ShelterLogic 25730 User manual

Description Qty. Part #
Bungee Cords 50 10066
810462
04-25730-0C 07/16/07
Model #25730
Tent Pole 6
Guy Ropes 11' 104376
Rope Toggle 10436
10458
Tent Pole Swedged 610459
Side Wall 2 12082
"S" Hook
Clamp
4 10464
Tetherball 4 10465
6
Anchors 10447
6
Ropes 3' 104634
Wing Nut
Bolts 1/4" x 1 1/2"
70008
30258
WARNING!
Use CAUTION when assembling this unit.
Manufacturer requires the use of safety
goggles during assembly. Bungees are
under extreme tension and may snap out
of your hand and cause injury. Be aware
of poles over your head during assembly
that may not be secured, and could fall
and cause injury.
Do not assemble near electrical over head
wires.
Two or more persons are recommended to
assemble this shelter.Estimated assembly
time:3 hrs.
Manufactured Under
U.S. Patents
D415,571 D409,310
D430,306 D414,564
Other Patents Pending
150 Callender Road
Watertown, CT 06795
800.524.9970
www.shelterlogic.com
ATTENTION:
FOR MISSING OR
REPLACEMENT PARTS
OR
QUESTIONS
PLEASE CONTACT
CUSTOMER SERVICE:
1.800.524.9970
Assembly Manual Parts List
10'x20' Canopy Extension Kit
Step Ladder
Tape measure
Recommended Tools
Safety Glasses

STEP 1. ATTACH WINGS
PAGE 1
PARTY WING KIT TO THE
FRAME
# 10458
# 10459
STEP 2. PARTY TENT CONVERSION
After attaching the walls, assemble the six tent poles
as shown to the right. Lay these off to the side for later.
10436
Tie a knot in the end of each rope and thread it thru
the rope clamp and anchor. These anchor assemb-
lies will be used later.
Knot
Fig. A Fig. B
Cover
Twist this
way !
Cover
At the (4) corners of the canopy release the tension
on the corner ropes and remove them from the leg
poles, so the side valence is loose. Secure the loose
rope and "S" Hook to a bungee cord inside the roof
of the canopy.
Following figures A & B attach the ropes and "S" Hooks
provided in the kit to the ends of the canopy's main cover
using the clamps, bolts and nuts. The clamp should be
mounted approximately 6" to 10" up from the corner. Ins-
ert the "S" Hook into the corner upright and twist to tens-
ion the main cover.
NOTE: Be sure the clamp holds the rope inside the
pocket on the cover end.
Rope in
Pocket
6" 10"
Top
Bottom
Before You Start
• 4 or more persons recommended to assemble
• Estimated assembly time = 3 hours
CAUTION!!!
Bungee Cords are under extreme tension. Use Caution
when installing. The use of safety glasses is
recommended to prevent injury.
Walls attach to unit by Bungee Cords. Thread bungee cord
through grommets in wall and wrap around pole. If using more
than one wall, attach all the walls at the top first, then work your
way around the unit wrapping the bungee cords through both
corners of the walls and legs.
ATTENTION:
FOR MISSING OR
REPLACEMENT PARTS
OR QUESTIONS,
PLEASE CONTACT
CUSTOMER SERVICE:
1.800.524.9970

Page 2
# 10459
# 10458
Fig. D
Fig. D
TOP VIEW OF ANCHORING WING KIT
Wing Wing
While lifting one wing out and up at the middle
insert an extension pole into the tab at the middle
of the wing. Make a knot in the end of one of the
ropes and place it over the tab and pole end as
shown in Figures C & D. Place the anchor
securely in the ground about 3' from the
extension pole. (Fig. E)
Slide the rope clamp up the rope to tighten the wing.
Proceed to each of the two corners of the wing and
secure the anchors approximately 3' diagonally
from the corner. (see anchoring top view)
Repeat for the opposite side wing.
Fig. C Fig. E
3'
3'
3'
Caution, Care & Cleaning
Bungee cords are under extreme tension. Please use caution when applying as they may snap out of your hand and
cause injury. Safety goggles must be worm when securing bungees.
During the first few months of use, it will be necesssary to tighten the cover a few time. Be sure that the cover is kept
tight. Loose fabric will deteriorate quickly. Do NOT apply any “protect & shine” type products to the cover and ends or use
any harsh abrasive cleaners. The cover may be cleaned with mild soap and water.