Sharp EL-2910R User manual

ELECTRONIC PRINTING CALCULATOR
DRUCKENDER TISCHRECHNER
CALCULATRICE IMPRIMANTE ÉLECTRONIQUE
CALCULADORA IMPRESORA ELECTRÓNICA
CALCOLATRICE ELETTRONICA STAMPANTE
ELEKTRONISK SKRIVANDE OCH VISANDE RÄKNARE
ELEKTRONISCHE REKENMACHINE MET AFDRUK OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
BRUKSANVISNING
GEBRUIKSAANWIJZING
ENGLISH ................................................... Page 1
CALCULATION EXAMPLES ..................... Page 63
DEUTSCH .................................................. Seite 10
RECHNUNGSBEISPIELE ......................... Seite 63
FRANÇAIS ................................................. Page 19
EXEMPLES DE CALCULS ........................ Page 63
ESPAÑOL .................................................. Página 28
EJEMPLOS DE CALCULOS ..................... Página 64
ITALIANO ................................................... Pagina 37
ESEMPI DI CALCOLO ............................... Pagina 64
SVENSKA .................................................. Sida 46
GRUNDLÄGGANDE RÄKNEEXEMPEL ... Sida 65
NEDERLANDS .......................................... Pagina 54
REKENVOORBEELDEN ........................... Pagina 65
EL-2910R

Notes for handling Lithium batteries:
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
Hinweise zur Handhabung von Lithium-Batterien:
VORSICHT
Bei Verwendung einer uneeigneten Ersatzbatterie
besteht Explosionsgefahr.
Nur durch den gleichen oder einen vom Hersteller
empfohlenen gleichwertigen Typ ersetzen.
Verbrauchte Batterien gemäß Herstelleranleitung
entsorgen.
Remarques sur la manipulation des piles au lithium:
ATTENTION
Danger d’explosion de la pile si elle n’est pas remplacée
correctement.
Remplacez-la uniquement par le même type de pile ou
un type équivalent recommandé par le fabricant.
Débarrassez-vous des piles usagers en respectant les
instructions du fabricant.
Notas para el manejo de las baterías de litio:
PRECAUCIÓN
Peligro de explosión si reemplaza incorrectamente la
batería.
Reemplácela por otra igual o de tipo equivalente
recomendada por el fabricante.
Deshágase de las baterías de acuerdo con las
instrucciones del fabricante.
Note concernenti le batterie al litio:
AVVERTENZA
Se la batteria non viene sostituita in modo corretto c’è
pericolo di esplosioni.
Sostituire la batteria con una dello stesso tipo o con una
equivalente raccomandata dalla fabbrica.
Smaltire le batterie usate seguendo le istruzioni della
fabbrica.
Observera om hantering av litiumbatterier:
OBSERVERA!
Felaktigt batteribyte medför risk för explosion.
Byt endast ut batteriet mot ett batteri av samma eller
motsvarande typ rekommenderat av tillverkaren.
Kassera ett förbrukat batteri enligt tillverkarens
anvisningar.
Opmerkingen betreffende de behandeling van
lithiumbatterijen:
LET OP
Ontploffingsgevaar indien de batterij verkeerd wordt
aangebracht.
Vervang uitsluitend door een batterij van hetzelfde of
een gelijkwaardig type, aanbevolen door de fabrikant.
Gooi gebruikte batterijen weg overeenkomstig de
instructies van de fabrikant.

1
CONTENTS
OPERATIONAL NOTES
ENGLISH
Page
• INSTALLING OF BATTERY FOR
MEMORY PROTECTION .................................. 2
• OPERATING CONTROLS ................................. 3
• PAPER ROLL REPLACEMENT ......................... 5
• INK ROLLER REPLACEMENT ......................... 5
• ERRORS ........................................................... 6
• REPLACEMENT OF BATTERY FOR
MEMORY PROTECTION .................................. 7
• SPECIFICATIONS ............................................. 8
• RESETTING THE UNIT ..................................... 9
• CALCULATION EXAMPLES............................ 63
• TAX RATE CALCULATIONS ........................... 73
To insure trouble-free operation of your SHARP
calculator, we recommend the following:
1. The calculator should be kept in areas free from
extreme temperature changes, moisture, and
dust.
2. A soft, dry cloth should be used to clean the
calculator. Do not use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it
or store it where fluids, for example water, can
splash onto it. Raindrops, water spray, juice,
coffee, steam, perspiration, etc. will also cause
malfunction.
4. If service should be required, use only a SHARP
servicing dealer, a SHARP approved service
facility or SHARP repair service.
5. If the unit is operated from AC power only, without
installing the memory protection battery, the set
tax rates and memory contents (including GT
memory) will be cleared if the power plug is
removed from the outlet. This will also occur when
the memory protection battery is replaced.

2
INSTALLING OF BATTERY FOR MEMORY PROTECTION
Before using for the first time, remove the attached
lithium battery, and install it in the equipment
according to the following procedure.
If the power cord is unplugged by accident when
operating with AC power only, the set tax rate and
the contents of memory will be lost.
1) Turn the power switch “OFF” and unplug the
power supply plug from the outlet.
2) Remove the battery cover on the back of the unit.
(Fig. 1)
3) Wipe the battery well with a dry cloth and place
the plus “+” side upward. (Fig. 2)
4) Replace the battery cover by reversing the
removal procedure.
5) Press the RESET switch on the back of the unit
(See page 9).
After battery installation
•Connect the power supply plug to an outlet and
turn the power switch “ON”.
Check that “0.” is displayed. If “0.” is not displayed,
remove the battery, reinstall it, and check the
display again.
•On the battery replacement date label found on
the back of the unit, write down the month and
year when the battery is installed, as a reference
for the next battery replacement.
Fig. 1 Fig. 2
1
2

3
OPERATING CONTROLS
OFF PICP
ON POWER SWITCH; PRINT / ITEM
COUNT MODE SELECTOR:
“OFF”: Power OFF
“•”: Power ON. Set to the non-print
mode.
“P”: Power ON. Set to the print
mode.
“P•IC”: Power ON. Set to the print
mode.
Each time or is
pressed, in the case of
additional and subtraction, or
or is pressed, in the
case of memory calculations,
the associated item counter is
incremented by one. Select the
“P•IC” position to print the
counter values.
• The count is printed when
the calculated result is
obtained.
• Pressing of ,
clears the counter.
Note: The counter has a maximum
capacity of 3 digits (up to
+999). If the count exceeds the
maximum, the counter will
recount from zero.
F 6 3 2 1 0 A
DECIMAL / ADD MODE SELEC-
TOR:
“F”: Floating.
“6 3 2 1 0”: Fixed.
“A”: Add mode.
ROUNDING SELECTOR:
“”: An answer is rounded up.
“5/4”: An answer is rounded off.
“”: An answer is rounded down.
GT RATE SET
GRAND TOTAL / RATE SETTING
MODE SELECTOR:
“GT”: This selector will accumulate the
following: (“ + ”will be printed.)
•Addition and subtraction totals
obtained with .
“•”: Neutral, GT OFF.
“RATE SET”: Set the key to position
to enter (or change) the
tax rate.

4
TAX-INCLUDING KEY
PRE-TAX KEY
DISPLAY SYMBOLS:
M : Memory symbol
Appears when a number is in the memory.
– : Minus symbol
Appears when a number is negative.
←: Error symbol
Appears when an overflow or other error is
detected.
PAPER FEED KEY
LAST DIGIT CORRECTION KEY
GRAND TOTAL KEY
NON-ADD KEY
SUBTOTAL KEY
CLEAR / CLEAR ENTRY KEY
TOTAL KEY
EQUAL KEY
CHANGE SIGN KEY:
Changes the algebraic sign of a number (i.e.,
positive to negative or negative to positive).
MARKUP KEY:
Used to perform mark-ups and mark-down.
RECALL AND CLEAR MEMORY KEY
RECALL MEMORY KEY
PERCENT CHANGE KEY

5
Never insert paper roll if torn. Doing so will cause
paper to jam. Always cut leading edge with
scissors first.
1) Insert the leading edge of the paper roll into the
opening. (Fig. 1)
2) Turn the power on and feed the paper by pressing
. (Fig. 2)
3) Lift the attached metal paper holder up and insert
the paper roll to the paper holder. (Fig. 3)
Fig. 3
Fig. 1
Fig. 2
PAPER ROLL REPLACEMENT
INK ROLLER REPLACEMENT
DO NOT PULL PAPER BACKWARDS AS THIS
MAY CAUSE DAMAGE TO PRINTING
MECHANISM.
If printing is blurry even when the ink roller is in the
proper position, replace the roller.
Ink roller: Type EA-781R-BK (Black)
Type EA-781R-RD (Red)
WARNING
APPLYING INK TO WORN INK ROLLER OR
USE OF UNAPPROVED INK ROLLER MAY
CAUSE SERIOUS DAMAGE TO PRINTER.
1) Set the power switch to OFF.
2) Remove the printer cover. (Fig. 1)
3) Remove the ink roller by turning it counterclockwise
and pulling it upward. (Fig. 2)
4) Install the correct color new ink roller and press it
in the correct position. Make sure that the ink roller
is securely in place. (Fig. 3)
5) Put back the printer cover.

6
Fig. 1 Fig. 2
Fig. 3
ERRORS
Red Black
Cleaning the printing mechanism
If the print becomes dull after long time usage,
clean the printing wheel according to the
following procedures:
1) Remove the printer cover and the ink roller.
2) Install the paper roll and feed it until it comes out
of the front of the printing mechanism.
3) Put a small brush (like a tooth brush) lightly to the
printing wheel and clean it by pressing .
4) Put back the ink roller and the printer cover.
Notes: •Do not rotate the printing mechanism
manually, this may damage the printer.
•Never attempt to turn the printing belt or
restrict its movement while printing. This
may cause incorrect printing.
There are several situations which will cause an
overflow or an error condition. When this occurs, “←”
will be displayed. The contents of the memory at the
time of the error are retained.
If “←”is displayed at the time of the error,
“•••••••••••••••••” will be printed in black and must
be used to clear the calculator.
Error conditions:
1. When the integer portion of an answer exceeds
12 digits.
2. When the integer portion of the contents of the
memory exceeds 12 digits.
(Ex. 999999999999 1 )
3. When any number is divided by zero. (Ex. 5 0
).

7
4. This unit is equipped with a key input buffer (12
row max.), and it may give an error message if
you exceed the buffer limit by pressing keys
sequentiallly during printing.
Time for battery replacement
Replace with a new battery once 2 year.
Method of battery replacement
Use one lithium battery (CR2032).
Note: When replacing the battery, the set tax rate
and the memory contents will be lost.
You may want to write down the tax rate and
other important numbers on a sheet of paper.
1) Turn the power switch “OFF”and unplug the
power supply plug from the outlet.
2) Remove the battery cover on the back of the unit.
(Fig. 1)
3) Remove the exhausted battery and install one
new lithium battery. Wipe the battery well with a
dry cloth and place the plus “+”side upward. (Fig.
2)
4) Replace the battery cover by reversing the
removal procedure.
5) Press the RESET switch on the back of the unit
(See page 9).
After battery replacement
•Connect the power supply plug to an outlet and
turn the power switch “ON”.
Check that “0.”is displayed. If “0.”is not displayed,
remove the battery, reinstall it, and check the
display again.
•Reset the tax rate.
•On the battery replacement date label found on
the back of the unit, write down the month and
year when the battery is replaced, as a reference
for the next battery replacement.
REPLACEMENT OF BATTERY FOR MEMORY PROTECTION
Fig. 1 Fig. 2
1
2

8
Precautions on battery use
•Do not leave an exhausted battery in the
equipment.
•Do not expose the battery to water or flame, and
do not take it apart.
•Store batteries out of the reach of small children.
Operating capacity: 12 digits
Power supply: Operating:
AC: 220V-230V, 50Hz
Memory backup:
3V ... (DC)
(Lithium battery CR2032 ×
1)
Memory Protection Battery lifespan:
Approx. 2 years. (tested
and confirmed at 25°C
(77°F); may change due to
usage environment)
PRINTING SECTION
Printer: Mechanical printer
Printing speed: Approx. 3.0 lines/sec.
Printing paper: 57 mm (2-1/4”) –58 mm (2-
9/32”) wide
80 mm (3-5/32”) in
diameter (max.)
Operating temperature: 0°C –40°C (32°F –104°F)
Power consumption: 74 mA
Dimensions: 221 mm (W) ×305 mm (D)
×72 mm (H)
(8-11/16”(W) ×12-1/16”
(D) ×2-27/32”(H))
Weight: Approx. 1.3 kg (2.87 lb.)
(with battery)
Accessories: 1 lithium battery, 1 battery
replacement date label
(attached on the unit’s
back body), 1 paper roll, 2
ink rollers (installed), and
operation manual
SPECIFICATIONS