SHEDorize 3 Tier Wall Shelf User manual

SHEDorize.com
[phone]
[e-mail]
contents
•20 - #10 3" white screws, #2 sq dr
•16 - #10 2.5" white screws, #2 sq dr
•26 - #8 1" black screws, #2 sq dr
•12 - #10 2" black screws, #2 sq dr
•6 - brackets
•3 - 48" shelves
•1 - 2" x 3" x 48" long cross piece
•2 - 2" x 3" corner braces (diagonal cut)
•4 - 23.5" vertical support wooden pieces
SHEDorize 3 Tier Wall Shelf, 48"
Instruction Manual for Sizes:
happy with our products?
Please help us spread the
word by leaving a review at:
www.SHEDorize.com
12" x 48" | 16" x 48" | 24" x 48"
Finished | Unfinished

SHEDorize.com
[phone]
[e-mail]
Setting Up Your SHEDorize 3 Tier Wall Shelf, 48"
CONFIRM THAT ALL PARTS ARE PRESENT
BEFORE BEGINNING ASSEMBLY.
1. Items to note before starting.
a. If you want to adjust your shelf spacing, you can do so by cutting the vertical
supports to your desired height.
2. Assemble bottom shelf and supports.
a. Put the first shelf on its side, install the 23.5" vertical support wooden
pieces by placing it on the mark on top of the shelf, and then put the short
black screws up through the bottom in the pre-drilled holes and fasten.
b. Place the corner brace with the diagonal cut underneath the vertical
support up against the plywood and put the short white screws in the pre-
drilled holes in the side of the shelf and fasten.
c. Place the corner braces with the diagonal cut on the mark of the 48" cross
piece, making sure the pre-drilled holes on the cross piece are towards the
top. Then, put the short white screws in the pre-drilled holes and fasten.
3. Attach the bottom shelf to the wall.
a. Figure out how far apart the studs are so you can fasten the steel brackets
to a stud. For example, if the studs are 16" or 24" on center, put the steel
brackets even on the end of the shelf and fasten with the short black
screws.
b. Find the studs and place a mark at 21.25" high. Take the shelf you just
assembled and put the long black screws through the steel bracket and
fasten into the stud.
c. Before going to the second shelf, make sure this shelf is level (at the same
height in the front as it is in the back). Then, put two long white screws
through the 48" cross piece into the studs.
It’s possible that the shelves may be
twisted when you unbox them. This is
normal due to the nature of lumber.
You will simply need to maneuver your
shelves to be level and fasten screws in
when the shelf is level.

SHEDorize.com
[phone]
[e-mail]
4. Install the second and third shelves.
a. Next, put a mark on the wall for the height of the next two shelves. For the second shelf,
measure up 24" from the top of the first shelf. For the third shelf, measure up 48" from the top
of the first shelf. (Again, as noted in step (1), you can adjust the height of the vertical supports.
If you do adjust the vertical supports, the measurements in this step will need to change,
according to what your custom lengths are.)
b. Take the second shelf and put two 23.5" vertical supports on both
marks on the top of the shelf. Then, put the short black screws up
through the bottom in the pre-drilled holes and fasten. Put the steel
brackets in the same place as you did with the first shelf. Install the
shelf onto the wall by setting the second shelf on top of the vertical
supports on the first shelf, and then put the long black screws through
the steel brackets and fasten into the stud. Then, put short white
screws in the pre-drilled holes of the vertical support piece beneath the second shelf, into the
side of the underside of the shelf.
c. Take the third shelf and put the steel brackets in the same place as you did with the other
shelves. Place this third shelf on top of the vertical supports on the second shelf and fasten the
steel brackets into the studs. Then, put short white screws in the pre-drilled holes of the
vertical support piece into the side of the underside of the shelf.
5. Complete installation.
a. Finally, once all previous steps have been completed, go in underneath each of the shelves
and install 2 long white screws through each of the shelves into each
stud. Please Note: This step is important.
Not to exceed 225 pounds per tier or 750 pounds overall.