Sharp CD-BP99V User manual

OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
SHARP CORPORATION
MODEL
MODÈLE
MODELO
CD-BP99V
VIDEO CD MINI SYSTEM
MINI-CHAÎNE CD VIDÉO
SISTEMA MINI VÍDEO CD
NTSC/PAL
CD-BP99V Video CD Mini System consisting of CD-BP99V (main unit) and CP-BP99
(speaker system).
Mini-chaîne CD vidéo CD-BP99V composée de CD-BP99V (appareil principal) et de CP-
BP99 (enceintes acoustiques).
Sistema mini vídeo CD CD-BP99V que consta de CD-BP99V (aparato principal) y CP-
BP99 (sistema de altavoces).
CD-BP99V CD-BP99V CP-BP99
Please refer to pages E-1 to E-33.
Se reporter aux pages F-1 à F-33.
Consulte las páginas S-1 a S-33.
ENGLISH
FRANÇAIS
ESPAÑOL
Downloaded from: http://www.usersmanualguide.com/

E-1
01/7/13 CD-BP99V(X)E1.fm
ENGLISH
CD-BP99V
ENGLISH
Important Instruction
- Introduction / Contents -
Introduction
Thank you for purchasing this SHARP product. To obtain the best performance from
this product, please read this manual carefully. It will guide you in operating your
SHARP product.
Contents
Page
!Important Instruction
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Special notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
!General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6
!Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 9
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
!Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
!Video CD Playback
Video CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Preparation for video CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13
Playback of a video CD (CDs) with P. B. C. (Version 2.0) . . . . . . . . . . . . . . . 14, 15
Playback of a video CD (CDs) without P. B. C. (Version 1.1) . . . . . . . . . . . . 16, 17
!Advanced Video CD (Version 1.1) Playback
Programmed play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Repeat or random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Time search selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Digest selection of discs and tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Bookmark function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
To play back the video CD manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing the TV screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Page
!CD Playback
Listening to a CD (CDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 24
!Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Listening to the memorised station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
!Tape Playback
Listening to a cassette tape (TAPE 1 or TAPE 2) . . . . . . . . . . . . . . . . . . . . . . . . 27
!Tape Recording
Recording to a cassette tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29
!Advanced Features
Timer and sleep operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 31
!References
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Downloaded from: http://www.usersmanualguide.com/

E-2
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
Important Instruction
- Accessories / Special notes -
Accessories
Please confirm that the following accessories are included.
Note:
Only the above accessories are included.
Special notes
Warning:
"When the ON/STAND-BY button is set at STAND-BY position, mains voltage is still
present inside the unit. When the ON/STAND-BY button is set at STAND-BY posi-
tion, the unit may be brought into operation by the timer mode or remote control.
"This unit contains no user serviceable parts. Never remove covers unless qualified
to do so. This unit contains dangerous voltages, always remove mains plug from
the socket before any service operation and when not in use for a long period.
"To prevent fire or shock hazard, do not expose this appliance to dripping or splash-
ing. No objects filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION
Note:
Audio-visual material may consist of copyrighted works which must not be recorded
without the authority of the owner of the copyright. Please refer to the relevant laws in
your country.
Remote control 1 "AA" size battery (UM/
SUM-3, R6, HP-7 or
similar) 2
AM loop aerial 1 FM aerial 1 Video cable 1 AC power lead 1
"This product is classified as a CLASS 1 LASER product.
"Use of controls, adjustments or performance of procedures other than those spec-
ified herein may result in hazardous radiation exposure.
As the laser beam used in this compact disc player is harmful to the eyes, do not
attempt to disassemble the cabinet. Refer servicing to qualified personnel only.
Laser Diode Properties
Material: GaAIAs
Wavelength: 780 nm
Emission Duration: continuous
Laser Output: max. 0.6 mW
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN.
DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS.
WARNUNG-UNSICHTBARE LASERSTRAHLUNG WENN GERÄT
GEÖFFNET. NICHT IN DIE STRAHLUNG SCHAUEN ODER
DIREKT MIT OPTISCHEN HILFSMITTELN BETRACHTEN.
ATTENTION-RAYON LASER INVISIBLE EN CAS D’OUVERTURE.
NE PAS REGARDER LE FAISCEAU DIRECTEMENT OU AVEC DES
INSTRUMENTS OPTIQUES.
Downloaded from: http://www.usersmanualguide.com/

E-3
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
General Information
- Precautions -
Precautions
!General
"Please ensure that the equipment is positioned in a well-ventilated area and
ensure that there is at least 10 cm (4") of free space along the sides, top and back
of the unit.
"Use the unit on a firm, level surface free from vibration.
"Keep the unit away from direct sunlight, strong magnetic fields, excessive dust,
humidity and electronic/electrical equipment (home computers, facsimiles, etc.)
which generates electrical noise.
"Do not place anything on top of the unit.
"Do not expose the unit to moisture, to temperatures higher than 60°C (140°F) or to
extremely low temperatures.
"If your system does not work properly, disconnect the AC power lead from the wall
socket. Plug the AC power lead back in, and then turn on your system.
"In case of an electrical storm, unplug the unit for safety.
"Hold the AC power plug by the head when removing it from the wall socket, as
pulling the lead can damage internal wires.
"Do not remove the outer cover, as this may result in electric shock. Refer
internal service to your local SHARP service facility.
"The ventilation should not be impeded by covering the ventilation openings with
items, such as newspapers, tablecloths, curtains, etc.
"No naked flame sources, such as lighted candles, should be placed on the appa-
ratus.
"Attention should be drawn to the environmental aspects of battery disposal.
"This unit should only be used within the range of 5°C - 35°C (41°F - 95°F).
Warning:
The voltage used must be the same as that specified on this unit. Using this product
with a higher voltage other than that which is specified is dangerous and may result in
a fire or other type of accident causing damage. SHARP will not be held responsible
for any damage resulting from use of this unit with a voltage other than that which is
specified.
!Volume control
The sound level at a given volume setting depends on speaker efficiency, location,
and various other factors. It is advisable to avoid exposure to high volume levels,
which occurs whilst turning the unit on with the volume control setting up high, or
whilst continually listening at high volumes.
!Condensation
!Care of compact discs
Compact discs are fairly resistant to damage, however mistracking can occur due to
an accumulation of dirt on the disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
"Do not write on either side of the disc, particularly the non-label side from which
signals are read. Do not mark this surface.
"Keep your discs away from direct sunlight, heat, and excessive moisture.
"Always hold the CDs by the edges. Fingerprints, dirt, or water on the CDs can
cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a
soft, dry cloth, wiping straight out from the centre, along the radius.
10 cm (4")
10 cm (4") 10 cm (4")
10 cm (4") Sudden temperature changes, storage or opera-
tion in an extremely humid environment may
cause condensation inside the cabinet (CD pick-
up, tape heads, etc.) or on the transmitter on the
remote control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc
(or cassette) in the unit until normal playback is
possible (about 1 hour). Wipe off any condensa-
tion on the transmitter with a soft cloth before op-
erating the unit.
NO YES
Correct
Downloaded from: http://www.usersmanualguide.com/

E-4
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
General Information
- Controls and indicators -
Controls and indicators
!Display
1.Disc Number Indicators
2.Timer Indicator
3.Tape 2 Record Indicator
4.Sleep Indicator
5.Extra Bass Indicator
6.Disc or Tuner Memory Indicator
7.FM Stereo Mode Indicator
8.FM Stereo Receiving Indicator
9.Disc Repeat Play Indicator
10.Disc or Tape Play Indicator
11.Disc Pause Indicator
!Front panel Reference page
1.Disc Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.Timer Set Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . . 14, 16, 23
6.Disc Skip Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 16, 23
7.Equalizer Mode Select/Extra Bass/Demo Mode Button . . . . . . . . . 10
8.Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . 27,29
9.Tape 1 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . 27,29
10.Video CD/CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 16, 23
11.Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
12.Audio Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
13.Video CD Playback Control Button . . . . . . . . . . . . . . . . . . . . . . . . . 15
14.Video CD On Screen Display On/Off Button . . . . . . . . . . . . . . . . . . 22
15.Video CD Digest/Time Search Button . . . . . . . . . . . . . . . . . . . . 19, 20
16.Tuning and Time Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 25
17.Clock Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 30
18.Timer/Sleep Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 31
19.Headphone Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
20.Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 29
21.Video CD Stop or Return, CD/Tape Stop Button . . . . . 15, 16, 24, 27
22.Video CD Play or Repeat or Select or Resume, CD Play or Repeat,
Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . 14, 16, 19, 22, 23, 27
23.Tuning and Time Down Button . . . . . . . . . . . . . . . . . . . . . . . . . 11, 25
24.Video CD Skip or Previous, CD Track Down or Fast Reverse,
Tape 2 Rewind, Tuner Preset Down Button . . . . . . 15, 17, 24, 26, 27
25.Memory/Set Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 18, 26
26.Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29
27.Video CD Skip or Next, CD Track Up or Fast Forward,
Tape 2 Fast Forward, Tuner Preset Up Button . . . . 15, 17, 24, 26, 27
8
9
1
2
3
45
6
7
18
2523
17
13 14 15121110
16
27
24 26
19
20
21
22
123 4 5 6 78
11109
Description of remote control (See page 6.)
Downloaded from: http://www.usersmanualguide.com/

E-5
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
General Information
- Controls and indicators -
Controls and indicators (continued)
!Rear panel Reference page
1.Video Output Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.AC Power Input Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 8
3.Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 8
4.Span Selector Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5.AM Loop Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
6.FM Aerial Earth Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
7.FM 75 Ohms Aerial Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
!Speaker system
1.Full-Range Speaker
2.Bass Reflex Duct
3.Speaker Wire
Note:
The speaker grille is not removable.
!Placing the speaker system
2
1
2
3
21 56743
There is no distinction between the right
and the left speakers. Left speaker Right speaker
Notes:
"The speakers are magnetically shielded.
Therefore, they do not affect the display even you use them near the TV. However,
some colour variation may occur, depending on the type of TV used.
If colour variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
If the colour variation is still present...
Move the speakers further away from the TV.
"If any kind of magnet or an electromagnet is placed too close to the TV and the sys-
tem, irregular colours may appear on the TV screen.
Downloaded from: http://www.usersmanualguide.com/

E-6
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
General Information
- Controls and indicators -
!Remote control Reference page
1.Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.Audio Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.Video CD Auto/On Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.Video CD Playback Control Auto/Off Button . . . . . . . . . . . . . . . . . . . . 15
5.Video CD On Screen Display On/Off Button . . . . . . . . . . . . . . . . . . . . 22
6.Video CD Digest/Time Search Button . . . . . . . . . . . . . . . . . . . . . . 19, 20
7.Disc Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.Video CD Bookmark Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9.PAL/NTSC Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
10.Video CD Skip or Previous, CD Track Down or Fast Reverse,
Tape 2 Rewind, Tuner Preset Down Button . . . . . . . . . 15, 17, 24, 26, 27
11.Video CD/CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 16, 23
12.Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 29
13.On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14.Disc Direct Search Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 17
15.Disc Skip Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 16, 23
16.Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
17.Disc Memory Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
18.Video CD Skip or Next, CD Track Up or Fast Forward,
Tape 2 Fast Forward, Tuner Preset Up Button . . . . . . 15, 17, 24, 26, 27
19.Disc Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16, 24
20.Video CD Play or Repeat or Select or Resume, CD Play or Repeat,
Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 16, 19, 22, 23, 27
21.Video CD Stop or Return, CD/Tape Stop Button . . . . . . . . 15, 16, 24, 27
22.Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
23.Equaliser Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
24.Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
25.Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29
26.Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1
2
14
16
15
17
19
18
20
24
6
3
4
5
7
8
9
10
25
13
22
21
23
26
12
11
Buttons with " " mark in the illustration can be operated on the remote control
only.
Other buttons can be operated both on the main unit and the remote control.
Battery installation for remote control (See page 9.)
Downloaded from: http://www.usersmanualguide.com/

E-7
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
Preparation for Use
- System connections -
System connections
!Aerial connection
Note:
Placing the aerial on the unit or near the AC power lead may cause noise pickup.
Place the aerial away from the unit for better reception.
Installing the AM loop aerial:
External FM aerial:
Use an external FM aerial if you require better reception. Consult your dealer.
Note:
When an external FM aerial is used, disconnect the supplied FM aerial wire.
TV/monitor (See page 12.)
FM aerial
Left speaker
Right speaker
AM loop aerial
To the wall socket
(See page 8.)
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS
terminal and position the FM aerial wire in the
direction where the strongest signal can be re-
ceived.
Supplied AM loop aerial:
Connect the AM loop aerial wire to the AM
LOOP socket. Position the AM loop aerial for
optimum reception. Place the AM loop aerial on
a shelf, etc., or attach it to a stand or a wall with
screws (not supplied).
< Assembling > < Attaching to the wall >
Wall Screws (not supplied)
External
FM aerial
75 ohm
coaxial cable
Downloaded from: http://www.usersmanualguide.com/

E-8
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
Preparation for Use
- System connections -
!Speaker connection
Connect the black wire to the minus (-) terminal, and the red wire to the plus (+) ter-
minal.
Caution:
!Connecting the AC power lead
After making all connections, connect the AC power lead to the unit
and then into the wall socket. If you plug in the unit first, it will enter
the demonstration mode.
Notes:
"Unplug the AC power lead from the AC socket if the unit will not be in use for a pro-
longed period of time.
"Never use a power lead other than the one supplied. Use of a power lead
other than the one supplied may cause an electric shock or fire.
AC Plug Adaptor
In areas (or countries) where an AC socket as shown in illustration is used, con-
nect the unit using the AC plug adaptor supplied with the unit, as illustrated. The AC
plug adaptor is not included in areas where the AC wall socket and AC power plug
can be directly connected (see illustration ).
!Headphones
Right speaker Left speaker
"Use speakers with an impedance of 3 ohms or more, as lower impedance speakers
can damage the unit.
"Do not mistake the right and the left channels. The right
speaker is the one on the right side when you face the
unit.
"Do not let the bare speaker wires touch each other.
"Do not allow any objects to fall into or to be placed in the
bass reflex ducts.
"Do not stand or sit on the speakers. You may be injured. Incorrect
Black
Red
"Before plugging in or unplugging the headphones, reduce
the volume.
"Be sure your headphones have a 3.5 mm (1/8") diameter
plug and are between 16 ohms and 50 ohms impedance.
The recommended impedance is 32 ohms.
"Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME but-
tons.
1
2
Demonstration mode (See page 10.)
Downloaded from: http://www.usersmanualguide.com/

E-9
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
Preparation for Use
- System connections / Remote control -
System connections (continued)
!Setting the FM/AM span selector
The International Telecommunication Union (ITU) has established that member coun-
tries should maintain either a 100 kHz or a 50 kHz interval between broadcasting fre-
quencies of FM stations and 10 kHz or 9 kHz for AM station. The illustration shows
the 50/9 kHz zones (regions 1 and 3), and the 100/10 kHz zone (region 2).
Before using the unit, set the SPAN SELECTOR switch (on the rear panel) to the
interval (span) of your area.
To change the tuning zone:
Caution:
This operation will erase all data stored in memory including clock, timer settings,
tuner preset, and CD programme.
Remote control
!Battery installation
Precautions for battery use:
"Replace all old batteries with new ones at the same time.
"Do not mix old and new batteries.
"Remove the batteries if the unit will not be used for long periods of time. This will
prevent potential damage due to battery leakage.
Caution:
"Do not use rechargeable batteries (nickel-cadmium battery, etc.).
"Installing the batteries incorrectly may cause the unit to malfunction.
Notes concerning use:
"Replace the batteries if the operating distance is reduced or if the operation
becomes erratic. Purchase 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
"Periodically clean the transmitter on the remote control and the sensor on the unit
with a soft cloth.
"Exposing the sensor on the unit to strong light may interfere with operation.
Change the lighting or the direction of the unit.
"Keep the remote control away from moisture, heat, shock, and vibrations.
!Test of the remote control
1 Press the ON/STAND-BY button to enter the stand-by mode.
2 Set the SPAN SELECTOR switch (on the rear panel) as follows.
"For 50 kHz FM interval (9 kHz in AM) 50/9
"For 100 kHz FM interval (10 kHz in AM) 100/10
3 Whilst pressing down the / button and the EQUALIZER/X-BASS/DEMO but-
ton, press the ON/STAND-BY button until "CLEAR AL" appears.
1 Remove the battery cover.
2 Insert the supplied batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them towards the battery termi-
nals.
3 Replace the cover.
Face the remote control directly to the remote
sensor on the unit.
The remote control can be used within
the range shown:
Press the ON/STAND-BY button. Does the pow-
er turn on? Now, you can enjoy the music.
Remote sensor
0.2 m - 6 m
(8" - 20')
Downloaded from: http://www.usersmanualguide.com/

E-10
CD-BP99V(X)E1.fm01/7/13
ENGLISH
CD-BP99V
Basic Operation
- General control -
General control
!Demonstration mode
To cancel the demonstration mode:
When the unit is in the power stand-by mode (demonstration mode), press the
EQUALIZER/X-BASS/DEMO button. The demonstration mode will be cancelled and
the display will disappear.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the EQUALIZER/X-BASS/DEMO
button again.
Note:
When the power is on, the EQUALIZER/X-BASS/DEMO button can be used to select
the extra bass mode.
!To turn the power on
Press the ON/STAND-BY button to turn the power on.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
!Volume control
Press the VOLUME button to increase the volume and the VOLUME button for
decreasing.
!Extra bass (X-BASS)/Pre-programmed
equaliser
(Main unit operation)
You can select the extra bass and pre-programmed equaliser modes with the same
button on the main unit.
Changing the mode:
When the EQUALIZER/X-BASS/DEMO button is pressed, the current mode setting
will be displayed. To change to a different mode, press the EQUALIZER/X-BASS/
DEMO button repeatedly until the desired sound mode appears.
(Remote control operation)
To enter or cancel the extra bass mode:
When the power is first turned on, the unit will enter the extra bass mode which
emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra
bass mode, press the X-BASS button.
Selecting a pre-programmed equaliser mode:
When the EQUALIZER MODE button is pressed, the current mode setting will be dis-
played. To change to a different mode, press the EQUALIZER MODE button repeat-
edly until the desired sound mode appears.
The first time the unit is plugged in, the unit will enter
the demonstration mode. You will see words scroll.
012 29 30 MAXIMUM
.....
FLAT (X-BASS on)
ROCK (X-BASS on)
POPS (X-BASS on)
JAZZ (X-BASS on)
CLASSIC (X-BASS on)
VOCAL (X-BASS on)
VOCAL (X-BASS off)
CLASSIC (X-BASS off)
JAZZ (X-BASS off)
POPS (X-BASS off)
ROCK (X-BASS off)
FLAT (X-BASS off)
FLAT
ROCK
POPS
JAZZ
CLASSIC
VOCAL
The sound is not modified.
Bass and treble are emphasised.
Bass and treble are slightly emphasised.
Treble is cut a little.
Treble is reduced a lot.
Vocals (midrange tones) are emphasised.
Downloaded from: http://www.usersmanualguide.com/

E-11
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Basic Operation
- Setting the clock -
Setting the clock
In this example, the clock is set for the 24-hour (0:00) display.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from the beginning. If the time display is flashing, step 3
(for selecting the 24-hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1Press the ON/STAND-BY button to turn the power on.
2Press the CLOCK button and within 5 seconds, press the MEMO-
RY/SET button.
3Press the TUNING/TIME ( or ) button to select 24-hour or 12-
hour display and then press the MEMORY/SET button.
"0:00" The 24-hour display will appear.
(0:00 - 23:59)
"AM 12:00" The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00" The 12-hour display will appear.
(AM 0:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
[Refer to "Clearing all the memory (reset)" on page 32 for details.]
4Press the TUNING/TIME ( or ) button to adjust the hour and then
press the MEMORY/SET button.
!Press the TUNING/TIME ( or ) button once to advance the time by 1 hour.
Hold it down to advance continuously.
!When the 12-hour display is selected, "AM" will change automatically to "PM".
5Press the TUNING/TIME ( or ) button to adjust the minutes and
then press the MEMORY/SET button.
!Press the TUNING/TIME ( or ) button once to advance the time by 1
minute. Hold it down to change the time in 5-minute intervals.
!The hour will not advance even if minutes advance from "59" to "00".
!The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
To confirm the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on
page 32 for details.]
2 Perform "Setting the clock" from the beginning.
Downloaded from: http://www.usersmanualguide.com/

E-12
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Video CD Playback
- Video CD / Preparation for video CD playback -
Video CD
Any CD that contains motion pictures can be played.
You can enjoy motion pictures with the sound quality of MDs and the picture quality of
VHS tapes.
Digital compression technology allows the continuous playback of up to 74 minutes
from a 12 cm disc.
With video CDs, you can select the items you want to watch from the on-screen
menu. Discs which support "Playback control" can display still pictures. (See pages
14 - 15.)
The disc symbols are found on the disc labels or jackets.
"Types of discs
This unit handles video CDs that support PBC (version 2.0). (PBC is an abbreviation
of "Playback control".)
You can enjoy the following two types of playback, depending on the disc.
Notes:
!Video CDs are recorded in PAL or NTSC format.
!Analogue system CDVs (12 cm) cannot be played.
!Photo CDs and CD-ROMs cannot be played.
Preparation for video CD play-
back
"Connecting the TV/monitor
If the TV/monitor has a video input, connect it to VIDEO OUT socket on the rear of
the unit.
Note:
If the TV/monitor does not have a video input, the VIDEO OUT socket on the unit
should be connected to a VCR with a video input, which in turn should be connected
to the TV/monitor through the TV ANTENNA/CABLE input. (Be sure to turn on the
VCR, and set the VCR's input mode to "auxiliary".)
"Adjusting the TV and VCR
The TV and VCR input varies according to connection method. Be sure to make the
settings correctly. (Then, follow the playback procedure on pages 14 - 15 to check the
settings.)
Symbol
Size 8 cm (3") 12 cm (5")
Label sides 1 side 1 side
Audio recording format Digital (max. 20 min) Digital (max. 74 min)
Video recording format MPEG 1
Disc type Features
Video CDs without PBC
(version 1.1) Sound and motion pictures can be played using the same control operations as applied to music
CDs.
Video CDs with PBC
(version 2.0) In addition to the features shown above (for discs without PBC), PBC CDs have a menu that is dis-
played on the TV screen. You can play interactive
games and make use of other software with the
retrieval function (menu playback). You can also
display high resolution or normal still pictures.
TV/monitor
To video
input socket
Video cable
VCR
TV
Set the input selector
to AUX.
Set the TV/VCR selector
to VCR.
Set the input selector
to VCR.
<For TV sets with a video input socket>
<For TV sets without a video input socket>
Downloaded from: http://www.usersmanualguide.com/

E-13
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Video CD Playback
- Preparation for video CD playback -
Preparation for video CD playback (continued)
"Selecting the video output format
Video CD is recorded in PAL or NTSC format.
Select the video output format (NTSC, PAL or PAL 60) according to your TV or VCR.
To select the video output format:
Whilst in the stop mode, press the PAL/NTSC button.
Each time this button is pressed, the format will change in the following order:
Notes:
!Video CDs are recorded in PAL or NTSC format. When you watch a PAL disc in
the NTSC mode or an NTSC disc in the PAL mode, the vertical size of the picture
will not be modified.
!If a multi-mode TV is equipped with an input selector switch, set the switch to
"MULTI MODE". For the details, refer to the TV operation manual.
!Do not change the video output format during playback. If you do, the picture sig-
nal may not be output properly.
!Picture may be distorted when the setting is switched. This is not the malfunction
of the unit.
!A few hours after the unit is unplugged, the setting will be reset to PAL (factory set-
ting).
"To change the audio mode
Sound of the playback source can be switched among the STEREO, L-CH, and R-
CH modes.
The audio mode function is used when the left and right channels have individual sig-
nals from each other.
Press the AUDIO MODE button until the desired audio mode is dis-
played.
Each time the AUDIO MODE button is pressed, the mode will change as follows:
Notes:
!The initial audio mode setting is "STEREO".
!The setting will remain unchanged when you change the disc, you set the unit to
the stand-by mode or the function is changed from the CD/VIDEO CD (CD) to
another function.
!When playing a sound multiplexed disc on which a vocal and music have been
separately recorded, select the audio mode as desired.
PAL 60 NTSC PAL
STEREO Sounds on the left and right channels are played.
L-CH Sounds on the left channel only are played.
R-CH Sounds on the right channel only are played.
STEREO L-CH R-CH
Downloaded from: http://www.usersmanualguide.com/

E-14
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Video CD Playback
- Playback of a video CD (CDs) with P. B. C. (Version 2.0) -
Playback of a video CD (CDs) with P. B. C. (Version 2.0)
Playback control:
Video CDs that support "Playback control" can display still pictures. This function can
be used with video CD software (video CDs with playback control) that have a play-
back method recorded on them. You can select items you want to watch from the
menu displayed on the TV screen, or you can show still pictures.
Continued to the next page
1Turn on the TV and set the input selector to "VCR".
2Press the ON/STAND-BY button to turn the power on.
3Press the CD/VIDEO CD (CD) button.
4Press the OPEN/CLOSE button to open the disc tray.
5Place the video CD(s) with P.B.C. on the disc tray, label side up.
When loading a third disc, press the DISC SKIP button to turn the
disc tray, then place the video CD in the open position.
!Video CDs can be placed in any open position in the disc tray.
!Be sure to place 8 cm (3") Video CD(s) in the middle of the disc positions.
6Press the OPEN/CLOSE button to close the disc tray.
Total number of tracks on the
video CD whose number is flashing Total playing time of the video CD whose number is flashing
7To select the video CD you want to listen to first, press the DISC
SKIP button.
8Press the / ( /SELECT/RESUME) button.
A menu will appear on the TV and playback will be
paused.
12 cm (5") 8 cm (3")
1
2
<TV screen>
General control (See page 10.)
Downloaded from: http://www.usersmanualguide.com/

E-15
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Video CD Playback
- Playback of a video CD (CDs) with P. B. C. (Version 2.0) -
Playback of a video CD (CDs) with P. B. C. (Version 2.0) (continued)
To interrupt playback:
Press the button on the remote control.
To resume playback from the same point, press the /SELECT/RESUME button.
To stop the current operation and return to the menu:
Press the ( /RETURN) button for less than 0.5 seconds.
To completely stop the video CD:
Hold down the ( /RETURN) button for more than 1 second.
To remove the video CDs:
Whilst in the stop mode, press the OPEN/CLOSE button.
The disc tray will open. Remove the two discs. Then, press the DISC SKIP button to
rotate the disc tray and remove the remaining disc.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
Notes:
!Playback control allows a video CD to be played back according to instructions
recorded on the disc. The "previous", "next", "return" and "select" operations may
function differently, depending on the PBC CDs.
!Some video CDs with playback control may have an "auto pause" recorded on
them. When such a disc is played, the screen will stop automatically at the point
where an "auto pause signal" has been inserted.
!If the picture looks dirty when a video CD is played back, there may be a scratch
on the video CD. Replace it with another video CD in good condition.
The P.B.C. function will not work in the following conditions.
!When repeat, random, programme, bookmark, resume, disc digest, track digest or
time search play has been selected and playback begins.
!When track numbers are selected using the direct search, the / (NEXT )
or / ( PREV.) button, and playback begins.
"To move the menu screen (menu screen
with more than 1 page)
Notes:
!This function may not work, depending on the disc.
!The PREV. or NEXT button on the remote control allows you to locate the
desired portion.
"To play without activating the playback
control function
You can play a video CD with P.B.C. without activating the playback control function.
In this case, the menu screen will not appear, and the disc will be played in the same
way as a video CD without P.B.C.
Notes:
!The P.B.C. function can also be cancelled whilst in the playback mode.
!Some video CDs with P.B.C. cannot be played back when the P.B.C. mode is off.
!See pages 16 - 22 to perform various playback functions without activating the
P.B.C. function.
9Select the desired menu number using the direct search buttons
on the remote control.
!Playback will begin.
!After playback has finished, the menu will reappear. Select the menu number
you want to play.
To move to the next menu screen:
Whilst in the stop mode, press the / button.
To return to the previous menu screen:
Whilst in the stop mode, press the / button.
1Whilst in the stop mode, press the P.B.C. (P.B.C. AUTO/OFF) but-
ton to cancel the P.B.C. mode.
The P.B.C. function cannot be cancelled whilst the menu screen is displayed.
2Press the / ( /SELECT/RESUME) button.
Playback will begin.
PBC OFF
<TV screen>
Downloaded from: http://www.usersmanualguide.com/

E-16
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Video CD Playback
- Playback of a video CD (CDs) without P. B. C. (Version 1.1) -
Playback of a video CD (CDs) without P. B. C. (Version 1.1)
To interrupt playback:
Press the button on the remote control.
To resume playback from the same point, press the /SELECT/RESUME button.
To stop playback:
Press the ( /RETURN) button.
To remove the video CDs:
Whilst in the stop mode, press the OPEN/CLOSE button.
The disc tray will open. Remove the two discs. Then, press the DISC SKIP button to
rotate the disc tray and remove the remaining disc.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
1Turn on the TV and set the input selector to "VCR".
2Press the ON/STAND-BY button to turn the power on.
3Press the CD/VIDEO CD (CD) button.
4Press the OPEN/CLOSE button to open the disc tray.
5Place the video CD(s) on the disc tray, label side up.
When loading a third disc, press the DISC SKIP button to turn the
disc tray, then place the video CD in the open position.
!Video CDs can be placed in any open position in the disc tray.
!Be sure to place 8 cm (3") Video CD(s) in the middle of the disc positions.
6Press the OPEN/CLOSE button to close the disc tray.
Total number of tracks on the
video CD whose number is flashing Total playing time of the video CD whose number is flashing
7To select the video CD you want to listen to first, press the DISC
SKIP button.
8Press the / ( /SELECT/RESUME) button to start playback.
!Playback will begin from track 1 on the disc you have selected to play. After
that disc finishes playing, the next disc will automatically start playback.
!When the last track on the third disc has finished playing, the unit will stop au-
tomatically.
!When there is no video CD in one of the disc 1 - 3 positions, the next video
CD will be played.
General control (See page 10.)
Downloaded from: http://www.usersmanualguide.com/

E-17
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Video CD Playback
- Playback of a video CD (CDs) without P. B. C. (Version 1.1) -
Playback of a video CD (CDs) without P. B. C. (Version 1.1) (continued)
"To skip to the beginning of a track (skip
search)
Notes:
!You can skip to the beginning of a track on a single disc only.
!The PREV. or NEXT button on the remote control allows you to locate the
beginning of a track.
"Scan play
Notes:
!Normal playback will resume when the / or / button is released.
!You can locate the desired portion on a single disc only.
!During scan play, colours may fade, pictures may be distorted, or noise bars may
be seen.
!Pictures are shown intermittently and no sound is heard during fast forward or fast
reverse on video CDs.
!This can be operated by pressing the or button on the remote control.
"Direct search system
By using the direct search buttons, the desired tracks can be played.
To stop playback:
Press the ( /RETURN) button.
Notes:
!The selected track can be started simply by pressing the direct search buttons
during playback. [It is not necessary to press the / ( /SELECT/RESUME)
button.]
!A track number higher than the number of tracks on the disc cannot be selected.
!During random play, direct search system is not possible.
To move to the beginning of the next track:
Press the / button for less than 0.5 seconds during playback.
!You can skip to any track by pressing the / button repeatedly until the de-
sired track number appears.
To restart the track being played:
Press the / button for less than 0.5 seconds during playback.
!You can skip to any track by pressing the / button repeatedly until the de-
sired track number appears.
[Example] When the current track is 9
Beginning of track 9 Beginning of track 10
For fast forward:
Press and hold down the / button during playback.
For fast reverse:
Press and hold down the / button during playback.
1Whilst in the stop mode, press the
DISC SKIP button to select the de-
sired disc.
Selected disc number
2Use the direct search buttons on the
remote control to select the desired
track.
Selected track number
!The direct search buttons allow you to select up to number 10.
!When selecting number 11 or more, use the "+10" button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "3" button.
B. For example, to choose 30
1 Press the "+10" button three times.
2 Press the "0" button.
3Press the / ( /SELECT/RESUME) button to start playback.
Playback of the selected track is started. When the end of last track of the disc
selected is reached, the next disc will be automatically started.
Downloaded from: http://www.usersmanualguide.com/

E-18
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Advanced Video CD (Version 1.1) Playback
- Programmed play -
Programmed play
You can choose up to 32 selections for playback in the order you like.
Adding tracks to the programme:
If a programme has been previously stored, the "MEMORY" indicator will be dis-
played. Then follow steps 1 - 3 to add tracks. The new tracks will be stored after the
last track of the original programme.
Notes:
!Opening the disc tray automatically cancels the programmed sequence.
!Even if you press the ON/STAND-BY button to enter the stand-by mode or the
function is changed from CD/VIDEO CD (CD) to another, the programmed selec-
tions will not be cleared.
!During programme operation, random play is not possible.
!The programme function will not work in the P.B.C. mode. Whilst the programme
function is active, the P.B.C. function will be cancelled automatically.
1Whilst in the stop mode, press the
DISC SKIP button to select the de-
sired disc.
Selected disc number
2Press the direct search buttons on
the remote control to select the de-
sired track.
Selected track number
You can also select a track by pressing the / ( PREV.) or /
(NEXT ) button.
3Press the MEMORY/SET (MEMORY)
button to save the track number.
Playback order
When the track is memorised, "MEMORY" will appear.
4Repeat steps 1 - 3 for other tracks. Up to 32 tracks can be pro-
grammed.
If you make a mistake, the programmed tracks can be cleared by pressing the
CLEAR button.
5Press the / ( /SELECT/RESUME) button to start playback.
To clear the programmed selections:
Press the CLEAR button on the remote control
whilst the "MEMORY" indicator is lit.
Each time the button is pressed, one track will
be cleared, beginning with the last track pro-
grammed. When all the tracks are cleared,
"MEMORY" will disappear.
Downloaded from: http://www.usersmanualguide.com/

E-19
CD-BP99V(X)E2.fm01/7/13
ENGLISH
CD-BP99V
Advanced Video CD (Version 1.1) Playback
- Repeat or random play / Time search selection -
Repeat or random play
"Repeat play
All tracks on up to 3 discs, or a programmed sequence can be continuously repeated.
To repeat a desired track:
Perform steps 1 - 4 in the "Programmed play" section and then press the / ( /
SELECT/RESUME) button twice.
To cancel repeat play:
Press the / ( /SELECT/RESUME) button again.
" " will go out.
"Random play
The tracks on the disc(s) can be played in random order automatically.
To cancel random play:
Press the /SELECT/RESUME button.
"R" will go out.
Notes:
!If you press the NEXT button during random play, you can move to the track
selected next by the random operation. On the other hand, the PREV. button
does not allow you to move to the previous track. The beginning of the track being
played will be located.
!In random play, the CD player will select and play tracks automatically. (You cannot
select the order of the tracks.)
!Repeat or random function will not work during P.B.C. play. Cancel the P.B.C. mode
before using this function on a video CD with P.B.C.
Caution:
After performing repeat or random play, be sure to press the ( /RETURN) button.
Otherwise, the disc(s) will play continuously.
Time search selection
You can play back from the desired scene by specifying the time.
To cancel the time search operation:
Press the ( /RETURN) button.
Notes:
!Time search mode will be cancelled automatically if the desired time is not entered
within 10 seconds.
!The time search function will not work during P.B.C. and programme play. Cancel
the P.B.C. mode before using this function on a video CD with P.B.C.
!This operation is not accepted by still pictures (menu display, photo, etc.).
To repeat all tracks on up to 3 discs:
Press the / ( /SELECT/RESUME) button twice.
Press the RANDOM button on the re-
mote control to begin random play.
"R" will appear.
1Whilst in the stop or playback mode, hold down the DIGEST (DI-
GEST/TIME SEARCH) button to enter the time search mode.
During playback, the current track number is displayed.
2Use the direct search buttons on the remote control to specify the
time and track number.
[For example, to select track No. 3, 2 minutes and 30 seconds.]
Press "0", "2", "3", "0" and "3" successively.
Selected track number Selected time
!If you enter an incorrect time in the time search mode or if you want to change
the entered time, press the CLEAR button on the remote control. Each time
the CLEAR button is pressed, the last digit will be erased.
!The track number can be changed only after setting the time.
3Press the DIGEST (DIGEST/TIME SEARCH) button again to start
playback from the selected time.
When the last track on the third disc has finished playing, the unit will stop auto-
matically.
TIME SEARCH
TNO 01 - - : - -
<TV screen>
DI SC NO.02
TNO 03 2:30
<TV screen>
Downloaded from: http://www.usersmanualguide.com/