Sharp LC-32GD8EA/RUA User manual

DIFFERENCES FROM BASE MODEL
LIST OF CHANGED PARTS...............................i
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRE-
CAUTION ...........................................................ii
PRECAUTIONS FOR USING LEAD-FREE
SOLDER ........................................................... iii
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS ......................................... 1-1
CHAPTER 2. DIMENSIONS
[1] DIMENSIONS ................................................ 2-1
CHAPTER 3. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIA-
GRAM ............................................................ 3-1
[2] MAIN Unit....................................................... 3-2
Parts Guide
SERVICE MANUAL
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
TopPage
CONTENTS
LC-32GD8EA/RUA, LC-32BT8EA/RUA
LC-32GD8EA/RUA
LC-32BT8EA/RUA
No. SY6Z3LC32D8EA
MODELS
LCD COLOUR TELEVISION
In the interests of user-safety (Required by safety regulations in some countries) the set shouldA
be restored to its original condition and only parts identical to those specified should be used.
OUTLINE
This model is based on the LC-32GD8E, LC-32BT8E and is changed some parts. This Service Manual covers the
modifications alone. For the other points, refer to the LC-32/37GD8E/RU, LC-32/37BT8E/RU Service Manual.

LC-32GD8EA/RUA, LC-32BT8EA/RUA
i
LC-32GD8EA/RUA, LC-32BT8EA/RUA Service Manual
DIFFERENCES FROM BASE MODEL
LIST OF CHANGED PARTS
Ref. No. Description LC-32GD8E LC-32GD8EA/RUA, LC-32BT8EA/RUA Note
PWB ASSEMBLIES
AV Unit DUNTKD604FM10 ←–
POWER Unit DUNTKD605FM14 ←–
OPERATION Unit DUNTKD606FMV0 ←–
R/C, LED Unit DUNTKD607FMV0 ←–
DIGITAL TUNER Unit CKITKD609FM01 ←–
DIGITAL Unit DUNTKD628FM01 ←–
MAIN Unit DUNTKD890FM06 DUNTKD890FM28 Some parts changed
MAIN Unit
C1747 Capacitor – VCCCCY1HH101JY Add
C1748 Capacitor – VCCCCY1HH101JY Add
C1749 Capacitor – VCKYCY1HB221KY Add
C1750 Capacitor – VCCCCY1HH101JY Add
C1751 Capacitor – VCCCCY1HH101JY Add
C1752 Capacitor – VCCCCY1HH101JY Add
IC1905 IC VHISII9023+-1Q VHISII9021+-1Q or VHISII9023+-1Q or use
P1701 Plug – QPLGNA342WJZZY Add
P2305 Plug QPLGNA522WJQZY QPLGNA493WJZZY Change
R1715 Resistor – VRS-CY1JF470JY Add
R1717 Resistor VRS-CY1JF000JY VRS-CY1JF470JY Change
R1718 Resistor – VRS-CY1JF470JY Add
R1730 Resistor – VRS-CY1JF470JY Add
R1731 Resistor – VRS-CY1JF102JY Add
R1736 Resistor – VRS-CY1JF102JY Add
R1752 Resistor VRS-CY1JF470JY – Delete
R1773 Resistor VRS-CY1JF000JY – Delete
R1774 Resistor VRS-CY1JF470JY – Delete
R1775 Resistor VRS-CY1JF103JY – Delete
R2303 Resistor VRS-CY1JF000JY – Delete
CABINET AND MECHANICAL PARTS
Please refer to a Parts list.
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list.

LC-32GD8EA/RUA, LC-32BT8EA/RUA
ii
LC-32GD8EA/RUA, LC-32BT8EA/RUA Service Manual
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
• Plug the AC cord directly into a 220~240 volt AC outlet. (Do not use
an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
• A true RMS reading multimeter should be used for this test, espe-
cially where the equipment uses a switch mode power supply
which may result in very non-sinusoidal leakage current.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 1.05 peak (this corresponds to 0.7 mA. peak AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD colour television have
special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
For continued protection, replacement parts must be identical to those
used in the original circuit.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
CAUTION: FOR CONTINUED PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
F701 (4A / AC250V)
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
0.15 µ F
TEST PROBE

LC-32GD8EA/RUA, LC-32BT8EA/RUA
iii
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder
• “ALL PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals.
The alphabetical character following LF shows the type of lead-free solder.
Example:
• For the Inverter PWB Units the type used in nickel, so they are marked as LFn.
Using lead-free wire solder
• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PARTS CODE PRICE
RANK
PART
DELIVERY DESCRIPTION
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
Indicates lead-free solder of tin, silver and copper.
Indicates lead-free solder of tin, silver and nickel.

LC-32GD8EA/RUA, LC-32BT8EA/RUA
1 – 1
LC-32GD8EA/RUA, LC-32BT8EA/RUA Service Manual
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS
Item
Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV
Function
CCIR (B/G, I, D/K, L, L㧘
TV-Standard
LCD panel
Number of dots 3,147,264 dots (1366 768 3 dots)
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
VHF/UHF E2-E69ch, F2-F10ch, I21-I69ch, IR A-IR Jch, (Digital: E5-E69ch)
CATV Hyper-band, S1-S41ch
TV-Tuning System Auto Preset 99 ch, Auto Label, Auto Sort
STEREO/BILINGUAL NICAM/A2
Receiving
Channel
Brightness 450 cd/m2
Viewing angles H : 176qV : 176q
Audio amplifier 10W 2
Speaker 130 mm 60 mm
Terminals
9 pin MINI-DIN male connector
EXT 2
EXT 3 S-VIDEO (Y/C input), RCA pin (AV input)
Rear
RS-232C
UHF/VHF 75 Din type (Analogue & Digital)
SCART (AV input/output, Y/C input, RGB input, AV Link)
Antenna input
EXT 5 HDMI,˴3.5 mm jack (Audio input)
OSD language English/German/French/Italian/Spanish/Dutch/Swedish/Portuguese/Finnish/Turkish/Greek/
Russian/Polish
Power Requirement AC 220-240 V, 50 Hz
Power Consumption
Weight
32" LCD COLOUR TV,
Model: LC-32GD8EA, LC-32GD8RUA, LC-32BT8EA, LC-32BT8RUA
32" Advanced Super View &
BLACK TFT LCD
17 kg (Display only),
19 kg (Display with stand)
151 W (0.9 W Standby)
(Method IEC60107)
OUTPUT RCA pin (Audio)
Headphones 3.5 mm jack (Audio output)
EXT 1 SCART (AV input, Y/C input, RGB input, TV output)
EXT 4 3.5 mm jack (Audio input), 15 pin mini D-sub (PC/Component)
C. I. (Common Interface) EN50221, R206001
Digital DVB-T (2K/8K OFDM)
Analogue
Operating temperature 0to + 40
(
•

LC-32GD8EA/RUA, LC-32BT8EA/RUA
2 – 1
LC-32GD8EA/RUA, LC-32BT8EA/RUA Service Manual
CHAPTER 2. DIMENSIONS
[1] DIMENSIONS
804.0
356.0
539.0
699.6
388.5
636.0
575.0
200.0
119.2
115.7
394.3
61.0
200.0
115.0
88.1 183.3
Unit: mm

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 1
LC-32GD8EA/RUA, LC-32BT8EA/RUA Service Manual
CHAPTER 3. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIAGRAM
1. VOLTAGE MEASUREMENT CONDITION:
1) The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 120V. Signals are fed by a color bar signal
generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester.
2. INDICATION OF RESISTOR & CAPACITOR:
RESISTOR
1) The unit of resistance "Ω" is omitted.
(K=kΩ=1000Ω, M=MΩ).
2) All resistors are ± 5%, unless otherwise noted.
(K= ± 10%, F= ± 1%, D= ± 0.5%)
3) All resistors are 1/16W, unless otherwise noted.
CAPACITOR
1) All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2) All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH " " ( ) ARE IMPORTANT
FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO
REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAIN-
TAINING THE SAFETY AND PERFORMANCE OF THE SET.

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 2
[2] MAIN Unit
•MAINUnit-1
A
C
B
D
E
F
G
H
12345678910

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 3
10 11 12 13 14 15 16 17 18 19

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 4
•MAINUnit-5
A
C
B
D
E
F
G
H
12345678910

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 5
10 11 12 13 14 15 16 17 18 19

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 6
•MAINUnit-6
A
C
B
D
E
F
G
H
12345678910

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 7
10 11 12 13 14 15 16 17 18 19

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3 – 8
MEMO

PARTS GUIDE
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
LC-32GD8EA/RUA, LC-32BT8EA/RUA
Note:
The reference numbers on the PWB
are arranged in alphabetical order.
No. SY6Z3LC32D8EA
LC-32GD8EA/RUA
LC-32BT8EA/RUA
MODELS
PartsGuide
[1] PRINTED WIRING BOARD
ASSEMBLIES (NOT
REPLACEMENT ITEM)
[2] LCD PANEL (NOTE: THE PARTS
HERE SHOWN ARE SUPPLIED AS
AN ASSEMBLY BUT NOT
INDEPENDENTLY.)
[3] DUNTKD890FM28 (MAIN Unit)
[4] CABINET AND MECHANICAL
PARTS
[5] SUPPLIED ACCESSORIES
[6] PACKING PARTS (NOT
REPLACEMENT ITEM)

LC-32GD8EA/RUA, LC-32BT8EA/RUA
2
NO. PARTS CODE PRICE
RANK
NEW
MARK
PART
DELIVERY DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM)
NDUNTKD890FM28 CD R MAIN Unit
[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPEN-
DENTLY.)
NR1LK315T3LZ4BX EE R32" LCD Panel Module
[3] DUNTKD890FM28 (MAIN Unit)
C1747 VCCCCY1HH101JY AA R Capacitor, 100p 50V Ceramic
C1748 VCCCCY1HH101JY AA R Capacitor, 100p 50V Ceramic
C1749 VCKYCY1HB221KY AA R Capacitor, 220p 50V Ceramic
C1750 VCCCCY1HH101JY AA R Capacitor, 100p 50V Ceramic
C1751 VCCCCY1HH101JY AA R Capacitor, 100p 50V Ceramic
C1752 VCCCCY1HH101JY AA R Capacitor, 100p 50V Ceramic
IC1905 VHISII9021+-1Q BC R IC, SII9021CTU
IC1905 VHISII9023+-1Q BD R IC
P1701 QPLGNA342WJZZY AD R Plug, 8pins (LB)
P2305 QPLGNA493WJZZY AM R Plug, 32pins (LV)
R1715 VRS-CY1JF470JY AA R Resistor, 47 1/16W Metal Oxide
R1717 VRS-CY1JF470JY AA R Resistor, 47 1/16W Metal Oxide
R1718 VRS-CY1JF470JY AA R Resistor, 47 1/16W Metal Oxide
R1730 VRS-CY1JF470JY AA R Resistor, 47 1/16W Metal Oxide
R1731 VRS-CY1JF102JY AA R Resistor, 1k 1/16W Metal Oxide
R1736 VRS-CY1JF102JY AA R Resistor, 1k 1/16W Metal Oxide

LC-32GD8EA/RUA, LC-32BT8EA/RUA
3
[4] CABINET AND MECHANICAL PARTS
23
1
38
1-1
1-7
1-8
1-8
1-7
1-9
1-9
1-5
1-5
1-4
1-3 1-2
1-6
1-6
1-12
1-12
1-11
1-16
1-16
1-13
1-14
1-15
1-10
39
6
952
52
10
52
52
61
52
11
10
16
45
9
847
51
52 31
31
52
52
46
41
40
32
42
44
58
58
58
58
58
36
24 24
48
33 59
53
43
21
18
26
15
51
19
20
34
60
54
30
35
29
12 52
52
57
4
5
49
55
27
7
14
50
13
54
55
256
56
56
37
3
3-3
3-5
2-1
2-2
3-4
3-2
3-1
17
17
25
61

LC-32GD8EA/RUA, LC-32BT8EA/RUA
4
NO. PARTS CODE PRICE
RANK
NEW
MARK
PART
DELIVERY DESCRIPTION
[4] CABINET AND MECHANICAL PARTS
1CCABAB441WJ01 S Cabinet A Ass'y [LC32-GD8EA/RUA]
1CCABAB441WJ02 S Cabinet A Ass'y [LC32-BT8EA/RUA]
1-1 Not Available - - Cabinet A
1-2 GCOVAB478WJSA S R/C LED Cover
1-3 HBDGBA056WJSA S SHARP Badge
1-4 LHLDW1033PEZZ AA R Wire Holder for SP/RA Wire
1-5 PSPAHA607WJZZ S Mask Side spacer, x2
1-6 PSPAHA608WJZZ S Mask Top/Bottom Spacer, x2
1-7 PSPAHA786WJZZ S Top Corner Spacer, x2
1-8 PSPAHA790WJZZ S Bottom Corner spacer, x2
1-9 PSPAZB211WJZZ N S Spacer for Speaker, x4
1-10 QCNW-E233WJQZ S Connecting Cord (RA)
1-11 QCNW-E800WJQZ N S Connecting Cord (SP)
1-12 RCORF0103CEZZ AK R Ferrite Core for LED/Speaker Wire, x2
1-13 RSP-ZA184WJN1 N S Speaker (L)
1-14 RSP-ZA184WJN2 N S Speaker (R)
1-15 XEBS930P08000 AA R Screw for LED PWB Unit, x2
1-16 LX-HZA003WJFN AC R Screw for Speaker, x2
2CCABBA861WJ01 BK S Cabinet B Ass'y
2-1 Not Available - - Cabinet B
2-2 LHLDWA055WJKZ AC R Wire Holder for AC Code
3CCOVAB480WJ01 S Top Cover Ass'y
3-1 Not Available - - Top Cover
3-2 JBTN-A524WJKA N S Power Button
3-3 JBTN-A525WJKA N S Operation Button
3-4 MSPRCA068WJFW N S Spring for Power Button
3-5 XEBS930P08000 AA R Screw for PWB, x3
4CDAI-A290WJ01 N S Stand Support Ass'y [LC32-GD8EA/RUA]
4CDAI-A290WJ03 N S Stand Support Ass'y [LC32-BT8EA/RUA]
5CDAI-A287WJ01 N S Stand Base Ass'y [LC32-GD8EA/RUA]
5CDAI-A287WJ05 N S Stand Base Ass'y [LC32-BT8EA/RUA]
6R1LK315T3LZ4BX EE R32" LCD Panel Module
7GCOVAB488WJKA S Stand Cover
8HINDPC224WJSA N S Model Label [LC-32GD8EAE/EAK/EAF]
8HINDPC225WJSA N S Model Label [LC-32GD8EAI]
8HINDPC226WJSA N S Model Label [LC-32GD8RUA]
8HINDPC230WJSA N S Model Label [LC-32BT8EAE/EAK/EAF]
8HINDPC231WJSA N S Model Label [LC-32BT8EAI]
8HINDPC232WJSA N S Model Label [LC-32BT8RUA]
9LANGKA638WJFW S LCD Angle-A, x2
10 LANGKA639WJFW S LCD Angle-B, x2
11 LANGKA672WJFW S LCD Angle-C, x1
12 LANGTA263WJN1 S Center Angle (L)
13 LANGTA266WJN1 S Stand Angle
14 LANGTA267WJN1 S Center Angle (R)
15 LCHSMA324WJZZ BA R Chassis Tray
16 LHLDW1033CE00 AA R Wire Holder, x1
17 LHLDW1123GEZZ AB R Wire Holder, x2
18 LHLDW1173CEZZ AD R Wire Holder, x2
19 LHLDW1205CEZZ AC R Wire Holder, x2
20 LHLDWA055WJKZ AC R Wire Holder, x1
21 LHLDWA137WJZZ AB R Wire Holder, x2
23 PCUSGA009WJKZ S Cushion Spacer, x1
24 PFLT-A004WJZZ AE R Felt Sheet, x2
25 PMLT-A255WJZZ AD R Spacer, x1
26 PMLT-A315WJZZ AP R Spacer, x2
27 PSLDMA584WJZZ AE R Shield
29 PSLDMA877WJFW S Control PWB Unit Shield
30 PSLDMA943WJFW AK R Digital PWB Shield
31 PSPAHA902WJZZ S Spacer, x2
32 DUNTKD890FM28 CD R MAIN Unit
33 DUNTKD604FM10 BM R AV Unit
34 DUNTKD605FM14 BU R POWER Unit
35 DUNTKD628FM01 BY R DIGITAL Unit
36 CKITKD609FM01 BN S DIGITAL TUNER Unit
37 DUNTKD606FMV0 AK R OPERATION Unit
38 DUNTKD607FMV0 AQ R R/C, LED Unit
39 QCNW-E232WJQZ AG R Connecting Cord (KM)
40 QCNW-E609WJQZ AH R Connecting Cord (SH)
41 QCNW-E237WJPZ S Connecting Cord (LV)
42 QCNW-E235WJQZ AN R Connecting Cord (LA)
43 QEARPA212WJFW AE R Ground Part
44 QEARZA096WJFW S Ground Part
45 RCORFA023WJZZ AK N R Ferrite Core
46 QCNW-F185WJQZ AN R Connecting Cord (LB)
47 Not Available - - Serial No Label
48 LX-WZA042WJZZ S Washer
49 LX-BZA146WJF7 AC R Screw for Stand Ass'y, x4
50 LX-BZA147WJF7 N S Screw for Stand to Set, x4
51 XBBS930P06000 AA R Screw, x10
52 XBPS730P06WS0 AA R Screw, x17
53 XBPS830P06000 AA R Screw for HDMI
54 XEBS930P08000 AA R Screw, x4
55 XEBS940P16000 AB R Screw, x11
56 XEBSN40P10000 AB R Screw, x5

LC-32GD8EA/RUA, LC-32BT8EA/RUA
5
NO. PARTS CODE PRICE
RANK
NEW
MARK
PART
DELIVERY DESCRIPTION
[5] SUPPLIED ACCESSORIES
NO. PARTS CODE PRICE
RANK
NEW
MARK
PART
DELIVERY DESCRIPTION
57 XJPS730P04WS0 AB R Screw, x2
58 XJPS730P08WS0 AA R Screw, x19
59 RCORFA064WJZZ N S Ferrite Core for FPC Wire, x2
60 GCOVAB586WJKA S PC Card Cover
61 XBBS740P06000 AA R Screw, x2
[5] SUPPLIED ACCESSORIES
X1 LHLDW0110CESB AF R Cable Clamp
X2 LHLDWA083WJ00 AD R Cable Band
!
X3 QACCBA073WJPZ S AC Cord [LC-32BT8EAK, LC-32GD8EAK]
!
X3 QACCKA021WJPZ N S AC Cord [LC-32BT8EAE/EAF/EAI/RUA, LC-32GD8EAE/EAF/EAI/RUA]
X4 QCNWGA075WJPZ AU R 3 RCA to 15-pin D-sub adapter
X5 RRMCGA472WJSA S Remote Control Unit [LC-32GD8EA/RUA]
X5 RRMCGA490WJSA S Remote Control Unit [LC-32BT8EA/RUA]
X6 TGAN-A077WJZZ S Guarantee Card [LC-32BT8RUA, LC-32GD8RUA]
X6 TGAN-A342WJZZ S Guarantee Card [LC-32BT8EAK, LC-32GD8EAK]
X6 TGAN-A512WJZZ S Guarantee Card [LC-32BT8EAK, LC-32GD8EAK]
X7 TINS-C997WJZZ N S Operation Manual [LC-32BT8EAE/EAK/EAF/EAI, LC-32GD8EAE/EAK/EAF/EAI]
X7 TINS-C998WJZZ N S Operation Manual [LC-32BT8EE/EF, LC-32GD8EE/EF]
X7 TINS-D001WJZZ N S Operation Manual [LC-32BT8EAF, LC-32GD8EAF]
X8 TINS-C999WJZZ N S Operation Manual [LC-32BT8EAE, LC-32GD8EAE]
X9 Not Available - - "AAA"size Battery, x2
X10 CDAI-A287WJ02 N S Stand Unit [LC32-GD8EA/RUA]
X10 CDAI-A287WJ06 N S Stand Unit [LC32-BT8EA/RUA]
[4] CABINET AND MECHANICAL PARTS
3 RCA to 15-pin D-sub adapter
Remote Control Unit
X5
Cable Clamp
X1
Cable Band
X2
AC Cord
The forms of a plug differ
in some countries.
X3
X4 X10
Stand Unit

LC-32GD8EA/RUA, LC-32BT8EA/RUA
6
[6] PACKING PARTS (NOT REPLACEMENT ITEM)
S6
S6
S11
S12
S6
S1
S9
S9
S8
S4
S5
S7
S10
S2
S3