover damage
caused by misuse, abuse, negligent handling or damage due to faulty
packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service
or alterations to the product or any of its parts, which have been performed by a
repair person not authorized by EURO-PRO.
This warranty is extended to the original purchaser of the unit and excludes all
other legal and/or conventional warranties. The responsibility of EURO-PRO
Corporation if any, is limited to the specific obligations expressly assumed by it
under the terms of the limited warranty. In no event is EURO-PRO Corporation
liable for incidental or consequential damages of any nature whatsoever. Some
states do not permit the exclusion or limitation of incidental or consequential
damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to
include proof of purchase date and to attach tag to item before packing
with your name, complete address and phone number with a note giving
purchase information, model number and what you believe is the problem
with item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package
“ATTENTION CUSTOMER SERVICE”.
We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
FOR REPLACEMENT FILTER INFORMATION
for Model EP724
Bagless Cyclonic Canister
Call: 1-866-98SHARK (1-866-987-4275)
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
or
visit our website: www.sharkvac.com
Replacement filters SKU# XSH724
FOR TECHNICAL SUPPORT
for Model EP724
In U.S.: 800-798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
Please Note:
The HEPA Dust Cup Filter may be washed. We recommend that this be done once a
month or when suction appears reduced .
To wash your HEPA dust cup filter, hold filter cartridge by frame flange, flange side up
and rinse under water. When finished, shake off excess water. Do NOT wash in
dishwasher.
It is important that when you wash the HEPA dust cup filter, you allow it to dry
COMPLETELY before using it again. We recommend 24 hours to air dry. DO NOT
DRY IN DRYER.
IMPORTANT: The Pre-Motor filter, Pre-Filter and Post Motor filter should be replaced
every 6 months or sooner if required.
All filters should be checked regularly for signs of damage, preferable after each
cleaning task. The filters must be replaced immediately if they become damaged.
Always disconnect the vacuum from the electrical outlet when checking the filters.
Important:
This vacuum cleaner is equipped with a motor protective thermostat. If for some
reason your vacuum overheats, the thermostat will automatically turn the unit off.
Should this occur, unplug the vacuum from the wall outlet and turn off the switch.
Empty the dust cup, "TapClean" the dust cup filter and check for blockages in hose
and suction inlet. Allow the unit to cool for a minimum of 45 minimum prior to restarting
the unit. To restart, re-plug the vacuum into the wall socket and turn the switch back
on.
10 Printed in China