ShelterLogic 25769 User manual

orPlease read instructions completely bef e assembly
Model #25769
12x30 CELEBRATION "2" DECORATIVE CANOPY
12
Anchors
10431
Description Qty. Part #
67" Swedged Rafter Poles 12 10042
76" Swedged Leg Poles 12 10043
69.6" Cross Poles 15 10244
(Top Bend, shallow bend)
3-Way Frame Connectors 2
4
10046
4-Way Frame Connectors 10048
(Side Bend, sharp bend)
3-Way Frame Connectors 10045
4-Way Frame Connectors 10047
Cover 1800202
Bolts 1/4" x 2 1/2" 18 10017
Nuts 1/4" 12 1010
Wing Nuts 67000
Foot Plates 12 10050
Bungee Cords 56 10066
Long Pins w/rings
12 10052
Short Pins w/rings
12 10051
4
8
05-25769-0C 03/03/08
ATTENTION: PINS
Pins are for legs and feet,
and are NOT needed
for any other part of the
Long Pins secure feet plates to legs.
Short Pins secure legs to side bends.
Recommended Tools
Adjustable
wrench
Ratchet with
7/16 "
Safety Glasses
Ladder
Rubber Mallet
Tape Measure
Before You Start
• 2 or more persons recommended
to assemble
• Estimated assembly time = 2 hours
Manufactured Under
U.S. Patents
D415,571 D409,310
D430,306 D414,564
Other Patents Pending
150 Callender Road
Watertown, CT 06795
800.524.9970
www.shelterlogic.com
PAGE 1
3802102
Truss

PAGE 2
Side Bend Connectors
(sharp bend)
Top Crest Connectors
(shallow bend)
10042
10244 10244 10244
10244 10244 10244
10244 10244 10244
10244 10244 10244
10244 10244 10244
10042
10046 10048 10045 10047
10042 10042
10042 10042
10042 10042
10042 10042
10042 10042
Assembly is easiest if you layout all parts as
shown. There are (12) #10042 Rafter Poles ,
they are swedged on both ends. The (15)
#10244 Cross Poles do not have swedged
ends. It is very important that you determine
which of the 3 & 4 way connectors are meant
for the sides and which are for the crest.
assembly together as shown in Fig. 1A. Assemble each side of the roof as shown in Fig. 2. Install #802102 truss
brace roof cables as shown in Fig. 2A.
Start with center, Fig. 1, using layout shown in diagram above. Bolt roof
Assemble Roof
Fig. 2
Fig. 1
Note: Install all carriage bolts
with nut toward center of frame.
10043
01010
10017
Fig. 1A
Place cover over frame so that the
grommeted portion is face down,
this allows the valance to wrap
around and cover the frame eaves.
Insert #10043 Leg Poles on one side of the frame, swedged
end up, then the end legs on that same side. Repeat for the
other side. Now you can secure the legs to the side bend
connectors and secure the cover with bungee cords.
10046
10045
10046
10045
10047 10047
10048
10045
10045
10047 10047
10048
10047 10047
10048
10047 10047
10048
10017
7000
Fig. 2A
802102
1. Frame Assembly
4. Attaching Legs
3. Place Cover

12 Short Pins are used to secure legs to side bend connectors.
Working inside, beneath the cover, begin with the corners. Insert the cord of the bungee-ball through the
grommet and around the Cross Pole, then around the ball. By doing this from the inside it will hide the bungee-ball
and give a cleaner look. When all 4 corners are secured, work from side to side to get an even fit.
To secure the valence corners wrap the
upper hook and loop tie just below the elbow.
Do the same for the lower hook and loop tie.
Note: this will keep the valence from rolling up
but still allow for movement.
Page 3
5.Securing legs
6.Securing cover

Locate a suitable location to place one anchor
as shown in the illustration into each of the base
feet until the round end of the anchor touches the
base feet.
Page 4
Insert Base Feet Plates onto
bottom of legs, be sure to line
up the pre-drilled hole in the leg
with the pre-drilled hole in the
base foot. Insert long pins all
the way through leg and foot,
to other side, secure with ring.
7.Attaching
&Securing base
feet
8.Anchoring