Sharp MP300CM Guide
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
1 of 9
For customer care call 1-800-865-2112
Installation and Assembly Manual:
Ceiling Mount for NP-PE506WL, NP-PE506UL, NP-PE456USL,
NP-MC453X, NP-MC423W, NP-ME453X, NP-ME423W, NP-ME403U,
NP-P474W, NP-P474U, NP-P554W, NP-P554U Projectors
Model: MP300CM
Features:
• ImageLockTM alignment prevents picture sag or drift
• Wrenchaccessslotforeasierushmountinstallations
• Exclusive aluminum track quick release Max UL Load Capacity: 50 lb (22.7 kg)
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 9
For customer care call 1-800-865-2112
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Extension Columns / Ceiling Plate ...................................................................................................................4
Installation to Wood Joist Ceilings..........................................................................................................................................5
Installation to Concrete Ceilings.............................................................................................................................................6
Attaching Adapter Plate to Projector.......................................................................................................................................7
Attaching Adapter Plate to Projector Mount............................................................................................................................8
Projector Alignment ................................................................................................................................................................9
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillips screwdriver
• drill
• 5/16"bitforconcretesurface
• 5/32"bitforwoodstuds
• level
NOTE: Read entire instruction sheet before you start installation and assembly.
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity. See page 1.
• If mounting to wood joist ceilings, make sure that mounting screws are anchored into the center of the joist. Use of
an"edgetoedge"studnderishighlyrecommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with
thehardwareincludedinthisproductasspeciedintheinstallationsheet.Tomountthisproducttoanalternative
supporting surface, contact Peerless customer care at 1-800-865-2112.
• This product was designed to be installed on the following ceiling construction only;
CEILING CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
xWood Joist None
xSolid Concrete None
Cinder Block Contact Customer Service
Brick Contact Customer Service
Otherorunsure? ContactCustomerService
WARNING
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 9
For customer care call 1-800-865-2112
Description Qty. Part #
A
projector mount assembly 1 054-2171
B4 mm security allen wrench 1 560-9646
C#10-32x3/8"serratedwasherheadsocketpinscrew 2 520-2151
D#10-32x1/4"socketpinscrew 1 520-2196
Eflat washer 2 540-1078
F#14 x 2.5 phillips hex head wood screw 2 5S1-015-C04
Gconcrete anchor 2 590-0320
A
A
adapter plate 1 055-2985
BB M4 x 16 mm serrated socket pin screw 3 510-2087
CC retaining spacer 3 590-2009
DD 2 mm allen wrench 1 560-1097
EE
connection block 1 580-4065
Parts List
NOTE:Actualpartsmayappearslightlydierentthanillustrated.
Before you start check the parts list to insure all of the parts shown are included.
C
A
DG
E F
CC
BB
B
DD
EE
AA
4
4
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 9
For customer care call 1-800-865-2112
Installation to Extension Column / Ceiling Plate
NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to
ceiling.
Screw projector mount assembly (A) onto extension column as shown in gure 1.1. Tighten swivel stop screw
againstextensioncolumn,ushmounttubeorreducerusing4mmsecurityallenwrench(B) as shown in gure
1.2.
NOTE: Swivelstopscrewisusedtojamagainstthreadsofextensioncolumn,ushmounttubeorreducerto
prevent any excess movement of projector mount assembly (A). Do not overtighten screw; overtightening screw
willdamagethreadsmakingitdiculttoseparateproducts.
Skip to step 4.
1
g. 1.1
g. 1.2
A
1-1/2"EXTENSIONCOLUMN
(SOLDSEPARATELY)
(ULLISTEDEXTORAECSERIES)
ARROWINDICATES
FRONTOFMOUNT
SWIVELSTOPSCREW
CMJ 455
(SOLDSEPARATELY)
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
5 of 9
For customer care call 1-800-865-2112
Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes.
Makesurethatthemountingholesareinthecenterofthewoodjoist.Drilltwo5/32"(4mm)dia.holestoa
minimumdepthof2.5"(64mm).Attachprojectormountassembly(A)withtwo#14x2.5"woodscrews(F) and
twoatwashers(E) as shown in gure 2.1 or gure 2.2 depending on joist orientation.
NOTE: Mounting slots on projector mount assembly allow for 30° (±15°) of swivel adjustment before fully securing
wood screws.
Tighten wood screws (F)using3/8"(10mm)socketwrench,phillipsscrewdriveror10mmopenendwrenchuntil
projector mount assembly (A)isrmlyattached.
Skip to step 4.
Installation To Wood Joist Ceilings
2
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tightenwoodscrewssothatprojectormountassemblyisrmlyattached,butdonotovertighten.Overtightening
can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder
is highly recommended.
• When installing Peerless ceiling mounts on a wood joist/beam covered with gypsum board (drywall), verify that the
joistsorbeamsareaminimumof2"x4"nominalsize.Donotinstallovergypsumboardthickerthan5/8".
WARNING
FF
A
WOODJOIST
FRONTOF
MOUNT
EE
WOODJOIST
A
ACCESSSLOTFOR
OPENENDWRENCH
ALLOWSTIGHTENING
OFWOODSCREW
g. 2.1 g. 2.2
ARROWONTOPOF
PROJECTORMOUNT
ASSEMBLYINDICATES
FRONTOFMOUNT
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
6 of 9
For customer care call 1-800-865-2112
g. 3.1
Installation to Concrete Ceilings
Place projector mount assembly (A) on ceiling
as a template and mark the center of the two
mountingholes.Drilltwo5/16"(8mm)dia.holes
toaminimumdepthof2-1/2"(64mm).Attach
projector mount assembly (A) using two concrete
anchors (G),twoatwashers(E), and two #14 x
2-1/2"woodscrews(F) as shown in gure 3.1.
NOTE: Mounting slots on projector mount
assembly allow for 30° (±15°) of swivel adjustment
before fully securing wood screws.
Tighten wood screws (F)using3/8"(10mm)socket
or open end wrench or phillips screwdriver until
projector mount assembly (A)isrmlyattached.
3
• WheninstallingPeerlessceilingmountsonaconcreteceiling,theceilingmustbeatleast8"thickwithaminimum
compressive strength of 2000 psi. Never attach concrete expansion anchors to concrete covered with plaster,
drywall,orothernishingmaterial.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
WARNING
• Tightenwoodscrewsrmly,butdonotovertighten.
Overtighteningcandamagethescrews,greatly
reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
G
F
E
A
CONCRETECEILING
ARROWONTOP
OFPROJECTOR
MOUNTASSEMBLY
INDICATESFRONT
OFMOUNT
1
3
G
Drill holes and insert anchors (G).
Place plate (A) over anchors (G) and secure with screws (F).
Tighten all fasteners.
2
G
A
F E
concrete
surface
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
7 of 9
For customer care call 1-800-865-2112
Align shoulder on connection block (EE) opposite
notch in adapter plate (AA). Attach adapter plate
(AA) to connection block (EE) using two #10-32 x
3/8"serratedwasherheadsocketpinscrews(C)
asshowningure4.1.Tightenscrewsusing4mm
allen wrench (B).
C
NOTCHINDICATES
FRONTOF
PROJECTOR
SHOULDER
Attaching Adapter Plate to Projector
g. 4.1
BB
Flip projector upside down and attach adapter plate (AA) using four serrated socket pin screws (BB) and retaining
spacers (CC) as shown below. Tighten using 4 mm allen wrench (B).
NOTE: Retaining spacers (CC) go between the projector and adapter plate (AA).
AA
CC
AA
EE
5
4
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
8 of 9
For customer care call 1-800-865-2112
Slide connection block (EE) with projector into projector mount assembly (A) as shown. Tighten captive screw to
secure projector to projector mount assembly (A).
IMPORTANT:Forsecurityinstallations,insertone#10-32x1/4"socketpinscrew(D) through projector mount
assembly (A) and into connection block (EE) as shown in detail 1. Tighten screw using 4mm security allen
wrench (B).
A
D
• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely
handle placement of the screen.
WARNING
Attaching Adapter Plate to Projector Mount
DETAIL 1
EE
7
A
FRONTOFMOUNT
CAPTIVE SCREW
ARROWINDICATES
FRONTOFMOUNT EE
6
ISSUED: 2010-01-10 SHEET #: 056-9034-9 (2023-04-20)
Visit the Peerless Web Site at www.peerlessmounts.com
9 of 9
For customer care call 1-800-865-2112
SCREWFORYAW(SWIVEL)STOP
(REFERTOSTEP1,INSTALLATION
TOEXTENSIONCOLUMNS,FIG.1.2)
KNOBFORROLL
ADJUSTMENT
KNOBFORPITCH
ADJUSTMENT
BACKOFMOUNT
ARROWINDICATES
FRONTOFMOUNT
To adjust yaw (swivel) for wood stud and concrete ceiling:Loosen wood screws (F)ifushmountedtowood
joists (page 5) or concrete ceilings (page 6), until projector mount can be rotated. Rotate mount to desired
position and retighten screws.
To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A)
indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and
turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for
easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
A
To prevent tampering with the pitch and roll adjustments:Tighten the two tamper resistant security screws
on the projector mount assembly using 4mm security allen wrench (B) to lock the pitch and roll adjustments as
shown below. Note:Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagethemount.
SIDE VIEW
Projector Alignment
8-1
TOLOCKPITCH,
TIGHTENTAMPER
RESISTANT
SECURITYSCREW
© 2023, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
• Do not adjust pitch or roll while tamper resistant security screws are fully engaged.
• Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly
or damage may occur.
CAUTION
8
Table of contents
Other Sharp Rack & Stand manuals
Sharp
Sharp MultiSync PN-ME652 Guide
Sharp
Sharp AN-65ST1 User manual
Sharp
Sharp AN-GR500H User manual
Sharp
Sharp AN-52AG6 User manual
Sharp
Sharp AN-WS350 User manual
Sharp
Sharp EBR5000W User manual
Sharp
Sharp MD-DR470H User manual
Sharp
Sharp AN-CM270 User manual
Sharp
Sharp AN-PR1500H User manual
Sharp
Sharp Carousel RK49S27F User manual
