Sharp Aquos LC-13S1U User manual

LC-13S1U
LC-15S1U
LC-20S1 U
LIQUID CRYSTALTELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please
record the TV's model and serial numbers in the
space provided. The numbers are located at the
rear of the TV.
Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
The lightning flash with arrow-
head symbol, within
an equilat-
eral triangle, is intended to alert
the user to the presence of
uninsulated "dangerous voltage"
within the product's enclosure
that may be of sufficient
magnitude to constitute arisk of
electric shock to persons.
CAUTION
ARISK OF ELECTRIC SHOCK A A
..... DO NOT OPEN ..........
L...- -----J
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO
NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a
Atriangle is intended to alert the
user to the presence of impor-
tant operating and maintenance
(servicing) instructions
in the
literature accompanying the
product.

IMPORTANT INFORMATION (Continued)
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user's authority to operate this equipment.
IU.S.A. ONLYI
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG
TO WIDE SLOT, FULLY INSERT.
"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40
of the National Electrical Code that provides guidelines for proper grounding and,
in particular, specifies that the cable
ground shall be connected to the grounding system of the building,
as close to the point of cable entry as practical."
This product utilizes tin-lead solder, and fluorescent lamp containing asmall amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries Alliance:
www.eia.org
2@

DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety
and many years of trouble-free operation of your product, please read the Important
Safety Precautions carefully before using this product.
IMPORTANT SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property
damage if improperly handled. This product has been engineered and manufactured with the highest
priority
on safety. However, improper use can result in electric shock and/or fire. In order to prevent
potential danger, please observe the following instructions when installing, operating and cleaning the
product. To ensure your safety and prolong the service life of your Liquid Crystal Television, please
read the following precautions carefully before using the product.
•Read
instructions-All operating instructions must be read and understood before the product is
operated.
•Keep this manual
in asafe place-These safety and operating instructions must be kept in a
safe place for future reference.
•Observe
warnings-All warnings on the product and in the instructions must be observed
closely.
•Follow
instructions-All operating instructions must be followed.
•
Attachments-Do not use attachments not recommended by the manufacturer. Use of inad-
equate attachments can result
in accidents.
•Power
source-This product must operate on apower source specified on the specification
label.
If you are not sure of the type of power supply used in your home, consult your dealer or
local power company. For units designed to operate
on batteries or another power source, refer
to the operating instructions.
•Power cord
protection-The power cords must be routed properly to prevent people from
stepping
on them or objects from resting on them. Check the cords at the plugs and product.
•
If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a
SHARP service center or your dealer.
•
Overloading-Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.
•Entering of objects and
liquids-Never insert an object into the product through vents or open-
ings. High voltage flows
in the product, and inserting an object can cause electric shock and/or
short internal parts. For the same reason, do not spill water or liquid on the product.
•
Servicing-Do not attempt to service the product yourself. Removing covers can expose you to
high voltage and other dangerous conditions. Request aqualified service person to perform
servicing.
•
Repair-If any of the following conditions occurs, unplug the power cord from the AC outlet, and
request aqualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When aliquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described
in the operating instructions. Improper
adjustment of controls not described
in the instructions can cause damage, which often
requires extensive adjustment work by aqualified technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product
indicates that the product needs servicing.
•Replacement
parts-In case the product needs replacement parts, make sure that the service
person uses replacement parts specified by the manufacturer, or those with the same character-
istics and performance as the original parts. Use of unauthorized parts can result
in fire, electric
shock and/or other danger.
•Safety
checks-Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product
is in proper operating condition.
•Wall or ceiling
mounting-When mounting the product on awall or ceiling, be sure to install the
product according to the method recommended by the manufacturer.
•
Polarization-This AC adapter may be equipped with apolarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This
is asafety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
@)3

IMPORTANT SAFETY PRECAUTIONS (Continued)
• Cleaning-Unplug the power cord from the AC outlet before
cleaning the
product Use adamp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
•Water and
moisture-Do not use the product near water,
such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and
in awet basement.
•
Stand-Do not place the product on an unstable cart, stand,
tripod or table. Placing the product
on an unstable base can
cause the product to fall, resulting
in serious personal
injuries
as well as damage to the product. Use only acart,
stand, tripod, bracket or table recommended by the manu-
facturer or sold with the product. When mounting the product
on awall,
be sure to follow the manufacturer's instructions.
Use only the mounting hardware recommended by the
manufacturer.
•When relocating the product placed
on acart, it must be
moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.
•
Ventilation-The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause over-
heating and/or shorten the life of the product. Do not place
the product
on abed, sofa, rug or other similar surface,
since they can block ventilation openings. This product
is not
designed for built-in installation; do not place the product
in
an enclosed place such as abookcase or rack, unless
proper ventilation
is provided or the manufacturer's instruc-
tions are followed.
•The Liquid Crystal panel used
in this product is made of
glass. Therefore, it can break when the product
is dropped
or applied with impact. Be careful not to be injured by broken
glass pieces
in case the Liquid Crystal panel breaks.
•Heat
sources-Keep the product away from heat sources
such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
------,~~
~~~~-;~
•The Liquid Crystal panel is avery high technology product with 921,600 thin film transistors, giving
you fine picture details.
Occasionally, afew non-active pixels may appear
on the screen as afixed point of blue, green or red.
Please note that this does not affect the performance of your product.
4@

IMPORTANT SAFETY PRECAUTIONS (Continued)
•Outdoor Antenna Grounding -If an outside antenna is connected to the television equipment, be
sure the antenna system
is grounded so as to provide some protection against voltage surges and
built-up static charges. Article
81 °of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting structure, grounding of the
lead-in wire
to an antenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD
IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
-='- POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H) NEC-NATIONAL ELECTRICAL CODE
GROUND
CLAMP
•Lightning -For added protection for this television equipment
during alightning storm, or when it
is left unattended and
unused for long period of time, unplug it from the wall outlet
and disconnect the antenna. This will prevent damage
to the
equipment due
to lightning and power-line surges.
•Power Lines -
An outside antenna system should not be
located
in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing
an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits
as contact with them might be
fatal.
•
To prevent fire, never place any type of candle or naked
flames
on the top or near the TV set.
•To prevent fire or shock hazard, do not expose this product
to dripping or splashing. No objects filled with liquids, such
as vases, should be placed on the product.
@s

CONTENTS
Page
IMPORTANT INFORMATION
1, 2
DEAR SHARP CUSTOMER ...........................................................................................................•.3
IMPORTANT SAFETY PRECAUTIONS 3-5
CONTENTS 6
SUPPLIED ACCESSORIES 7
PREPARATION
8-11
Using the Remote Control 8
Batteries for the Remote Control 8
Removing the Terminal Cover 9
Bundling Cables with Clamp 9
Antenna Connection 10,
11
Power Connection 11
DISPLAY AND CONTROL OVERVIEW 12, 13
REMOTE CONTROL 14
EZ SETUP (WITH AUTO CLOCK SETTING) 15, 16
EZ SETUP
during the First Power On 15, 16
SETTING THE CLOCK
., 17-19
AUTO CLOCK Setting 17, 18
MANUAL CLOCK Setting 19
BASIC OPERATION 20-24
TV
signals in your region 20
Turning on POWER 21
Standby 21
Switching TVNIDEO [AV1/AV2/COMPONENTITV] Modes 22
Sound Volume 23
Listening with Headphones 23
Changing Channels 24
SELECTING MENU ITEMS
25
Selecting Menu Items 25
ADJUSTMENTS 26-46
Adjusting SLEEP TIMER Settings 26
Adjusting BRIGHTNESS Settings 27
Adjusting PICTURE FLIP Settings 28
Adjusting AUDIO ONLY Settings 29
Adjusting PRESET Settings 30
Adjusting LANGUAGE Settings 31
Adjusting VIDEO ADJUST Settings 32, 33
Adjusting AUDIO ADJUST Settings 34
SET
UP 35~ 36
Adjusting BLUE SCREEN Settings 37
Adjusting CLOSED CAPTION Settings 38, 39
Adjusting V-CHIP Settings 40-46
CONNECTING EXTERNAL DEVICES 47-49
TROUBLESHOOTING 50,
51
SPECIFICATIONS 52
DIMENSIONAL DRAWINGS 53-55
CALLING FOR SERVICE 56
LIMITED WARRANTY
56~ 57
6@

SUPPLIED ACCESSORIES
Make sure the following accessories are provided with the product.
RRMCGA174WJSA
QCNWG0003CEPA QACCDA023WJPA
111': .. :: ....
SHARP.
I
~I
~I
UADP-A044WJPZ TINS-A857WJZZ LHLDWA002WJSB
INOTE >
•AC cord enclosed in this product is an object for 11 0-125V. In using it on the 125-240V AC, please consult to the
following.
SHARP ELECTRONICS CORPORATION
1300 Naperville Drive, Romeoville, Illinois 60446-1091, U.S.A. TEL: [phone]
@7

PREPARATION
o • 0©
1" i ~LHEADPHONE jack
OPC indicator
POWER indicator
L...-- Remote control
sensor
'--------OPC sensor
•Use the remote control by pointing it towards the remote
control sensor window
on the main unit. Objects between
the remote control and sensor window may prevent proper
operation.
Cautions regarding use of the remote control f
• Do not expose the remote control to shock. ,
In addition, do not expose the remote control to liquid, and
do not place
in an area with high humidity.
•
Do not install or place the remote control under direct
sunlight. The heat may cause deformation of the unit.
•The remote control may not work properly if the remote
control sensor window of the main unit
is under direct
sunlight or strong lighting.
In such case, change the angle of
the lighting or LCD TV set, or operate the remote control
closer to the remote control sensor window.
Before using the LCD
TV set for the first time, install two ("AAA" size) batteries (supplied). When the
batteries become depleted and the remote control fails to operate, replace the batteries with new
("AAA" size) batteries.
1Open the battery
cover. 2Insert two ("AAA" size)
batteries. 3Close the battery
cover.
•Slide the cover while
pressing the
(T) part. •Position the positive and
negative ends of the batteries
as indicated
in the compart-
ment.
•Engage the claw
on the
cover into the battery
housing and slide shut.
Cautions regarding batteries
Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the instruc-
tions below.
•Place batteries with their terminals corresponding to the (+) and
(-) as indicated in the compartment.
•Different types of batteries have different characteristics. Do not mix batteries of different types.
•Do not mix old and
new batteries. Mixing old and new batteries can shorten the life of new
battery and/or cause the old battery to leak chemicals.
•Remove batteries when they become weak.
Chemicals that leak from batteries can cause arash. If chemical leakage is found, wipe with a
cloth.
•
The batteries supplied with the product may have ashorter life expectancy due to storage conditions.
•If the remote control will not be used for an extended period of time, remove the batteries from the
remote control.
s@

PREPARATION (Continued)
LC-20S1U
•Before connecting cables and cords to the rear terminals, remove the
terminal cover. Push
in the tab and pull out the terminal cover carefully.
•To mount the cover, insert the 2hooks
on the bottom of the cover
into the cabinet and press
on the upper part of the terminal cover
until the tab locks
in place with aclick.
LC-13/15S1 U
•Before connecting cables and cords to the rear
terminals, remove the terminal cover. Push
in the 2
tabs
on the right side of the terminal cover and pull it
out carefully to the left.
•To mount the cover, insert the 2hooks
on the left side
of the cover into the cabinet and press
on the right part
of the cover until the tabs lock into place with aclick.
•Secure cables and cords with the supplied
cable clamp so that they do not get caught
when mounting the cover.
@g

PREPARATION (Continued)
• The antenna requirements for good color television reception are more important than those for black &white
television reception. For this reason, agood quality outdoor antenna is strongly recommended.
The following is abrief explanation of the type of connections that are provided with the various antenna
systems.
1. A 75-ohm system is generally around cable with F-type
connector that can easily be attached to aterminal without
tools (not supplied).
F-type connector
~
---.
75-ohm coaxial cable (round)
2. A300-ohm system is aflat "twin-lead" cable that can be
attached to a75-ohm terminal through a300-75-ohm
adapter (not supplied).
"::.: ::
300-ohm twin-lead cable (flat)
OUTDOOR ANTENNA CONNECTION
•Use one of the following two diagrams if you connect an outdoor antenna.
A: Using aVHF/UHF combination outdoor antenna
B: Using separate VHF and/or UHF outdoor antennas
•Connect the outdoor antenna cable lead-in to ANT. (Antenna terminal) on the rear of the TV set.
A. Combination VHF/UHF Antenna
""
Combiner
300-ohm (not supplied)
twin-lead I ~
.~~b= --+ IN OUT F
l .... coaxi~f~~~ /
300/75-ohm
VHF/UHF adapter J
1[
antenna lor~~ .. .... ~~:~~~F
300-ohm
twin-lead
75-ohm
coaxial cable
B. Separate VHFand/or
UHF Antennas
UHF
VHF antenna
antenna
~ F-type connector
~i~
~~~ ~
75-ohm coaxial cable
F-type connector should befinger-tightened only.
When connecting the RF cable to the TV set,
do not tighten F-type connector with tools.
If tools are used, it may cause damageto your
TV set.
(The breaking of internal circuit, etc.)

PREPARATION (Continued)
CABLE TV (CATV) CONNECTION
• A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75-
ohm coaxial cable to the set, screw the 75-ohm cable to the ANT. terminal.
•Some cable
TV companies offer "premium pay channels". Since the signals of these premium pay
channels are scrambled, acable
TV converter/descrambler is generally provided to the subscriber
by the cable
TV company. This converter/descrambler is necessary for normal viewing of the
scrambled channels. (Set
your TV to channel 3 or 4, typically one of these channels is used. If this
is unknown, consult your cable
TV company.) For more specific instructions on installing cable TV,
consult
your cable TV company. One possible method of utilizing the converter/descrambler
provided by your cable
TV company is explained below.
Please note: An RF switch provided with two inputs (A and B) is required (not supplied).
"A" position on the RF switch (not supplied):
You can view all unscrambled channels by using the TV's
channel keys.
"8" position on the RF switch (not supplied):
You can view the scrambled channels via the converter/
descrambler by using the converter's channel keys.
RF switch (not supplied) Two-set
AEi. ·illI:· ::.------_111]:: signal
.. -_[>.i~:m ':: OUT~ IN splitter
B·:. (not
'------' supplied)
Cable TV converter/
descrambler
(not supplied)
Cable TV Line
INOTE >
•Consult your SHARP Dealer or Service Center for the type of splitter, RF switch or combiner that might be
required.
Household power outlet
[[ill,
AC ~ AC adapter
L~'J$
MAIN POWER
CNOTE>
•Use acommercially available AC plug adapter, if necessary, depending on the design of the wall outlet.
•Always turn the MAIN POWER switch of the LCD TV set to off when connecting the
AC adapter.
•Unplug the
AC adapter from the product and power outlet when not using for along period of time.

DISPLAY AND CONTROL OVERVIEW
Upper control panel
~AdjUstable
~ range
The screen can be
adjusted backwards to an
angle between 12
degrees and 35 degrees.
The screen cannot be set
up straight. When
changing the angle, make
sure to hold the stand and
adjust the screen to the
best viewable angle.
HEADPHONE jack
Plug the headphone mini-plug into the HEADPHONE
jack located on the front of the TV set.
OPC indicator (Optical Picture Control)
The Optical Picture Control indicator lights up green
when the BRIGHTNESS is set to AUTO. (See page 27.)
~------- VOL (-)/(+)
,...-------- CH (V)/(A)
,...........----MENU
r----- TVNIDEO
MAIN POWER
OPC
sensor
Remote control sensor ----I
t...-..- POWER indicator
Agreen indicator lights when the power is on and a red
indicator lights when in the standby mode (the indicator
will not light when the main power
is off).
*The examples used throughout this manual are based
on the LC-20S1U model.
[N()Tr>
•TVNIDEO, CH (V)/(A), VOL (-)/(+), and MENU on the main unit have the same functions as the same buttons
on the remote control. Basically, this operation manual provides adescription based on operation with the remote
control.
12@

DISPLAY AND CONTROL OVERVIEW (Continued)
Terminals
VIDEO }
AUDIO (L)
AUDIO (R) AV-IN1
S-VIDEO
ANT. (Antenna terminal)
~ }COMPONENT
AUDIO (L)
~".....u..u,----- AUDIO (R)
POWER INPUT
(DC12V)
Round lock for Kensington
Security Standard Slot.
I
Stand
•The screen can
be
adjusted backwards to
an angle between 12
and 35 degrees.
When changing the
angle, make sure to hold
the stand and adjust to
the best viewable angle.
* Be careful to prevent the
product from falling over
when adjusting the angle.
Also place the product
on
astable base.
AV-
1N2/
OUT
R ~
AUD:IO
L ~
VIDEO~
S-VIDEO~
(INPUT ONLY)
Carrying handle
:~~:~ ~:; } AV-OUJAV-IN2
,Jt--+----+- VIDEO
.MH-+----I- S-VIDEO
(INPUT ONLY)

REMOTE CONTROL
1
2-~~
3------=
4--~
5--~
6--~~·:·::~-""··"""",,--,,;,:
7---~
8---a~~.
9------;;~
1POWER (p. 21)
Switch the Liquid Crystal Television power
10
on or off.
11
2SLEEP (p. 26)
Set the sleep timer.
12 3ENTER
Execute acommand.
13 4DISPLAY
14 Display the channel and time information.
15 5AUDIO ONLY (p. 29)
16 Output audio without screen image.
6MUTE (p. 23)
Mute the sound.
17 7VOL (+)/(-) (p. 23)
Set the volume.
8CH
(A)/(V) (p. 24)
Select channel.
9MTS (p. 23)
Select audio settings.
10 BRIGHT (p. 27)
Adjust the brightness of the screen.
11 PIC. FLIP (p. 28)
Set the orientation of the picture.
12 ~/T / .....-/~ (Cursor control) (p. 15)
Select adesired item on the screen.
13 MENU (p. 17)
Display the menu screen.
14 CC (p. 38)
Display Closed Caption subtitles.
15 TVNIDEO (p. 22)
Select aLiquid Crystal Television input
source.
16 FLASHBACK (p. 24)
Return to the previous channel.
17 Channel Select (p. 24)
Set the channel.

EZ SETUP (WITH AUTO CLOCK SETTING)
•When you turn on the TV for the first time, it will automatically
memorize the broadcasting channels and clock.
Please perform the following instructions before you press MAIN
POWER.
(1) Insert the batteries into the remote control. (See page 8.)
(2) Connect the antenna cable to the
TV set. (See page 10.)
(3) Connect the AC adapter to the
POWER INPUT terminal of the
product and plug in the AC cord to the wall outlet. (See page 11.)
Control section of main unit
MAIN POWER
1Press MAIN POWER, located on
the upper side of the main unit, to
turn on the TV. The
SELECT
LANGUAGE mode will be dis-
played.
2Press ./T to select "ENGLISH",
"ESPANOL (SPANISH)"
or
"FRANCAIS (FRENCH)", and press
ENTER.
3Press ./T to select ON or OFF.
When you select ON, the
TV set
will automatically memorize the
broadcasting channels.
Press ENTER to access AUTO
CLOCK mode.
4Press ./T to select ON or OFF.
When you select ON, the
TV set
will automatically search the time
signals (EDS signals), provided by
some
TV stations, to adjust the
clock. The AUTO
CLOCK setting
may take from several minutes to
an hour depending on the number
of channels to receive and signal
status. If you know the channel of
the EDS signal carrier (PBS or
other)
in your area, select OFF and
follow the procedure in AUTO
CLOCK Setting. (See pages 17,
18)
5Press ENTER to access EZ
SETUP mode.
SELECT LANGUAGE
!U ENGLI SH
ESPANOL
FRANCA IS
SELECT:O ENTER:. EXIT:.
EZ SETUP
CH·SETTING
!U ON
OFF
SELECT:O ENTER:. EXIT:.
EZ SETUP
AUTO CLOCK
!U ON
OFF
SELECT:O ENTER:. EXIT:.
INOTE >
•If you select OFF in "EZ SETUP CH-SETTING", EZ SETUP will be canceled.

EZ SETUP (WITH AUTO CLOCK SETTING) (Continued)
CONNECT ANTENNA OR CABLE.
START EZ SETUP?
nJ YES
NO
6Press ./T to select YES, and
press ENTER.
If you want to stop the EZ SETUP
process once it has started, press
...... and it will be canceled. If you
want to SET UP again, please refer
to pages 35 and 36
on SET UP.
To cancel EZ SETUP
Press
./T to select NO, and
press ENTER.
The tuner will automatically search
for the broadcasting and cable TV
channels. (The
CH No. will auto-
matically increase when it ap-
pears.)
The TV set will automatically
search for EDS signals.
If EDS signals are received, the
channel number and time will
be
displayed, and then the screen
shown
in step 7appears.
7Once EZ SETUP is completed, the
lowest channel number memorized
will
be displayed.
SELECT:~ ENTER:.
PLEASE WAIT
AUTO PROGRAMMI NG
STOP:@
PLEASE WAIT
NOW SEARCH I NG TIME
STOP:@
OSTEREO <ON AIR
SAP
MONO
EXIT: •
2
11 : 53AM
INOTE >
• Do not let the EZ SETUP screen remain unattended for along time.
•If EZ SETUP does not memorize all the channels
in your region, please refer to pages 35 and 36 for more
information
on manually memorizing the channels using CHANNEL SETTING.
•It may be difficult to preset when the broadcasting signals are weak, the channel cycle frequency is incorrect or
the frequency jamming is occurring around the area. Please refer to pages 35 and 36 for more information
on
manually memorizing channels using CHANNEL SETTING.
•If there are
no channels with EDS signals or the antenna signal is weak, the AUTO CLOCK Setting may not
operate.
In this case, a"EDS CH IS NOT AVAILABLE" message will display and the mode will change to MANUAL
CLOCK Setting. Refer to page
19 to set the clock manually.

SETTING THE CLOCK
There are two methods of setting the clock: AUTO CLOCK and MANUAL CLOCK. AUTO CLOCK uses
EDS signals, which are provided by some TV stations, to automatically adjust the clock. MANUAL CLOCK
set the clock manually
in areas where no channel carries EDS signals.
1Press MENU to display the MENU
screen.
2Press .. IT to move the cursor to
SET
UP, and press ENTER.
3Press .. IT to move the cursor to
CLOCK, and press ENTER.
4Press .. IT to move the cursor to
AUTO CLOCK, and press ENTER.
MENU
~SLEEP TIMER
IIAV ADJUST
[gPRESET
gCLOSED CAPT I ON~
ImV-CH IP BLOCK
[Q'~SET UP
SELECT:O ENTER:. EXIT:.
SET UP
8RETURN
BLUE SCREEN [OFF]
LANGUAGE ~
CH-SETT I NG~
[Q' CLOCK ~
SELECT:G ENTER:. EXIT:.
CLOCK
8RETURN
[Q' AUTO CLOCK ~
MANUAL CLOCK~
OFF
SELECT:~ ENTER:. EXIT:.
INOTE >
•The CLOCK can be stopped completely by setting CLOCK to "OFF".
Time reset for power outage, AC adapter disconnected
If the TV has apower outage or the AC adapter cord is disconnected, the time display will have to
be reset.
In that case, refer to SETTING THE CLOCK on pages 17 to 19.

SETTING THE CLOCK (Continued)
5Press .. IT to move the cursor to
EDS
CH SET, and press ENTER.
6Press
...... /~ to select AUTO or
AUTO CLOCK
eRETURN
MANUAL.
rrr
EDS CH SET [AUTO
EDS CH
[---]
START
7Press
~JT to move the cursor to
START, and press ENTER.
ADJUST:@ ENTER:.
EXIT: •
PLEASE WAIT
NOW SEARCHING TIME
•If you do not know the channel that
carries EDS signals
in your area,
select EDS
CH SET to AUTO and
select START. If you know the
STOP:@
channel of the EDS signal carrier in
your area, select EDS CH SET to
MANUAL. Set the EDS
CH and 2
select START.
•When set to "AUTO CLOCK", the
time is acquired automatically when
MAIN POWER is turned OFF. (This
function will not work when EDS
CH is not set.)
rrrSTEREO <ON AIR
SAP
MONO
11:53AM
INOTE >
•CLOCK: The AUTO CLOCK Setting may take from several minutes to an hour depending on the number of
channels to receive and signal status.
•If there are no channels with EDS signals or the antenna signal
is weak, the AUTO CLOCK Setting may not
operate.
In this case, an "EDS CH IS NOT AVAILABLE" message will display, and the MANUAL CLOCK Setting
screen appears. Refer to MANUAL CLOCK Setting on page 19 to set the clock manually.
•If you know the Channel of the EDS signal carrier
in your area, set EDS CH SET to MANUAL and select START.
In case, the message "EDS CH (XXX) EDS DATA IS NOT AVAILABLE" displays, set EDS CH SET to AUTO when
the AUTO CLOCK Setting screen appears.
•If broadcasting channels are not memorized, EDS signals cannot
be received even when the EDS CH SET is set
to AUTO.
In this case, try EZ SETUP again. (See page 35.)
1S@

SETTING THE CLOCK (Continued)
If there are no channels with EDS signals, set the clock manually using MANUAL CLOCK.
1Press MENU to display the MENU
screen.
2Press l../T to move the cursor to
SET
UP, and press ENTER.
3Press l../T to move the cursor to
CLOCK, and press ENTER.
4Press l../T to move the cursor to
MANUAL CLOCK, and press
ENTER.
MENU
~SLEEP TIMER
IIAV ADJUST
lfIPRESET
~CLOSED CAPT I ON~
rmV-CH IP BLOCK
[O'~SET UP
SET UP
8RETURN
BLUE SCREEN [OFF]
LANGUAGE ~
CH-SETT I NG~
[0' CLOCK ~
CLOCK
E>RETURN
AUTO CLOCK ~
[0' MANUAL CLOCK~
OFF
SELECT:~ ENTER:. EX IT: •
5Press l../T to move the cursor to
TIME, and press ENTER.
6Press ~/~ to set the time, and
press ENTER.
C
12:00AM ~-----~11:59AM J
11:59PM ~-----~12:00PM
~
•Make sure to press ENTER after
adjusting the time. Otherwise, the time
will not be set.
•When DST is set to ON, the time
entered is forwarded by 1hour.
7Press MENU to return to the main
screen.
MANUAL CLOCK
8RETURN
[0' TIME [12: OOAM]
DST [OFF]
ADJUST:@ ENTER:.
EXIT: •
Daylight Saving-Time (DST) Adjustment
The Daylight Saving-Time changes as shown below, set the DST to ON to forward the clock by 1
hour.
To rewind the clock by 1hour, set the DST to OFF.
(Spring) (Autumn)
On the first Sunday in April D.S.T. starts. On the last Sunday in October D.S.T. finishes.
3:00AM 4:00AM
1
:OOAM 2:00AM
••
I
: ~ Rewinds 1hour.
I
••
1 :OOAM 2:00AM
: / Advances 1hour,
,.
1 :OOAM 2:00AM
.,