Sharp Carousel R-820BC User manual

R-820BC
MODEL R-820BC
DOUBLE GRILL
CONVECTION
MICROWAVE OVEN
S2401R820BPW/
SUPPLEMENTAL SERVICE MANUAL
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens con-
tain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Recti-
fier Assembly, High Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ......................................................................................................INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD AND WARNING ............................................................................................................................... 3
PICTORIAL DIAGRAM .......................................................................................................................................... 4
POWER UNIT CIRCUIT ........................................................................................................................................ 5
PARTS LIST .......................................................................................................................................................... 6
PACKING AND ACCESSORIES ........................................................................................................................... 8
This is a supplemental Service Manual for Model R-820BC. This model is quite similar to base model R-820BW. Use
this supplemental manual together with the Base Model Service Manual (Refer No. is S5812R820BPW/) for complete
operation, service information, etc..
CONVECTION
2
GRILL

R-820BC
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's
Center for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.

R-820BC
1
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of pro-
ducing very high voltage and current, contact with
following parts
may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Trans-
former, Magnetron, High Voltage Rectifier Assem-
bly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Before Servicing
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the high-
voltage capacitor (that is the connecting lead of the high-
voltage rectifier) against the chassis with the use of an
insulated screwdriver.
Whenever troubleshooting is performed the power supply
must be disconnected. It may in, some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and re-
examine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and microwave leakage test should be carried out.
Don't Touch !
Danger High Voltage

R-820BC
2
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission
in excess of 5 mW/cm2at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard
for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5˚C (68˚F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.)
and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.

R-820BC
3
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
SERVICE MANUAL
DOUBLE GRILL
CONVECTION
MICROWAVE OVEN
R-820BC
FOREWORD
This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service
Information for the SHARP MICROWAVE OVEN, R-820BC.
The model R-820BC is quite similar to base model R-820BW (Refer No. is S5812R820BPW/).
It is recommended that service personnel carefully study the entire text of this manual and the based model's manual so that
they will be qualified to render satisfactory customer service.
Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and
microwave radiation hazard.
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service personnel.
DANGER
Certain initial parts are intentionally not grounded and present a risk of electrical shock only during servicing.
Service personnel - Do not contact the following parts while the appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage
Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than 250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave exposure, by themselves, or when they are damaged,
loosened or removed.

R-820BC
4
6
45
123
6
45
123
A
B
C D E F
G H
A
B
C D E F
G H
Figure S-1. Pictorial Diagram
RED
RED
WHT
WHT
WHT
THERMAL
CUT-OUT
(OVEN)
OVEN LAMP
& SOCKET THERMAL
CUT-OUT
125°C(MAG.)
FAN MOTOR
CONVECTION
MOTOR
WHT
BLK
GRY
RED
BRN
WHT
HIGH VOLTAGE COMPONENTS
MAGNETRON
H.V.WIRE A H.V.
CAPACITOR
H.V.
RECTIFIER
H.V. WIRE B
POWER
TRANSFORMER
GRN
WHT
BLK
WHT
BLK
POWER SUPPLY
CORD
WHT
COM
WHT
WHT
RED
WHT
N.C.
N.O.
COM.
GRILL HEATER
THERMISTOR
BOTTOM HEATER
GRY
ORG
RED
WHT
CN-B
1
3
2
CN-B
CN-D
SP1
T1
15
RY6
RY2
RY4
RY3
WHT
CONTROL PANEL
WHT
WHT
WHT
BLK
WHT
WHT
BLK
TURNTABLE
MOTOR
MONITOR
SWITCH
GRY
WHT
2
3
4
5
1
ORG
RED
GRY
2
1GRN
GRY
CN-A
CN-A
RY5
CN-D
CN-C
CN-C
CN-G
ORG
ORG
ORG
BRN
NEUTRAL
HOT
EARTH
RY1
BLK
GRN
GRY
N.O.
COM.
DOOR SENSING SWITCH
SECONDARY
INTERLOCK
SWITCH
RED
RED
BRN
ORG
BRN
BLK
ORG
BLK
ORG
BLK
FUSE &
HOLDER
PRIMARY
INTERLOCK
RELAY
2
3
1 BLK
BLK
NOTE:
Hot (RED) wire must be
connected to the terminal
with blue mark on the
oven light socket.
NOTE:
The neutral (WHT) wire must be
connected to the terminal with "N"
mark on the power supply cord.
BLUE MARK

R-820BC
5
6
45
123
6
45
123
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
Figure S-2. Power Unit Circuit
+
–
+
–
+
–
COM
N.O.
COM
N.O.
COM
N.O.
COM
N.O.
A 3
OVEN LAMP
TURNTABLE
MOTOR
BOTTOM
HEATER
TOP
HEATER
MICRO
DOOR SWITCH
OVEN THERMISTOR
AC120V
60Hz
LED
GND
VC
VA
VR
INT
BUZZER
FAN MOTOR
CONVECTION
MOTOR
N.C.
OVEN
THERMISTOR
N.C.
MICRO
OVEN LAMP
TURNTABLE
MOTOR
BOTTOM
HEATER
TOP
HEATER
DOOR
SWITCH
FAN MOTOR
CONVECTION
MOTOR
Q2 2SB1238
R4 27
R5 4.7k
R3 510 1/2w
R2 510 1/2w
RY5
RY6
RY4
Q3
KRC243M
C5
10µ/35v
RY3
RY2
R6 3.3k
SP1
D5
D1
D1-4
1N4002
T1
D2
D4
c
d
ab
D3
4
6
1
8
VRS1
(J1)
C1 0.1µ/50v C3 0.1µ/50v
D12D11
RY1
D7D10D9D8
C4 10µ/35v C2 470µ/50v
10G471K
D6
A 1
B 2 B 1D 3 D 1
C12
C13
C17
C 7
C11
C 8
C14
C 6
C16
C15
C 5
C 4
C 9
C 1
C 3
C 2
C10
NOTE : IF NOT SPECIFIED, 1/4w ±5%
: IF NOT SPECIFIED, 1SS270A
A 5

R-820BC
6
*
*
*
*
∆*
∆*
PARTS LIST
Note: The parts marked “∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V.
REF. NO. PART NO. DESCRIPTION Q'TY CODE
ELECTRIC PARTS
1- 1 QSW-MA110WRE0 Secondary interlock switch / door sensing switch 2 AH
1- 1 QSW-MA131WRE0
Secondary interlock switch / door sensing switch (Interchangeable) 2AG
1- 2 FFS-BA021WRK0
Monitor fuse and monitor switch (V-16G-2C25(R)) assembly 1AL
1- 3 RMOTDA140WRE0 Turntable motor 1 AV
1- 3 RMOTDA231WRE0 Turntable motor (Interchangeable) 1 AR
1- 3 RMOTDA188WRE0 Turntable motor (Interchangeable) 1 AS
1- 4 FH-DZA025WRK0 High voltage rectifier assembly 1 AN
1- 5 RC-QZA173WRE0 High voltage capacitor (Interchangeable) 1 AX
1- 5 RC-QZA211WRE0 High voltage capacitor 1 AV
1- 6 RMOTEA370WRE0 Fan motor 1 AX
1- 7 QFSHDA009WRE0 Fuse holder 1 AG
1- 7 QFSHDA010WRE0 Fuse holder (Interchangeable) 1 AD
1- 8 FACCDA074WRE0 Power supply cord 1 AW
1- 9 FH-HZA063WRE0 Thremistor 1 AP
1-10 RMOTEA372WRE0 Convection motor 1 AX
1-11 QTANNA017WRW0 Short terminal 1 AD
1-12 RHET-A223WRE0 Grill heater (Top heater) 2 AV
1-13 RHET-A209WRE0 Bottom heater 1 BA
1-14 RLMPTA030WRE0 Oven lamp 1 AE
1-15 QSOCLA021WRE0 Oven lamp socket 1 AG
1-16 RTHM-A109WRE0 Thermal cut-out 170 deg. 1 AM
1-17 RTHM-A078WRE0 Thermal cut-out 125 deg. 1 AK
1-18 RTRN-A568WRE0 Power transformer 1 BP
1-19 RV-MZA222WRE0 Magnetron 1 BN
1-19 RV-MZA267WRE0 Magnetron (Interchangeable) 1 BL
CABINET PARTS
2- 1 GCABDA097WRW0 Back plate 1 AW
2- 2 GCABUA886WRPZ Outer case cabinet 1 BE
2- 3 GDAI-A305WRW0 Base plate 1 AX
2- 4 GLEGPA074WRE0 Leg 2 AC
CONTROL PANEL PARTS
3- 1 DPWBFB795WRK0 Power unit 1 BD
3- 1A QCNCMA234DRE0 3-pin connector (CN-A) 1 AC
3- 1B QCNCMA275DRE0 2-pin connector (CN-B) 1 AB
3- 1C FW-VZA238DRE0 9pin wire harness (WH-1, WH-2) 2 AK
3- 1D QCNCMA410DRE0 2-pin connector (CN-D) 1 AB
C1 RC-KZA087DRE0 Capacitor 0.1 uF 50V 1 AA
C2 VCEAB31HW477M Capacitor 470 uF 50V 1 AE
C3 RC-KZA087DRE0 Capacitor 0.1 uF 50V 1 AA
C4-5 VCEAB31VW106M Capacitor 10 uF 35V 2 AA
D1-4 RH-DZA006PRE0 Diode (1N4002) 4 AD
D5-7 VHD1SS270A/-1 Diode (1SS270A) 3 AA
D8-12 VHD1SS270A/-1 Diode (1SS270A) 5 AA
Q2 VS2SB1238//-3 Transistor (2SB1238) 1 AA
Q3 VSKRC243M//-3 Transistor (KRC243M) 1 AB
R2-3 VRD-B12HF511J Resistor 510 ohm 1/2W 2 AB
R4 VRD-B12EF270J Resistor 27 ohm 1/4W 1 AB
R5 VRD-B12EF472J Resistor 4.7k ohm 1/4W 1 AA
R6 VRD-B12EF332J Resistor 3.3k ohm 1/4W 1 AA
RY1 RRLY-A080DRE0 Relay (OJ-SH-124LM) 1 AG
RY2-4 RRLY-A076DRE0 Relay (OMIF-S-124LM) 3 AK
RY5 RRLY-A080DRE0 Relay (OJ-SH-124LM) 1 AG
RY6 RRLY-A076DRE0 Relay (OMIF-S-124LM) 1 AK
SP1 RALM-A014DRE0 Buzzer (PKM22EPT-THAI) 1 AG
T1 RTRNPA124DRE0 Transformer 1 AQ
VRS1 RH-VZA032DRE0 Varistor (10G471K) 1 AE
3- 2 DPWBFB794WRK0 CPU unit 1 BC
3- 3 DPNLCB893WRKZ Control panel frame with key unit 1 BB
3- 3-1 JBTN-B267WRTZ Open button 1 AN
3- 3-2 MSPRCA050WRE0 Open button spring 1 AB
3- 3-3 FUNTKB149WREZ Key unit 1 AX
3- 3-4 TCAUAA076WRR0 User caution label 1 AB
3- 4 LHLD-A185WRF0 LCD holder 1 AL
3- 5 PSHEPA626WRE0 LED sheet 1 AF
3- 6 ************* This user caution label has been changed to 3-3-4.

R-820BC
7
REF. NO. PART NO. DESCRIPTION Q'TY CODE
∆
∆
∆
∆
∆
*
3- 7 XEPSD30P08XS0 Screw; 3mm x 8mm 4 AA
OVEN PARTS
4- 1 ************* Oven cavity (Not a replaceable part) 1 --
4- 2 PHOK-A106WRF0 Latch hook 1 AL
4- 3 FDUC-A337WRK0 Air duct assembly 1 BH
4- 4 PCOVPA340WRW0 Sub back plate 1 AQ
4- 5 LANGQA478WRP0 Turntable motor angle 1 AP
4- 6 MSPRTA186WRE0 Plate spring 1 AE
4- 7 NCPL-A051WRE0 Turntable motor shaft 1 AN
4- 8 PSPA-A109WRE0 Spacer 1 AB
4- 9 LBNDKA136WRP0 HV capacitor holder 1 AQ
4-10 NFANJA041WRE0 Fan blade 1 AF
4-11 PDUC-A697WRF0 Fan duct 1 AM
4-12 GCOVHA388WRW0 Bottom heater cover 1 AF
4-13 GLEGPA071WRF0 Leg 1 AG
4-14 LANGFA191WRW0 Chassis support 1 AN
4-15 LANGQA489WRP0 Thermistor angle 1 AW
4-16 LFLG-A030WREZ Bearing 1 AM
4-17 MLEVPA226WRF0 Switch lever 1 AF
4-18 MSPR-A004WRE0 Heat seal spring 2 AF
4-19 PCOV-A011WRP0 Bottom heater angle 2 AM
4-20 PCOVPA339WRE0 Waveguide cover 1 AF
4-21 PCUSGA385WRP0 Cushion 1 AH
4-22 PCUSUA190WRP0 Cushion 1 AC
4-23 PCUSUA191WRP0 Cushion 1 AC
4-24 PDUC-A691WRF0 Air intake duct 1 AG
4-25 PDUC-A692WRP0 Exhaust duct 1 AS
4-26 PDUC-A784WRWZ Air guide 1 AP
4-27 PGLSPA518WRE0 Light glass 1 AZ
4-28 PPACGA050WRE0 Cushion 1 AE
4-29 PREFHA061WRW0 Reflector 1 BE
4-30 PSHEPA487WRE0 Heater film 1 AA
4-31 PSKR-A331WRP0 Air separate angle 1 AY
4-32 MSPRCA113WRE0 H-spring 2 AC
4-33 PCUSGA420WRP0 Cushion 1 AE
4-34 NFANMA047WRP0 Convection fan 1 AX
4-35 NFANMA048WRP0 Cooling fan 1 AX
4-36 PCUSUA499WRP0 Cushion 1 AC
4-37 PDUC-A707WRW0 Convection duct 1 AR
4-38 PFPF-A210WRE0 Thermal insulation 1 AM
4-39 PPIPFA030WRE0 Pipe 1 AK
4-40 PSKR-A339WRP0 Convection air angle 2 AX
4-41 PSKR-A345WRW0 Convection motor angle A 1 AU
4-42 PSKR-A346WRW0 Convection motor angle B 1 AR
4-43 PSLDHA140WRW0 Convection thermal cover 1 AQ
4-44 PCUSGA389WRP0 Cushion 1 AG
DOOR PARTS
5- 1 DDORFA857WRK0 Door panel assembly 1 BB
5- 2 GWAKPA948WRRZ Door frame 1 AZ
5- 3 LSTPPA176WRF0 Latch head 1 AN
5- 4 LSTPPA177WRF0 Glass stopper 1 AF
5- 5 MSPRTA187WRE0 Latch spring 1 AC
5- 6 PGLSPA513WRE0 Front door glass 1 AV
5- 7 ************* These screws have been changed to 5-8. 0
5- 8 XCPSD40P08000 Screw : 4mm x 8mm 6 AA
5- 9 GCOVHA387WRF0 Choke cover 1 AS
MISCELLANEOUS
6- 1 FAMI-A104WRM0 Rack 1 AQ
6- 2 TCAUAA145WRR0 Earth caution 2 AG
6- 3 FSRAHA063WRYZ Turntable support 1 AK
6- 4 NTNT-A097WRE0 Turntable 1 BB
6- 5 TCAUAA200WRR0 Monitor caution 1 AB
6- 6 TINSEB034WRRZ Instruction book 1 AM
6- 7 FW-VZB045WRE0 Switch harness 1 AG
6- 8 FW-VZB872WREZ Main wire harness 1 BB
6- 9 QW-QZA213WRE0 High voltage wire B 1 AF
6-10 LHLDWA011WRE0 Purse lock M 1 AB
6-11 TCAUAA201WRR0 DHHS caution label 1 AC
6-12 TCAUAA240WRR0 Screw caution 1 AC
6-13 TLABMA978WRRZ Menu label 1 AL

R-820BC
8
REF. NO. PART NO. DESCRIPTION Q'TY CODE
6-14 TLABNB032WRRZ Touch guide 1 AK
SCREWS,NUTS AND WASHERS
7- 1 XFPSD40P08K00 Screw : 4mm x 8mm 13 AA
7- 2 XEPSD40P25000 Screw : 4mm x 25mm 2 AA
7- 3 LX-EZA042WRE0 Special screw 2 AB
7- 4 LX-NZ0061WRE0 Flange nut 4 AA
7- 5 XBPWW30P05K00 Screw : 3mm x 5mm 2 AA
7- 6 XCTWW40P08000 Screw : 4mm x 8mm 8 AB
7- 7 XHPSD30P06000 Screw : 3mm x 6mm 1 AA
7- 8 XHTSD40P08RV0 Screw : 4mm x 8mm 3 AA
7- 9 XOTSD40P12RV0 Screw : 4mm x 12mm 13 AA
7-10 XOTSD40P12000 Screw : 4mm x 12mm 10 AA
7-11 ************* These line head screws have been changed to 7-9. 0 --
7-12 XOTSF40P08000 Screw : 4mm x 8mm 1 AA
7-13 XBTSD40P05000 Screw : 4mm x 5mm 2 AA
7-14 XNEUW40-32000 Nut : 4mm x 3.2mm 1 AA
7-15 XRESE40-06000 Ring : 4mm x 0.6mm 1 AA
7-16 XWHUW40-08000 Washer : 4mm x 0.8mm 1 AA
7-17 XWHUW48-08120 Washer : 4.8mm x 0.8mm 1 AA
7-18 XWSUW40-10000 Washer : 4mm x 1.0mm 1 AA
7-19 LX-CZA070WRE0 Special screw (Torx tamper proof screw) 2 AC
7-20 XCPSD40P08000 Screw : 4mm x 8mm 1 AA
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION
Order Parts from the authorized SHARP parts Distributor for your area.
Defective parts requiring return should be returned as indicated in the Service Policy.
PACKING AND ACCESSORIES
TRAY HOLDER
(SPADFA424WRE0)
TURNTABLE TRAY
RACK
LAMP CAUTION
TOUCH GUIDE
INSTRUCTION BOOK
TURNTABLE SUPPORT
TRAY PAD
(SPADPA577WRE0)
TOP PAD ASSEMBLY
(FPADBA381WRK0)
BOTTOM PAD ASSEMBLY
(FPADBA382WRK0)
WRAP COVER
(SSAKHA034WRE0)
DOOR PROTECTION SHEET
(SPADPA204WRE0)
PACKING CASE
FPAK-A505WRKZ
Not Replaceable Items.
FOAM SHEET
(SPAKHA012WREZ)
CABINET COVER
(SPAKHA009WRE0)
PLASTIC SHEET
(SPADPA616WREZ)