Sharp Aquos LC-40C37U User manual

SERVICE MANUAL
LC-40C37U
No. S46S3LC40C37U
LC-40C37U
MODEL
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
LIST OF CHANGED PARTS
LC-40C37U .........................................................i
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRE-
CAUTION ...........................................................ii
PRECAUTIONS A PRENDRE LORS DE
LA REPARATION .............................................. iii
PRECAUTIONS FOR USING LEAD-FREE
SOLDER ...........................................................iv
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS ......................................... 1-1
CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUAL .................................. 2-1
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS ................................................ 3-1
Parts Guide
TopPage
LCD COLOR TELEVISION
In the interests of user-safety (Required by safety regulations in some countries) the set should
be restored to its original condition and only parts identical to those specified should be used.
OUTLINE
This model is based on the LC-37D40U and is changed some parts. This Service Manual covers the modifications
alone. For the other points, refer to the LC-37/45D40U Service Manual.

LC-40C37U
i
LC-40C37U Service Manual
LIST OF CHANGED PARTS
LC-40C37U
Ref. No. Description LC-37D40U LC-40C37U Note
PWB ASSEMBLIES
MAIN Unit DUNTKD640FM06 DUNTKD640FM12 No parts changed
LED Unit DUNTKD641FM06 DUNTKD641FM12 No parts changed
IF Unit DUNTKD643FM06 DUNTKD643FM12 Some parts changed
KEY Unit DUNTKD716FM06 DUNTKD716FM12 No parts changed
POWER SUPPLY Unit RDENCA161WJQZ ←—
LCD PANEL
37" WIDE LCD Panel Module Unit R1LK370T3LZ5BY R1LK370T3LZ5BW —
IF Unit
FB2707 Balun, BLN-A192WJ — RBLN-A192WJZZY *Add
FB2708 Balun, BLN-A192WJ — RBLN-A192WJZZY *Add
CABINET AND MECHANICAL PARTS
Please refer to a Parts list.
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list.

LC-40C37U
ii
LC-40C37U Service Manual
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
• Plug the AC cord directly into a 120 volt AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have
special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts
List and Schematic Diagrams.
For continued protection, replacement parts must be identical to those
used in the original circuit.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
AV
CAUTION: FOR CONTINUED
PROTECTION AGAINST A RISK OF
FIRE REPLACE ONLY WITH SAME
TYPE FUSE.
F701 (8A, 125V),
F4701, F5701 (3A~, 250V, 115
O
C)
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
0.15 µ F
TEST PROBE

LC-40C37U
iii
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
De nombreuses pièces, électriques et mécaniques, dans les télévi-
seur ACL présentent des caractéristiques spéciales relatives à la sé-
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec-
tion ne peut pas être nécessairement augmentée en utilisant des
pièces de remplacement étalonnées pour haute tension, puissance,
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
Pour assurer la protection, ces pièces doivent être identiques à celles
utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
les mêmes caractéristiques que les pièces recommandées par l'usine,
indiquées dans ce manuel, peut provoquer des électrocutions, incen-
dies, radiations X ou autres accidents.
AVERTISSEMENT
1.
2.
3.
4.
5.
•
•
•
•
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
N'entreprendre aucune modification de tout circuit. C'est danger-
eux.
Débrancher le récepteur avant toute réparation.
Inspecter tous les faisceaux de câbles pour s'assurer que les fils
ne soient pas pincés ou qu'un outil ne soit pas placé entre le châs-
sis et les autres pièces métalliques du récepteur.
Inspecter tous les dispositifs de protection comme les boutons de
commande non-métalliques, les isolants, le dos du coffret, les cou-
vercles ou blindages de réglage et de compartiment, les réseaux
de résistancecapacité, les isolateurs mécaniques, etc.
S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la
fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent à une prise de cou-
rant de 120V. (Ne pas utiliser de transformateur d'isolation pour
cet essai).
A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ
10 watts en parallèle avec un condensateur de 0.15µF en série
avec toutes les pièces métalliques exposées du coffret et une terre
connue comme une conduite électrique ou une prise de terre
branchée à la terre.
Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour
mesurer la chute de tension en travers de la résistance.
Toucher avec la sonde d'essai les pièces métalliques exposées qui
présentent une voie de retour au châssis (antenne, coffret métalli-
que, tête des vis, arbres de commande et des boutons, écusson,
etc.) et mesurer la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir inversé la
fiche du cordon d'alimentation. (Si nécessaire, une prise
d'adpatation non polarisée peut être utilisée dans le but de termin-
er ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser 0.75V (corre-
spondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilité de choc électrique qui
doit être supprimée avant de rendre le récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer les vérifica-
tions suivantes.
DVM
ECHELLE CA
1.5k ohm
10W
0.15
µ F
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
AVIS POUR LA SECURITE
AV
PRECAUTION: POUR LA
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
FUSIBLE
F701 (8A, 125V),
F4701, F5701 (3A~, 250V, 115OC)

LC-40C37U
iv
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder
• "PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Using lead-free wire solder
• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Part No, Description Code
ZHNDAi123250E J φ0.3mm 250g(1roll) BL
ZHNDAi126500E J φ0.6mm 500g(1roll) BK
ZHNDAi12801KE J φ1.0mm 1kg(1roll) BM

LC-40C37U
1 – 1
LC-40C37U Service Manual
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS
Emergency alert messages via Cable are unreceivable.
•
•
As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
LCD panel
Number of dots
TV
Function
TV-standard (CCIR)
Receiving
Channel
VHF/UHF
CATV
Digital Terrestrial
Broadcast (8VSB)
Audio multiplex
Audio out
Terminals Rear INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5
ANTENNA
DIGITAL AUDIO OUTPUT
OUTPUT
OSD language
Power Requirement
Power Consumption
Weight
Dimension
(W H D)
Accessories
Operating temperature
3,147,264 dots (1366 768 3 dots)
American TV Standard ATSC/NTSC System
VHF 2-13ch, UHF 14-69ch
1-135ch* (non-scrambled channel only)
2-69ch
BTSC System
10W 2
AV in, COMPONENT in
AV in, COMPONENT in
S-VIDEO in, AV in
Audio in, HDMI in with HDCP
HDMI in with HDCP
75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
Optical Digital audio output 1 (PCM/Dolby Digital)
Audio out
English/French/Spanish
AC 120 V, 60 Hz
Remote control unit ( 1), AC cord ( 1), “AAA” size battery ( 2), Cable clamp ( 1),
Cable tie ( 1), Stand unit ( 1), Operation manual ( 1)
32°F to 104°F (0°C to 40°C)
Item Model: LC-40C37U
37" Advanced Super View & BLACK TFT LCD
with stand
w/o stand
w/o stand
with stand
186 W
48.5 lbs./22.0 kg
53.8 lbs./24.4 kg
37
1
/
4
26
15
/
64
4
5
/
8
inch
37
1
/
4
28
35
/
64
12
1
/
64
inch
x
x
x
x
x
xx
xx
xx
xx
xxxx
x
++ +

LC-40C37U
2 – 1
LC-40C37U Service Manual
CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUAL
Part names
TV (Front) TV (Rear)
Part names
POWER button
Channel buttons (CH /)
Volume buttons ( VOL /)
INPUT button
OPC indicator*
POWER
indicator**
OPC sensor*
Remote control sensor
+
-
INPUT 4
terminals
INPUT 3
terminals
AUDIO OUTPUT
terminals
INPUT 5 terminal DIGITAL AUDIO OUTPUT terminal Antenna/Cable in INPUT 1 terminals INPUT 2 terminals
AC INPUT terminal

LC-40C37U
2 – 2
Part names
Remote control unit Removing the stand
Setting the TV on the wall
Appendix
3 2
114
5 6 4 8
17 15
16 18 19
7
20
10
9
21
11 23
24 25
12 13 27
22 26
1 TV POWER: Switch the TV power on or enters standby
mode.
2 DISPLAY: Display the channel information. 3 SOURCE POWER: Turns the power of the external
equipment on and off.
4 External equipment operational buttons: Operate the
external equipment.
5 0–9:Set the channel. 6 • (DOT): 7 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2,
INPUT3, INPUT4, INPUT5)
8VOL/:Set the volume. 9 SURROUND: Select Surround settings. 10 FREEZE: Set the still image. Press again to return to
normal screen.
11 EXIT: Turn off the menu screen. 12 SLEEP: Set the sleep timer. 13 AUDIO: Selects the MTS/SAP or the audio mode during
multi-channelaudio broadcasts.
14 FUNCTION: Switches the remote control for TV,CBL/
SAT, VCR, DVD and AUDIO operation. Indicator lights up for the current mode. * To enter the code registration mode, you need to press FUNCTION and DISPLAY at the same time.
15 LIGHT : When pressed all buttons on the remote
control unit will light. The lighting will turn off if no operations are performed within about 5 seconds. This button is used for performing operations in low-light situations.
16 VIEW MODE: Select the screen size. 17 ENT: Jumps to a channel after selecting with the 0–9
buttons.
18 FLASHBACK:Return to the previous channel or input
external mode.
19 CH / : Select the channel. 20 MUTE: Mute the sound. 21 MENU: Display the menu screen. 22 ////ENTER: Select a desired item on the
screen.
23 RETURN: Return to the previous menu screen. 24 FAVORITE CH
A, B, C, D: Select four preset favorite channels in four different categories. While watching, you can toggle the selected channels by pressing A, B, C and D
25 FAVORITE: Register favorite channel. 26 CC: Display captions from a closed-caption source. 27 AV MODE: Select an audio or video setting. (STANDARD,
MOVIE,GAME, USER, DYNAMIC(Fixed), DYNAMIC.)
+
-
Before detaching (or attaching) stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it. Before attaching/detaching stand • Before performing work make sure to turn off the TV. • Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
CAUTION
• Installing the TV requires special skill that should only be performed by quali-ed service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that results in accident or injury.
Using an optional bracket to mount the TV • You can ask a quali-ed service professional about using an optional AN-37AG2 bracket to mount the TV to the
wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hangingonthewall AN-37AG2 wall mount bracket. (See the bracket instructions for details.)
Vertical mounting
About setting the TV angle
Unfasten the four screws used to secure the stand in place.
Detach the stand from the TV. (Hold the stand so it will not drop from the edge of the base area.)
NOTE
• To attach the stand, perform the above steps in reverse order.
Angular mounting
12
0° or 5°LC-40C37U
AngleofTV
hex key
NOTE
• Detach the cable clamp on the rear of the TV when using the optional mount bracket.

LC-40C37U
2 – 3
Basic adjustment settings
Menu items
Picture
Setup Audio
Option
Power Control
Digital Setup
List of menu items to help you with operations
OPC Backlight Contrast Brightness Color Tint Sharpness Advanced
Color Temp. Black 3D-Y/C Monochrome Film Mode Range of OPC
EZ Setup CH Setup Antenna Setup-DIGITAL Input Skip Input Label Parental CTRL Position Picture Flip Standby Mode Language Reset Treble Bass Balance Surround
Audio Only Digital Noise Reduction Input Select HDMI Setup Output Select Quick Shoot Color System Caption Setup Program Title Display Favorite CH
No Signal Off No Operation Off
Audio Setup

LC-40C37U
3 – 1
LC-40C37U Service Manual
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS
243/32 (612)
121/64 (305)
445/64 (119)
371/4(946)
3225/64 (822.6)
2835/64 (725)
2615/64 (666)
173/32 (434)
221/64 (59)
45/8(117)
77/8(200)
325/32 (96)
77/8(200)
1817/64 (463.8)
Unit: inch/(mm)

PARTS GUIDE
CONTENTS
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
LC-40C37U
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
★MARK: SPARE PARTS-DELIVERY SECTION
No. S46S3LC40C37U
LC-40C37U
MODEL
PartsGuide
[1] PRINTED WIRING BOARD
ASSEMBLIES (NOT
REPLACEMENT ITEM)
[2] LCD PANEL (NOTE: THE PARTS
HERE SHOWN ARE SUPPLIED AS
AN ASSEMBLY BUT NOT
INDEPENDENTLY.)
[3] DUNTKD643FM12 (IF Unit)
[4] CABINET AND MECHANICAL
PARTS
[5] SUPPLIED ACCESSORIES
[6] PACKING PARTS (NOT
REPLACEMENT ITEM)
[7] SERVICE JIGS

LC-40C37U
2
NO. PARTS CODE PRICE
RANK
NEW
MARK ★DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM)
NDUNTKD640FM12 - R MAIN Unit
NDUNTKD641FM12 - X LED Unit
NDUNTKD643FM12 - X IF Unit
NDUNTKD716FM12 - X KEY Unit
NRDENCA161WJQZ BQ X POWER SUPPLY Unit
[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPEN-
DENTLY.)
NR1LK370T3LZ5BW EX X 37" WIDE LCD Panel Module Unit
[3] DUNTKD643FM12 (IF Unit)
FB2707 RBLN-A192WJZZY AA X Balun, BLN-A192WJ
FB2708 RBLN-A192WJZZY AA X Balun, BLN-A192WJ

LC-40C37U
3
[4] CABINET AND MECHANICAL PARTS
3-1
10
59 64
1-1
4-1
4-2
4-3
5-1
5-2
1
50
51
30 55
55
11
4
5
38 43
63
62
36
18
15 61
44
56
54
35
58
26
32
29
29
21
1-3 1-2
1-6
1-6 1-6
1-6
6
53
23
53
16
12
24
21
27
55 20
55 57
57
55
2-1
2-4
2-2
2
27
65
49
21
32 55
30
13 8
59
45
3-2
3-4
3-3
31
27
57
3
47
46
48
34
1-4
1-4
1-5
1-5
2-3
5-3
5-4 5-3 5-4
5-4
5-3
17
52
41
55
14
22
19
55
58
55
25
37
7
43
42
55
66
33
42
9
39
55
37
1-7
5-3
5-5
40
5-5
5-6

LC-40C37U
4
NO. PARTS CODE PRICE
RANK
NEW
MARK ★DESCRIPTION
[4] CABINET AND MECHANICAL PARTS
1CCABAB259WJ02 BK X Front Cabinet Ass'y
1-1 Not Available - - Front Cabinet
1-2 Not Available - - Front Cover
1-3 HBDGBA065WJSA AD X Badge, SHARP
1-4 PSPAHA416WJZZ AC X Mask Spacer, x2
1-5 Not Available - - Mask Spacer, x2
1-6 Not Available - - Spacer, x6
1-7 Not Available - - POP Label
2CCABBA726WJ01 BQ X Rear Cabinet Ass'y
2-1 Not Available - - Rear Cabinet
2-2 LHLDWA055WJKZ AC X Wire Holder (for AC-code)
2-3 LHLDWA131WJKZ AF X Wire Holder
2-4 Not Available - - Spacer
3CCOVAB497WJ01 BD X Top Cover Ass'y
3-1 Not Available - - Top Cover
3-2 JBTN-A429WJKA AD X Power Button
3-3 JBTN-A535WJKA X Operation Button
3-4 MSPRCA049WJFW AD X Power Button Spring
4CDAi-A247WJ01 BC X Stand Support Ass'y
4-1 Not Available - - Support Cover
4-2 Not Available - - Stand Support
4-3 Not Available - - Screw Guide, x4
5CDAi-A246WJ03 BA X Stand Base Ass'y
5-1 Not Available - - Stand Base Cover
5-2 Not Available - - Base Angle
5-3 Not Available - - LEG Cushion-A, x4
5-4 Not Available - - LEG Cushion-B, x4
5-5 XEBS740P10000 AB X Screw, x10
5-6 Not Available - - Stand Label
6R1LK370T3LZ5BW EX X 37" WIDE LCD Panel Module Unit
7DUNTKD640FM12 - R MAIN Unit
8DUNTKD641FM12 - X LED Unit
9DUNTKD643FM12 - X IF Unit
10 DUNTKD716FM12 - X KEY Unit
11 RDENCA161WJQZ BQ X POWER SUPPLY Unit
12 GCOVAA678WJKA AG X SD Card Cover
13 GCOVAB501WJSA AF X LED Cover
14 GCOVAB507WJKA AU X Stand Cover
15 HiNDPB603WJSA AK X Jack Indicator
16 HiNDPB715WJSA AF X Terminal Label
17 HiNDPB701WJSA AH X MODEL Label
18 LANGKA644WJFW AL X Jack Angle Long
19 LANGKA649WJFW AR X Stand Fix Angle
20 LANGKA655WJFW AH X Center Asist Angle
21 LANGKA663WJFW AK X Rug Angle, x4
22 LANGTA266WJFW AR X Stand Asist Angle
23 LANGTA291WJFW AR X Center Angle-R
24 LANGTA292WJFW AR X Center Angle-L
25 LBSHZA005WJZZ AB X Clip, x2
26 LCHSMA286WJFW AX X Chassis
27 LHLDW1173CEZZ AE X Wire Holder, x3
29 LHLDWA043WJKZ AC X Wire Holder (for Shield), x2
30 LHLDWA043WJKZ AC X Wire Holder (for Chassis), x2
31 LHLDWA048WJKZ AB X Wire Holder (for POWER Unit)
32 LHLDWA092WJZZ AB X Wire Holder (for Chassis), x2
33 LHLDWA096WJKZ AD X Wire Holder (for IF Unit)
34 Not Available - - Screw (for Stand Ass'y), x4
35 Not Available - - Screw (for Stand), x4
36 LX-NZ3047GEZZ AB X Hexiagonal Nut
37 PRDARA192WJFW AE X Hest Sink (for AV Switch)
38 PRDARA204WJFW AE X Hest Sink (for AMP-Bottom)
39 PRDARA312WJFW AE X Hest Sink (for AMP-Top)
40 PRDARA330WJFW AM X Hest Sink (for MAIN Unit)
41 PSLDMA910WJFW AV X MAIN Shield
42 PSPAZA635WJKZ AC X Spacer (Cool Sheet), x3
43 PSPAZA700WJKZ AD X Spacer (Cool Sheet), x3
44 QCNCWA496WJZZ AK X Connector (F-RCA)
45 QCNW-E265WJQZ AK X Connecting Cord (RA)
46 QCNW-E267WJQZ AG X Connecting Cord (LB)
47 QCNW-E286WJQZ AH X Connecting Cord (SP)
48 QCNW-E439WJQZ AH X Connecting Cord (LA)
49 QCNW-E537WJPZ BA X Connecting Cord (LV)
50 RSP-ZA166WJZZ AU X Speaker L
51 RSP-ZA167WJZZ AU X Speaker R
52 Not Available - - No. Label
53 XBBS740P06000 AA X Screw (for Angle), x6
54 XBBS930P06000 AA X Screw (for Cab-B), x5
55 XBPS730P06WS0 AB X Screw (for Angle, PWB), x39
56 XBPS930P08000 AA X Screw (for HDMI), x2
57 XEBS940P10000 AB X Screw (for Panel), x4
58 XEBS940P16000 AA X Screw (for Cab-B), x12
59 XEBSN30P10000 AA X Screw (for PWB), x5
61 XEBS930P08000 AA X Screw (for Jack), x3
62 QCNW-E257WJQZ AH R Connecting Cord (PE)
63 QCNW-E258WJQZ AG R Connecting Cord (PD)

LC-40C37U
5
NO. PARTS CODE PRICE
RANK
NEW
MARK ★DESCRIPTION
[5] SUPPLIED ACCESSORIES
NO. PARTS CODE PRICE
RANK
NEW
MARK ★DESCRIPTION
64 QCNW-E266WJQZ AF R Connecting Cord (KM)
65 QCNW-E278WJQZ AH R Connecting Cord (SH)
66 QCNW-E442WJPZ AH R Connecting Cord (COAXIAL)
[5] SUPPLIED ACCESSORIES
X1 LHLDW0110CESD AF X Cable Clamp
X2 LHLDWA083WJ00 AD X Cable Band
!
X3 QACCDA039WJPZ AR X AC Cord
X4 RRMCGA416WJSA BA X Remote Control Unit
X5 CDAi-A246WJ25 BL X Stand Ass'y
X6 TCADEA126WJZZ AC X Enquete Card
X7 TiNS-C413WJZZ AQ X Operation Manual
X8 TCAUZA228WJZZ X Caution Card
X9 TCAUHA184WJZZ AD X Set up Guide
X10 Not Available - - "AAA" Size Battery
[4] CABINET AND MECHANICAL PARTS
Operation manual Stand Ass'y
Remote Control Unit
X4
Cable Clamp
X1
Cable Band
X2
AC Cord
X3
X7 X5
X9
X10
X6
X8

LC-40C37U
6
[6] PACKING PARTS (NOT REPLACEMENT ITEM)
NO. PARTS CODE PRICE
RANK
NEW
MARK ★DESCRIPTION
[6] PACKING PARTS (NOT REPLACEMENT ITEM)
S1 SPAKCC521WJZZ - - Packing Case
S2 SPAKFA916WJZZ - - Stand Case
S3 SPAKPA338WJZZ - - Wrapping Paper (Monitor)
S4 SPAKPA601WJZZ - - Wrapping Paper (Mirror Mat A)
S5 SPAKPA602WJZZ - - Wrapping Paper (Mirror Mat B)
S6 SPAKXA957WJZZ - - Packing Add.
S7 SPAKXB198WJZZ - - Stand Pad
S8 TLABKA009WJZZ - - No. Label
S1
S3
S2
S6 S8
S6
S6
S6
S4
S5
S7

LC-40C37U
7
NO. PARTS CODE PRICE
RANK
NEW
MARK ★DESCRIPTION
[7] SERVICE JIGS
NQCNW-C799WJPZ AG J RCA Cable L=1500mm, Tuner to Terminal
NQCNW-D483WJQZ AX J 12pins L=1000mm, Main to Power Unit (PE)
NQCNW-E068WJQZ AS J 6pins L=1000mm, Main to Power Unit (PD)
NQCNW-E670WJQZ AP J 4-8pins L=1000mm, Main to Inverter Unit (LB)
NQCNW-E671WJQZ AW J 10-14pins L=1000mm, Power to Inverter Unit (LA)
NQCNW-E673WJQZ BE J 32pins L=1000mm, Main to Controller Unit (LV)
NQCNW-E674WJQZ AS J 7pins L=1000mm, Main to Controller Unit (SH)

SHARP CORPORATION
AV Systems Group
CS Promotion Center
Yaita, Tochigi 329-2193, Japan
TQ2016-S
Apr. 2006 Printed in Japan
Design and Production Information
Design: Japan
Production: SEMEX
SY. KD
COPYRIGHT 2006 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
LC-40C37U