Shinybow USA SB-3686A User manual

SB-3686A
NTSC/PAL To/From NTSC/PAL DIGITAL VIDEO CONVERTER w/VGA,
HDMI and Composite Video
INSTRUCTION MANUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

CONTENTS
INTRODUCTION .............................................................1
FEATURES & SPECIFICATIONS ....................................2
FRONT PANEL ................................................................3
BACK PANEL ...................................................................5
REMOTE CONTROL .......................................................7
TYPICAL HOOK-UP & OPERATION ................................9
INPUT & OUTPUT RESOLUTIONS ...............................10
INTRODUCTION
The SB-3686A is a high performance video graphics scaler
digital converter supporting (4) different video Input signal types
including 1x Composite Video, 1x Component Video, 1x VGA
and 1x HDMI with 1x HDMI, 1x Composite Video and 1x VGA
Output ports. ALL Output ports are active simultaneously. This
digital converter supports HDMI with 3D comb lter, HDMI 3D
1.3 formats and is HDCP 1.2 Compliant. The SB-3686A auto-
detects the Input video standard in the form of NTSC and PAL
TV systems and converts to High Denition RGB digital HD
signal. The converter supports full HDTV resolution data rates
enabling 480i/p, 576i/p, 720p or 1080i/p-60Hz formats, higher
DVI resolution (1920x1200), HDMI 1080p-60Hz which is ideal for
high denition 3DTVs, HDTVs, Plasma displays or other monitor
applications. Control is provided via front panel buttons with LED
display, RS-232 or wireless IR remote control (included).
PACKAGE CONTENTS
Check that you have the following components;
• SB-3686A Digital Converter
• Operating Instructions
• Master wireless IR Remote Control (SW-3686A)
• Wall mount bracket (Part # 1U-220L)
• Power Supply Input : DC12V, 1.25A, (Worldwide Universal
100~240 VAC, AC 50/60Hz)
1
MultiVideo Digital Converter Series
Thank you for purchasing the SB-3686A Video To HDMI Digital Converter. You will nd this unit easy to install and highly
reliable but it is essential that you read this manual throughly before attempting to use Video To HDMI Digital Converter.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent
© Copyright 2015. All Rights Reserved.
Version 2.1 DEC 2015
3686A-20150502-002
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.

FEATURES
• Multi-Video Input from (4) Video/Comp/VGA/HDMI to (3) Video/VGA/HDMI Digital Converter
• Supports HDMI 1.3 formats (225MB) and suits HDMI V1.3 transmitter & receiver
• Compliant with HDMI 1.3, DVI 2.0, and HDCP 1.2
• Input Supports:
• Analog: Analog, 1x Composite Video, 1x Component Video (YPBPR) and 1x VGA
• Digital: Digital Video/Audio 1x HDMI
• Outputs Supports: 1x Composite Video, 1x VGA (XGA to WUXGA) and 1x HDMI 1080p-60
• Supports High VGA resolution Inputs and Outputs: VGA 640x480, SVGA 800x600, XGA 1024x768, WUXGA 1920x1200 (Max)
• Supports Multi-TV video standard system Inputs and Outputs: NTSC3.58, NTSC-J, PAL, PAL-N, PAL-N Com-n, PAL-M, PAL60
• Maximum Input resolution of 1080i 1920x1080 (only in Component Video)
• (9) Control Buttons Menu/ Mute/ Enter/ Up/ Down/ Right/ Left/ Reset/ Lock
• OSD (on screen display) for menu to control brightness, contrast and saturation
• Provides IR remote control frequency (38KHz)
• Various User Interface Control:
• Front panel push button
• IR wireless remote control
• Power supply DC12Volt, Universal type switch 100~240VAC, 50/60Hz
SPECIFICATIONS
• Type of Converter: (4) In to (3) Out HDMI MultiVideo Converter with Scaler
• Video Input Signal: 1x Composite Video, 1x Component (YPBPR), 1x VGA (RGBHV) and 1x HDMI
• Video Output Signal: 1x Composite Video, 1x VGA (RGBHV) and 1x HDMI
• HDMI/HDCP Support: HDMI 1.3 Receiver & Transmitter (225MB), HDCP 1.2 compliant
• (9) Control Buttons: Menu/ Mute/ Enter/ Up/ Down/ Right/ Left/ Reset/ Lock
• Video Color Subcarrier NTSC/PAL Frequency: NTSC-M (3.58MHz)/ NTSC-J (4.43MHz)/ PAL (4.433619MHz)/ PAL-M
(3.575611MHz)/ PAL-N (3.582056MHZ)/ PAL-60, 0.5 V-pp~2V-pp, 75Ohms
• VGA Resolutions: VGA (640x480), SVGA (800x600), XGA (1024x768), Max WUXGA (1920x1200)
• PAL/NTSC Line Conversion: Composite Video 525/625 Lines
• PAL/NTSC Field Conversion: Composite Video 50/60Hz Fields
• Input Resolution: Component Video input maximum 1080i-60 (1920x1080i)
• Output Scaler: Up to HDMI 1080p-60 and VGA (WUXGA) 1920x1200
• Source Status: Automatic scanning of input/output status
• HDMI Cable Distance: Max. 15M/~49 feet, depending on cable quality
• Infrared Frequency: 38KHz
• Chassis Material: Metal
• Controls: IR remote control or front panel push buttons
• Dimensions: 8.66 x 5.06 x 1.73 in (220x128x44mm)
• Power Supply Spec.: Input 100 ~ 240VAC, 50/60Hz Output DC 12V, 1.25A
• Safety Approvals: CE, FCC, RoHS
• Temperature: 32°F~ 100°F (0~32°C)
• Net Weight (Unit only): 1.4 kgs / 3.09 lb
As product improvements are continuous, specications are subject to change and without notice.
2
FEATURES & SPECIFICATIONS

3
FRONT PANEL
FRONT PANEL
1. POWER LED: The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving
power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last conguration will
be evoked.
2. TV VIDEO SYSTEM SELECT BUTTON: Separate video system outputs 1 thru 4 select LED displays are provided each TV video system
selection. The (4) TV Video system : MTSC-M/N, PAL/NTSC-4.43, PAL-M (60Hz) and PAL-N (comb-n).
3. VGA RESOLUTION SELECT BUTTON: Separate resolution outputs 1 thru 6 select LED displays are provided each VGA resolution selection.
The (6) VGA resolutions : VGA (640x480) SVGA (800x600) XGA (1024x768), SXGA (1280x1024), WXGA (1366x768), WUXGA (1920x1200)
4. HDMI RESOLUTION SELECT BUTTON: Separate resolution outputs 1 thru 4 select LED displays are provided each HDMI resolution selection.
The (4) HDMI resolutions : 480p, 720p, 1080i and 1080p.
5. IR SENSOR: The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
6. INPUT STATUS DISPLAY: Input sources 1 to 4 LED illuminates blue to indicate that a video source is present select.
7. SOURCE SELECT BUTTONS: Separate inputs 1 thru 4 select buttons are provided each source selection.

4
FRONT PANEL
FRONT PANEL
8. LOCK BUTTON:
- Press and hold LOCK button for three seconds lockout the front panel and LED display show out.
- Press and hold LOCK button for three seconds to enable the front panel.
9. MUTE BUTTON:
- Press and hold MUTE button for three seconds the mute the audio and the LED display show out.
- Press and hold MUTE button for three seconds to enable the audio.
10. RESET BUTTON: Press the RESET button to disable the SCN-ADJ screen function.
11. ZOOM BUTTON: Press the ZOOM button to zoom out of the screen when the SCN-ADJ function is enabled.
12. LEFT BUTTON: Press the LEFT button to move left on the screen when the SCN-ADJ function is enabled.
13. RIGHT BUTTON: Press the RIGHT button to move right on the screen when the SCN-ADJ function is enabled.
14. DOWN BUTTON: Press the DOWN button to move down on the screen when the SCN-ADJ function is enabled.
15. UP BUTTON: Press the UP button to move up on the screen when the SCN-ADJ function is enabled.

5
BACK PANEL
BACK PANEL
1. DC POWER INLET / OUTLET: The converter suits a DC power plug-
pack input connector. Please ensure the plug-pack used is of an
approved type and of correct current, voltage output, and connector
polarity. DV 12 Volt, power supply 1.25A.
2. COMPOSITE VIDEO INPUT: Connects a Composite video signal,
using the female RCA connectors, which supports Composite video
to Composite video, VGA or HDMI display devices.
3. COMPONENT VIDEO INPUT: Connects a Component video (YPBPR)
signal directly to the female RCA connectors, which supports
Component video (YPBPR) to Video, VGA or HDTV display devices.
4. VGA: Connects a VGA (RGBHV) signal, using the DB-15F female
connector, which supports VGA (RGBHV) to Video, VGA or HDMI
monitors or display devices.
5. HDMI INPUT: Connects a HDMI signal to the HDMI female
connector, which supports HDMI digital video and audio to HDMI
display.
POWER JACK:
DC Jack - Inner OD Ø 2.1 mm (+)
Outside OD Ø 5.5mm (GND)
Power Input: 12VDC, 1.25A
Composite video via 1x female RCA connector
Component video via 3x female RCA connectors
VGA video jack female HD-15F connector
HDMI digital video and audio female connector

6
BACK PANEL
BACK PANEL
6. VGA OUTPUT: Connects a VGA (RGBHV) signal source to the
VGA connector.
7. HDMI OUTPUT: Connects a HDMI digital video/audio signal link
direct to the female HDMI connector, which supports HDMI digital
video/audio and DVI digital video sources.
8. COMPOSITE VIDEO OUTPUT: Connects a Composite Video signal
output to the connector.
VGA (RGBHV) 1x HD-15P female socket.
Note: With D-SUB-HD15P female socket.
HDMI female connetor
Note: With proper adapters, the scaler can
be used with DVI digital video signals, and
is HDCP compliant.
Composite Video via 1x RCA connector
Note: With 1x female RCA connector.

7
REMOTE CONTROL & REMOTE PROTOCOL COMMANDS
Before making any connections observe the following:
• Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• To yield video/audio to an output, select the input source by using the front panel input buttons, the supplied IR remote control, or
through the RS-232 serial communication port.
• Upon power up the switcher will return to its last used setting before Powered down.
REMOTE CONTROL
IR REMOTE CONTROL KEY :
1. / 2. POWER ON AND OFF: Turn on or off the scaler
3. Source-1 Select Composite Video / stereo audio signal.
4. Source-2 Select Component Video / stereo audio signal.
5. Source-3 Select VGA / stereo audio signal.
6. Source-4 Select HDMI signal.
7. / 8. / 9. / 10. ARROW KEYS: Move up, down, left or right between the OSD options. Use
left and right keys to adjust the value of a parameter. Use down key to enter the next
layer of options and up key to move back.
11. ENTER: Conrm your selection/enter the next layer of OSD options
12. / 13. / 14. OUTPUT (HDMI, VGA, TV SYSTEM): Select the desired output resolution
supported by your display device
15. ZOOM: Open SCN-ADJ zoom out function.
16. RESET : Open SCN-ADJ to RESET SCN-ADJ conguration.
17. LOCK:
- Press and hold LOCK button for three seconds lockout the front panel.
- Press and hold LOCK button for three seconds to enable the front panel.

8
IR DATA CODE LIST
IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
HOW TO SETUP IR CODES : CUSTOM CODE : 53AC
POWER ON: 53AC A15E
POWER OFF: 53AC A25D
VIDEO SOURCE :
VIDEO 53AC BB44
S-VIDEO 53AC 916E
SCN-ADJ.:
ENTER 53AC AB54
UP 53AC A758
RIGHT 53AC AA55
LEFT 53AC A956
DOWN 53AC A857
RESOLUTIONS:
HDMI 53AC 956A
VGA 53AC 936C
TV SYSTEM 53AC 10EF
SCN-ADJ.:
ZOOM 53AC AF50
RESET 53AC 9B64
LOCK 53AC B54A
ExAMPLE 1: SELECT INPUT VGA AND OUTPUT HDMI
THE IR DATA CODE: 53AC 0AF5 53AC 07F8
ExAMPLE 2: VIDEO -> MOVE RIGHT -> MOVE DOWN TO NEXT LAYER -> ENTER TO CONFIRM SELECTION
THE IR DATA CODE: 53AC BB44 53AC AA55 53AC AB54

INSTALLING DIAGRAM
Sample Connection:
1. Using a IR remote to control the Switch-Converter (SB-3686A).
2. Input source supports: Composite video, S-Video(Y/C), VGA (RGBHV) and HDMI total (4) source devices.
3. Output Supports: NTSC/PAL TV, VGA Monitor or HDMI displays.
NOTE:
1. Output TV Support :
- NTSC/PAL TV
- VGA Monitor
- HDMI HDTV
2. Control Switch via a IR Remote.
Application IR and Front Panel to control the Switcher.
9
TYPICAL APPLICATION

VIDEO INPUT & VIDEO-VGA-HDMI RESOLUTION
Resolutions available
Composite Video/Audio Input Resolutions: NTSC @3.58/60Hz
NTSC @4.43/50Hz
PAL @4.43/50Hz
PAL-M @3.57/60Hz
PAL-N @3.57/50Hz
Composite Video/Audio Output Resolutions: VIDEO (Composite Video):
NTSC
PAL
PAL-M 60Hz
PAL-Nc
VGA:
VGA (640x480)
SVGA (800x600)
XGA (1024x768)
SXGA (1280x1024)
WXGA (1366x768)
WUXGA (1920x1200)
HDMI:
480p
720p
1080i
1080p
PS: TV SYSTEM : 1. NTSC:M/N, 2. PAL: BDGHIN/NTSC-4.43Hz, 3. PAL-M:@60Hz, 4. PAL-Nc : COMB-N
COMPONENT VIDEO INPUT & VIDEO-VGA-HDMI RESOLUTION
Resolutions available
Component Video/Audio Input Resolutions: 480p
576p
720p @50Hz
720p@60Hz
1080i@50Hz
1080i@60Hz
Component Video/Audio Output Resolutions: VIDEO (Composite Video):
NTSC
PAL
PAL-M 60Hz
PAL-Nc
VGA:
VGA (640x480)
SVGA (800x600)
XGA (1024x768)
SXGA (1280x1024)
WXGA (1366x768)
WUXGA (1920x1200)
HDMI:
480p
720p
1080i
1080p
PS: TV SYSTEM : 1. NTSC:M/N, 2. PAL: BDGHIN/NTSC-4.43Hz, 3. PAL-M:@60Hz, 4. PAL-Nc : COMB-N
VGA INPUT & VIDEO-VGA-HDMI RESOLUTION
Resolutions available
VGA Video/Audio Input Resolutions: SVGA (800x600)
XGA (1024x768)
XGA (1152x864)
HD720 (1280x768)
WXGA (1280x768)
WXGA (1280x800)
SXGA (1280x960)
SXGA (1280x1024)
SXGA (1360x768)
VGA Video/Audio Output Resolutions: VIDEO (Composite Video):
NTSC
PAL
PAL-M 60Hz
PAL-Nc
VGA:
VGA (640x480)
SVGA (800x600)
XGA (1024x768)
SXGA (1280x1024)
WXGA (1366x768)
WUXGA (1920x1200)
HDMI:
480p
720p
1080i
1080p
PS: TV SYSTEM : 1. NTSC:M/N, 2. PAL: BDGHIN/NTSC-4.43Hz, 3. PAL-M:@60Hz, 4. PAL-Nc : COMB-N
10
INPUT & OUTPUT RESOLUTION TABLES

HDMI INPUT & VIDEO-VGA-HDMI RESOLUTION
Resolutions available
HDMI Video/Audio Input Resolutions: 480p/480i 720x480p@60Hz
480p/480i 1280x720p@60Hz
480p/480i 1920x1080p@60Hz
576p 720x480p@60Hz
576p 1280x720p@60Hz
720p 720x480p@60Hz
720p 1280x720p@60Hz
1080i 1920x1080p@60Hz
1080p 720x480p@60Hz
1008p 1280x720p@60Hz
1080p 1920x1080p@60Hz
2160p 720x480p@60Hz
2160p 1280x720p@60Hz
2160p 1920x1080p@60Hz
HDMI Video/Audio Output Resolutions: VIDEO (Composite Video):
NTSC
PAL
PAL-M 60Hz
PAL-Nc
VGA:
VGA (640x480)
SVGA (800x600)
XGA (1024x768)
SXGA (1280x1024)
WXGA (1366x768)
WUXGA (1920x1200)
HDMI:
480p
720p
1080i
1080p
PS: TV SYSTEM : 1. NTSC:M/N, 2. PAL: BDGHIN/NTSC-4.43Hz, 3. PAL-M:@60Hz, 4. PAL-Nc : COMB-N
HDMI (PC) Video/Audio Input
Resolutions:
640x480@60 Hz
800x600@60Hz
1024x768@60Hz
1280x1024@60Hz
1920x1080@60Hz
HDMI (PC) Video/Audio Output
Resolutions:
VIDEO (Composite Video):
NTSC
PAL
PAL-M 60Hz
PAL-Nc
VGA:
VGA (640x480)
SVGA (800x600)
XGA (1024x768)
SXGA (1280x1024)
WXGA (1366x768)
WUXGA (1920x1200)
HDMI:
480p
720p
1080i
1080p
11
INPUT & OUTPUT RESOLUTION TABLES

12
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its ofces within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKEANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS,ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT

THIS PAGE IS INTENTIONALLY LEFT BLANK.

122 Rose Ln. Suite 303 | Frisco, Texas 75034
1-877-SHINY-USA
1-877-744-6987
1-972-377-2508
[email protected]
www.shinybowusa.com