Shark S4601 Series User manual

S4601 Series
OWNER’S GUIDE

11-800-798-7398
WHEN USING YOUR SHARK®BLAST
& SCRUB STEAM POCKET®MOP,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK BLAST & SCRUB STEAM
POCKET MOP.
WARNING: DANGER OF SCALDING.
The steam emitted from the Steam Mop
is very hot and may cause scalding.
Please use caution when using the
Steam Mop.
WARNING: KEEP STEAM MOP AWAY
FROM CHILDREN.
POLARIZED PLUG:
This Steam Mop has a polarized plug (one
blade is wider than the other). As a safety
feature, this plug will fit into a polarized outlet
only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1.
CAUTION: When in use, never turn the
Steam Mop over or on its side. Never direct
steam toward people, pets, or plants.
2. Use the system only for its intended use.
3. DO NOT use for space-heating purposes.
4. DO NOT use outdoors.
5. DO NOT leave the Steam Mop unattended
when plugged in. Always unplug the power cord
from the electrical outlet when not in use and
beforeservicing.
6. DO NOT allow the Steam Mop to be used by
children. Close attention is necessary when
used near children, pets, or plants.
7. Use only as described in this manual.
8. Use only manufacturer’s recommended
accessories.
9. DO NOT use with damaged cord or plug. If
Steam Mop is not working as it should or has
been dropped, damaged, left outdoors, or
dropped into water, return it it to EURO-PRO
Operating LLC for examination and repair.
Incorrect re-assembly or repair can cause a risk
of electrical shock or injury to persons when the
Steam Mop is used.
10. To protect against a risk of electric shock, DO
NOT immerse the Steam Mop in water or any
other liquids.
11. DO NOT handle plug or Steam Mop with wet
hands or operate it without wearing shoes.

2www.sharkclean.com
12. DO NOT pull or carry by cord, use cord as
a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
Steam Mop over cord. Keep cord away from
heated surfaces.
13. DO NOT unplug by pulling on power cord. To
unplug, grasp the plug not the power cord.
Do not use extension cords or outlets with
inadequate current-carrying capacity.
14. DO NOT put any objects into the the Steam
Nozzle openings. Discontinue use if the steam
nozzle is blocked.
15. DO NOT put hands or feet under the Steam
Mop. It gets very hot.
16. Use ONLY on flat, horizontal surfaces. Do not
use on walls, counters, or windows.
17. DO NOT use on leather, wax-polished furniture,
synthetic fabrics, velvet, or other delicate,
steam-sensitive materials.
18. DO NOT add cleaning solutions, vinegar,
scented perfumes, oils, or any other chemicals
to the water used in this Steam Mop as this
may damage it or make it unsafe for use. If you
live in a hard-water area, we recommend using
distilled water in your Steam Mop.
19. Never leave any Pocket Pad in one spot
while using or storing for any period of
time, as this may damage your surfaces.
20. Carefully remove all Pocket Pads after you have
unplugged and allowed the Steam Mop to cool.
21. When cleaning the exterior of the Steam Mop ,
unplug the power cord from the electrical outlet
and clean with a dry or damp cloth. Do not pour
water or use alcohol, benzene, or paint thinner
on the Steam Mop .
22. Extreme caution should be exercised when
using the Steam Mop to clean stairs.
23. Keep your work area well lit.
24. Store Steam Mop indoors in a cool, dry place.
25. To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the
Steam Mop.
26. To avoid scalding injuries, always unplug and
allow the Steam Mop to cool before removing
or changing Mop Heads, Accessories, or Pocket
Pads.
WARNING: Your Steam Mop is
designed to clean hard-floor surfaces that will
withstand high heat. Do not use on unsealed
wood or unglazed ceramic floors. On surfaces
that have been treated with wax and on some
no-wax floors, the sheen may be removed
by the heat and steam action. It is always
recommended to test an isolated area of the
surface to be cleaned before proceeding. We
also recommend that you check the use and
care instructions from the floor manufacturer.
SAVE THESE
INSTRUCTIONS

31-800-798-7398
Thank you for purchasing the Shark®Blast & Scrub Steam Pocket®Mop.
This Owner’s Guide is designed to help you get a complete understanding of your new Steam Mop. Please read it
carefully and keep for future reference.
For a list of what is included with this model, refer to inside flap of box.
If you should have a question about your Shark®Blast & Scrub Steam Pocket®Mop, please call Shark Customer
Service at 1-800-798-7398.
REGISTER YOUR PURCHASE:
www.sharkclean.com
1-800-798-7398
RECORD THIS INFORMATION:
Model Number: ____________________________________
Date of Purchase (Keep receipt):_________________________
TECHNICAL SPECIFICATIONS:
Voltage: 120 V., 60 Hz
Watts: 1200W
Water Capacity: 550 ml (18 oz.)

4www.sharkclean.com
Contents
Getting Started............................................................................................... 5
Assembling Your Steam Mop .......................................................................... 6
Using Your Steam Mop ................................................................................... 7
Caring For Your Steam Mop ............................................................................ 9
Ordering Optional Accessories .......................................................................11
Troubleshooting Guide ...................................................................................12
Frequently Asked Questions...........................................................................13
Warranty.......................................................................................................14
Thank you for
purchasing the
Shark®Blast &
Scrub Steam
Pocket®Mop.

51-800-798-7398
Getting Started
When assembling your Steam Mop there may be a little water in or around the water tank. This is because we test all
our Steam Mops before you buy them, so you get a quality Shark Blast & Scrub Steam Pocket®Mop.
a Mop Handle
bQuick-Release Cord Holder
cCord Management Clip
dEngage Scrubber/ Release Head
eSteam Control Button
fWater Tank Lid
gWater Tank
hMop Body
iStain Scrubber
jSteam Nozzle
kRectangle Mop Head
lPocket Pad for Rectangle Head
mFilling Flask
a
f
g
i
d
k
l
m
LO HI
MED
b
e
h
c
j

6www.sharkclean.com
Assembling Your Steam Mop
fig. 1
fig. 2
WARNING: Always make sure the Steam Mop
is UNPLUGGED from the wall when not in use.
Never fill the Steam Mop, attach the Mop Head,
or change or remove the Pocket Pad when the
Steam Mop is plugged into the wall. Unplug from
the wall and allow to cool before you fill the
mop, attach or remove the mop head or change
or remove the cleaning pad. To prolong the
life of your Steam Mop, we recommend using
distilled water. Make sure you add only water
to the tank. Chemicals or cleaning solutions
(including vinegar) may damage the Steam Mop
and could be unsafe for you and your family.
STEAM MOP ASSEMBLY
1Insert the Mop Handle into the Mop Body (fig. 1).Push
the Mop Handle in until you hear it click into place.
2Select the Rectangle Mop Head and Pocket Pad. If
the Pocket pad is not already attached, fit one side
of the Pocket Pad onto the Mop Head first, then,
using the loop, pull the Pocket Pad over the Mop
Head. Attach the hook-and-loop fasteners on the top
of the Pocket Pad to secure it in place.
3Insert the Mop Head into the Mop Body. Push until
you hear it click into place (fig. 2).
4Attach the Blast & Scrub Pad to the hook-and-loop
surface of the Stain Scrubber (fig. 3).
5Pull up on the Water Tank Cap to open (fig. 4).
6Use the Filling Flask to pour water into the Water
Tank (fig. 5). Do not overfill. Press the Water Tank
Cap firmly to close it.
NOTE: Steps 2–6 also apply to the Triangle Mop Head.
NOTE: The Triangle Mop Head may not be included
with your product. See box for specific product details.
fig. 3
fig. 4
fig. 5

71-800-798-7398
NOTE: To prolong the life of your Steam Mop, we
recommend using distilled water.
NOTE: Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
1 Pull and twist the Quick-Release Cord Holder to
unwrap the power cord completely (fig. 6). Plug
into an electrical outlet.
2 The unit will be in Standby Mode as soon as it is
plugged in. The Standby Mode can be identified by a
blinking light around the Steam Control Button (fig. 7) .
3Press the Steam Control Button to select the LO,MED,
or HI Steam Setting
(fig. 7) . Press once for the LO
setting, twice for MED, three times for HI, and four
times to return to Standby Mode. Once in Standby
Mode, a light will blink around the Steam Control
Button, but all other Steam Setting Lights will be off.
4Clean your floors with a forward and backward motion.
5
When you come to a tough, dried-on floor stain, use
the Scrub Blast Mode to clean it away.
IMPORTANT: Make sure you do not use the Steam Mop without attaching a Pocket Pad and adding water
to the Water Tank first. When you are using the Steam Mop for the first time, it might take longer than
the normal 30 seconds to start steaming.
IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated
with wax and on some no-wax floors, the sheen may be removed by the heat and steam action. Test an
isolated area of the surface to be cleaned before proceeding. Check the use and care instructions from the
floor manufacturer.
Using Your Steam Mop
6 To engage the Scrub Blast Mode, slide the Engage
Scrubber/Release Head Button all the way down until you
hear a click (fig. 8). The Stain Scrubber will automatically
pop into position. Lift the Mop Body off the Mop Head and
place the Stain Scrubber on the floor to start scrubbing.
CAUTION: While in Scrub Blast Mode, do not
leave the Steam Mop stationary.
CAUTION: Do not Scrub any one area for an
extended period of time.
7 To go back to mopping, re-dock the Mop Body onto the
Mop Head. The Stain Scrubber will automatically retract.
8 When you are done mopping, press the Steam
Control Button until you return to Standby Mode.
9 When the Water Tank is empty, the Steam Mop will stop
producing steam. You can refill the Water Tank at any
time as long as the Steam Mop is unplugged. Follow the
Water Tank filling instructions on page 6.
NOTE: Please wait 2 to 3 minutes for the Steam
Mop to cool off before switching the Mop Head or
the Pocket Pad. Never leave the Steam Mop with a
damp/wet Pocket Pad on any floor.
fig. 6
fig. 7
LO HI
MED
fig. 8

8www.sharkclean.com
The Shark®Blast & Scrub Steam Pocket®Mop has 3 unique steam settings so you can use the right amount of
steam for the cleaning task at hand. See below for tips on when to use each setting.
SETTING IDEAL FOR THESE SURFACES RECOMMENDED USAGE
LO Laminate
Hardwood
Marble
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
Sanitizing floors
MED
Hardwood
Marble
Tile
Stone
Cleaning most surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate- and heavy-traffic areas
Sanitizing floors
HI Hardwood
Marble
Tile
Stone
Deep-cleaning and cleaning hard-to-clean surfaces
Tough cleaning and removing stuck-on messes and stains
Deep-cleaning heavy-traffic areas
Cutting through heavy dirt and grime
Sanitizing floors
SCRUB BLAST
LO
MED
HI
To engage the Scrub Blast Mode, slide the Engage Scrubber/Release Head Button down until
you hear a click. The Stain Scrubber will automatically pop in to position. Lift the Mop body off
the Mop Head and place the Stain Scrubber on the floor to start scrubbing. You can select you
preferred level of steam. Use the LO setting for low-moisture, MED for more dried-on messes,
and HI for stubborn, stuck-on stains.
TO SANITIZE* WITH THE RECTANGLE MOP HEAD
1Start with a clean Pocket Pad.
2Plug in the unit and press the Steam Control Button to select either the LO, MED or HI Setting.
3Wait 30 seconds for the unit to begin producing steam.
4 Start mopping on an appropriate sealed hard-floor surface with a forward and backward motion. After three minutes,
your unit is ready to be used to sanitize.
5Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 15 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
With Rectangle Mop Head only. Not in Blast & Scrub mode.

91-800-798-7398
AFTER USE AND STORAGE
1Press the Steam Control Button until the Steam Mop
returns to Standby Mode. Unplug the cord from the
outlet and place the Steam Mop into the upright
position. Let it cool.
2Remove the Pocket Pad from the Mop Head by
undoing the hook-and-loop closure and using the
loop on the side to pull it off the Mop Head, avoiding
contact with the hot Pocket Pad.
Caring for Your Steam Mop
fig. 9
3Empty the Water Tank before storing. Open the
Water Tank Cap and empty the Tank in a sink. Close
the Cap.
4 To store the Steam Mop hanging up, first remove
the Mop Head (after it has cooled and the steam
has been released), then hang on a large hook (not
included) (fig. 9).

10www.sharkclean.com
fig. 10 fig. 11
POCKET PAD CARE INSTRUCTIONS
Care
Before washing, close the hook-and-loop fasteners so they
won’t snag on the Pocket Pads. Machine wash the Pocket
Pads separately with warm water using liquid detergent.
NEVER USE BLEACH, POWDERED DETERGENT, OR
FABRIC SOFTENERS as they may damage or leave a
coating on the Pocket Pads that will reduce their cleaning
performance and absorbancy . Pocket Pads should be
line-dried or tumble-dried on a low setting, as this will
extend the life of the microfiber fabric (fig. 10).
Loose fibers can indicate wearing of the microfiber
fabric. Do not pull the loose fibers as this can cause the
weave to come undone. Simply trim the loose fibers with
scissors (fig. 11).
Replacement Pocket Pads
For best cleaning results, we recommend replacing your
Pocket Pads every 3 to 4 months following normal use.
As with any fabric, dirt particles, grease, friction, and
repeated washing can cause the fibers to break down, and
you may notice an increase in the effort needed to push or
pull the Steam Mop.
You can purchase replacement Pocket Pads and
Accessories by visiting www.sharkclean.com or calling
1-800-798-7398.
STEAM NOZZLE CARE
If you believe the Steam Nozzle or the Direct Steam
Nozzle is clogged, please contact Customer Service at
1-800-798-7398 or [e-mail].

11 1-800-798-7398
ACCESSORY
Triangle Mop Head
For cleaning corners and hard-to-reach areas (not for sanitization).
101SC4601
Rectangle Mop Head
For all-purpose cleaning.
100SC4601
XL Mop Head
For large-area cleaning (not for sanitization).
102SC4601
XL Rectangle All-Purpose Pocket Pad
Shaggy fingers on both sides lift and lock in dust and dirt.
P180W
Triangle Washable All-Purpose Scrub Pocket Pad
One side features scrubbing strips to help remove tough, dried-on stains;
the other features shaggy fingers to lift and lock in dust and dirt.
P179W
Rectangle Washable All-Purpose Scrub Pocket Pad
One side features scrubbing strips to help remove tough, dried-on stains;
the other features shaggy fingers to lift and lock in dust and dirt.
P139W
Stain Blast Blast & Scrub Pad
Breaks apart tough, dried-on stains fast.
P176W
NOTE: Select Accessories are included. Others are available for purchase at www.sharkclean.com or
by calling 1-800-798-7398.
For a list of what is included with this model, refer to inside flap of box.
Ordering Optional Accessories

12www.sharkclean.com
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Steam Mop isn’t
producing any steam.
The Steam Mop should be securely plugged into an electrical outlet. Check your fuse or
circuit breaker or try a different outlet.
Make sure the Water Tank is full, the unit is plugged in, and the light around the Steam
Control Button is solid.
If the light around the Steam Control Button is not lit, try a different electrical outlet.
If the light around the Steam Control Button is blinking, press the Steam Control Button
to select a Steam Setting.
If the light around the Steam Control Button is solid, wait 30 seconds for the unit to warm up.
If after following the above steps the Steam Mop still does not produce any steam,
contact Customer Service at 1-800-798-7398 or [email protected].
The Steam Mop is
producing intermittent
steam.
This is normal—for more consistent steam select the HI Setting.
Also make sure the Water Tank is full.
I can’t select a Steam
Setting.
Make sure the unit is plugged in and the light around the Steam Control Button is solid.
If your Steam Mop is producing steam but the light around the Steam Control Button is
not lit, call customer service at 1-800-798-7398.
I am getting streaky/
cloudy floors.
The Pocket Pad might be dirty. If it is, flip it over to the clean side or change it entirely.
If you washed the Pocket Pad with powdered detergent, then it could be damaged and
require replacement.
This could also be an indication of soap or grease residue that has accumulated on
the floor. As our Steam Mops use only a small amount of water, it may not be enough
to rinse off the accumulation of residue that the steam is bringing to the surface. We
suggest rinsing the floor with nothing but water, letting it dry, and then steam mopping
again with a clean Pocket Pad. One or more rinses will generally remove the residue.
A more stubborn case may require you to rinse the floor with a mix of one part vinegar and two
parts water* (but DO NOT put vinegar or any other cleaner into the Steam Mop’s Water Tank).
*Please consult your flooring manufacturer’s care and maintenance instructions before
applying any cleaning products or solutions including vinegar.
It’s really hard for me
to push/pull the Steam
Mop.
If you are using the Scrub side of the Pocket Pad, which is designed for stain and heavy
residue cleaning, you will feel more friction when using the Steam Mop.
The Steam Mop might also be hard to push/pull if the Pocket Pad isn’t wet enough. It
should get easier to push/pull the Steam Mop after it’s been running for a few minutes.
We also recommend using the Shaggy side of the Pocket Pad for an easier push/pull
experience when cleaning larger areas.
An overly dirty pad could also result in a harder push/pull experience. We recommend
flipping the pad over or using a clean pad.

13 1-800-798-7398
Frequently Asked Questions
QUESTION ANSWER
How do I deploy the Stain
Scrubber?
To deploy the Stain Scrubber, slide the Engage Scrubber/Release Head Button
all the way down until you hear a click. The Stain Scrubber will automatically
pop into position. Lift the Mop Body off the Mop Head and place it on the floor
to start scrubbing.
How do I retract the Stain
Scrubber?
Re-dock the Mop Body onto the Mop Head and the Stain Scrubber will
automatically retract.
Is the Stain Scrubber going to
damage my floors?
The Stain Scrubber is designed to be safe on all sealed floors, but it is always
recommended to test an isolated area of the surface to be cleaned before
proceeding.
Can I use the Steam Mop on
carpets? No, the Steam Mop is not designed for carpet cleaning.
What surfaces can I use the
Steam Mop on?
The Steam Mop is designed for use on all sealed hard-floor surfaces. We
recommend that you first test an isolated area of the floor surface to be cleaned
as well as review the use and care instructions from your floor manufacturer.
WARNING: Do not use on leather, wax-polished furniture, synthetic
fabrics, velvet, or other delicate, steam-sensitive materials.
NOTE: On surfaces treated with wax and on some no-wax floors, the sheen
may be removed by the heat or steam action of the unit. Test an isolated area of
flooring first to see if sheen is affected.
Can I put something other than
water in the Water Tank of the
Steam Mop?
DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals
to the water used in this appliance as this may damage the unit or make it
unsafe for use. We recommend using distilled water in your Steam Mop.

14www.sharkclean.com
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period
of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following
conditions, exclusions, and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period,
return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or
customer support, please call Customer Service at 1-800-798-7398 or visit www.sharkclean.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace
it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight.*
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our
option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with
or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent
handling, or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects
caused by or resulting from damages from shipping or repairs, service, or alterations to the product or any of its parts
that have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional
warranties. The responsibility of EURO-PRO Operating LLC warranty if any, is limited to the specific obligations
expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for
incidental or consequential damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or
province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date
and to attach tag to item before packing with your name, complete address, and phone number with a
note giving purchase information, model number, and what you believe is the problem with the item. We
recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the
outside of your package “ATTENTION CUSTOMER SERVICE”.
Product Registration
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark®product within ten (10) days of
purchase. You will be asked to provide the store name, date of purchase, and model number, along with your name and
address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering, you
acknowledge you have read and understood the instructions for use and the accompanying warnings set forth in the
instructions.

EURO-PRO Operating LLC U.S.: Newton, MA 02459 Canada: Ville St. Laurent, Québec H4S 1A7 1-800-798-7398 www.sharkclean.com
Questions or Problems?
CALL US.
We are here to
help with our
hassle-free
return service.
Toll-Free Customer Support Telephone:
Mon–Sat: 7am–11pm, Sun: 9am–8pm EST
1-800-798-7398
[e-mail]
COPYRIGHT © 2015 EURO-PRO OPERATING LLC Euro-Pro,Shark and Steam Pocket are registered trademarks of Euro-Pro Operating LLC. S4601_31_IB_E_150710_1 PRINTED IN CHINA. Illustrations may differ from actual product. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice. For Shark | Ninja U.S. Patent information, visit http://www.europro.com/USPatents