Shinybow USA SB-5658p User manual

MULTIMEDIA AUDIO AND VISUAL
1x8 HDMI DISTRIBUTION AMPLIFIER
INSTRUCTION MANUAL
MODEL : SB-5658p
1x8 HDMI DISTRIBUTION AMPLIFIER
HDMI DISTRIBUTION AMPLIFIER Series
Thank you for purchasing the SB-5658p 1x8 HDMI DISTRIBUTION AMPLIFIER. You will find this unit easy to
install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this
distribution amplifier.

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

INTRODUCTION
INTRODUCTION
The SB-5658p is high quality HDMI distribution amplifier, HD high performance designed to distribution HDMI signal. Providing I/O as following:
1x input : 1x HDMI (Digital Video-TMDS and Audio)
8x outputs : 8x HDMI (Digital Video-TMDS and Audio)
Automatic input/output HD signals detection:
PC monitor from VGA to UXGA
HDMI 480i To 1080p
DVI 480i To 1080p
The distributor support data rates up to 2.25 Gbps. And enable 1080p HDMI formats and UXGA DVI resolution (1920x1200) to LCD and
Plasma display applications. Auto scan function software is built-in to extend HDMI signal for long distance. This product is certified as
being fully HDMI and HDCP compliant. This product is also RoHS, CE, FCC compliant. Support high HDMI (HDCP) source to multiple
HDMI (HDCP) displays, LCD monitors or HD projectors.
Supplied Accessories
(1) 1 Instruction Manual
(2) 1 SB-5658p Distribution Amplifier
(3) IR Remote control
(4) 19 inch (1 RU) rack mount brackets
(5) RS-232 Software (All Windows Operating Systems)
(6) 1 Power Supply 12VDC, Universal Type 50/60Hz, 100-230 VAC
Safety Notice!
To prevent damage to your television equipment use only the supplied
AC Adaptor and make the power connections to your television
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
This symbol is intended to alert the user to the presence of non-insulated
“dangerous voltage” within the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operational
and maintenance (serving) instructions in the literature accompanying the
appliance.
To prevent electric shock do not use this (polarized) plug with an extension cord,
receptacle or other outlet unless the blades can be fully inserted to prevent blade
exposure. To prevent electric shock, match wide blade of plug to wide slot, fully
insert.
3
TABLE OF CONTENTS ...........................................3
INTRODUCTION ....................................................3
FEATURES&SPECIFICATIONS..................................4
FRONT PANEL.......................................................5
REAR PANEL.........................................................6
REMOTE CONTROL...............................................7
TYPICAL APPLICATION...........................................8
LIMITED WARRANTY...............................................9
Input: 1x HDMI
Output: 8x HDMI
Power Input: DC+12V, @1.25A

FEATURES & SPECIFICATIONS
FEATURES
• Support 1x8 HDMI Distribution Amplifier
• I/O Signals : HDMI with HDCP Digital Video and Digital Audio (PCM)
• HDMI and HDCP compliant
• Support link speeds of up to 2.25 Gbps (link clock rate of 225 MHZ)
• Support wide range of PC resolutions from XGA to UXGA 1600x1200 and HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i
& 1080p
• Compatible with all HDMI devices, PC monitors, Plasma TV display and HDTV
• Support Digital Video TMDS formats in Deep Color 12bits
• Support colour depth of up to 36 bits and ensures robust transmission of high-quality uncompressed video content, along with state-
of-the-art uncompressed and set top boxes.
• Bi-direction colour space conversion(SCS) between RGB and YCBCR color spaces with programmable coefficients.
• Auto-Scan input and outputs status via LED display on front panel
• Control by Selection buttons on front panel and use IR Remote Controller
• Support desktop with Ear mount and 19 inch Rack mountable type panel
• Power supply DC12Volt, Universal Type switch 100~230VAC, 50/60Hz
SPECIFICATIONS
• Type of Distributor: 1x8 HDMI Distribution Amplifier
• Signal Supports: HDMI Standard, DVI and HDCP Compliant
• Video Supported: 1080p HDMI formats 1920x1200 and DVI UXGA HD resolutions
• Audio Supported: DTS-HD Master Audio, Dolby True -HD & Dolby Digital Plus
• Type of Signal: TMDS Digital Video PCM Digital Audio
• Compliant with HDMI standard: HDMI and HDCP
• HDTV Support: 1080p HDMI formats and UXGA 1600x1200 resolution
• Controls: IR Remote and IR Extender (Distance Maximum 1000 ft (300M))
• Data Rates: 250Mbps to 2.25 Gbps
• Pixel clocks: 250Mbps to 2.25 Gbps. Pixel clocks: 25M Hz to 225 MHz
• HDMI Cable Distance: 30ft (10 M) at 2.25Gbps
• Various video input interface supporting digital video standards such as:
• RGB/YCBCR : 24/30/36-bits
• YCBCR : 8/10/12/16/20/24-bits
• Double data rate interface for RGB/YCBCR : 12/15/18-bits
• Infrared frequency: 38KHz
• Regulatory Approvals: CE, FCC, RoHS (2002/95/EC)
• Dimensions (WxDxH): 19 x 7.87 x 1.75 in (482mm x 200mm x 44mm)
• Net Weight (Unit Only): 4.08 lbs / 2.45 Kgs
• Power Supply: DC12V/1A~2A (Full load Consumption Maximum 1.25A)
As product improvements are continuous, specifications are subject to change without notice.
4

5
FRONT PANEL
FRONT PANEL
1 POWER SWITCH
The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power
2SOURCE DEVICE STATUS DISPLAY
Source 1 to LED illuminates blue to indicate that a video source is present on that input.
3SOURCE DEVICE STATUS DISPLAY
Channel 1-8 show by LED display.
4 IR SENSOR
The IR sensor receives IR commands from the supplied remote controller.
5 19 INCH EAR MOUNT PAIR
19 inch (1 RU) rack mount brackets
CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal input-output, Power requirements plus any controls present.
Before using the distributor, please take the time to make certain that the device you wish to connect to its inputs is functioning properly
in all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device.
If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s) of the distributor to the
carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor, connect the DC connector to the distributor first and
then plug the adaptor into a functional AC outlet.

6
REAR PANEL
REAR PANEL
1 DC POWER INLET
The distributor is fitted with a DC power plug-park input connector.
Please ensure that the plug-park used is of an approved type and
is of sufficient current carrying capacity with the correct voltage
and connector polarity. 12Volt DC power supply 2A Max.
2IR EXTENDER CONTROL
Support one of IR Extender. Extend distance maximum 1000 ft
4INPUT - 1x HDMI
Connect a signal link of HDMI direct digital video/audio to
this Female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources.
Input 1 - HDMI Digital Video/Audio, Connector with fix screw
3OUTPUTS - 1,2,3,4,5,6,7,8 HDMI
5 Connect a signal link of HDMI direct digital video/audio to
this Female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources.
Output 1 - HDMI Digital Video/Audio, Connector with fix screw
Output 2 - HDMI Digital Video/Audio, Connector with fix screw
Output 3 - HDMI Digital Video/Audio, Connector with fix screw
Output 4 - HDMI Digital Video/Audio, Connector with fix screw
Output 5 - HDMI Digital Video/Audio, Connector with fix screw
Output 6 - HDMI Digital Video/Audio, Connector with fix screw
Output 7 - HDMI Digital Video/Audio, Connector with fix screw
Output 8 - HDMI Digital Video/Audio, Connector with fix screw
Power Jack:
DC Jack - Inner OD ᴓ2.1mm (+ )
Outside OD ᴓ5.5mm (GND)
Power input - 12VDC, 2A
IR Extender Jack:
Female Jack - inner OD (/) 3.5 mm
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals
HDCP compliant. DVI does not support audio.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals
HDCP compliant.

REMOTE CONTROL
Before making any connections to the SB-5658p. Observe the following:
> Ensure the mains voltage supply matches the label on the
supplied plug- Pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a
common point.
> Avoid powering equipment within a system from multiple
power sources that may be separated by large distances
> Connect all audio video sources and destination equipment
> Power up all source and destination audio-visual sources
> For each destination output select the appropriate input source
by using the front panel input 1~8 select buttons. The
supplied IR remote control. Or through the RS-232 serial
communications port.
> Upon power up the switcher will return to its last used setting
before Powered down.
REMOTE CONTROL
1. & 2. SWITCH POWER ON or OFF:
Controller with a power ON and OFF
CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal input-output, Power requirements plus any controls present.
Before using the switcher, please take the time to make certain that the device you wish to connect to its inputs is functioning properly in
all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device.
If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s) of the switcher to the
carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor, connect the DC connector to the switcher first and then
plug the adaptor into a functional AC outlet.
7

TYPICAL APPLICATION
SHINYBOW SB-5658p
1x HDMI source to 8 x HDMI displays Distribution Amplifier
INSTALLING
CONTROL PORTS:
1. IR EXTENDER - IR Extend with distance 1000 ft (300M) Maximum
INPUT PORT SIGNAL :
1. HDMI - HDMI connector with fix screw
OUTPUTS PORT SIGNALS:
1. HDMI - HDMI connector with fix screw
2. HDMI - HDMI connector with fix screw
3. HDMI - HDMI connector with fix screw
4. HDMI - HDMI connector with fix screw
5. HDMI - HDMI connector with fix screw
6. HDMI - HDMI connector with fix screw
7. HDMI - HDMI connector with fix screw
8. HDMI - HDMI connector with fix screw
SB-5658p SUPPORTS ONE HDMI INPUT TO EIGHT HDMI DISTRIBUTOR OUTPUTS
SUPPORT IR & IR EXTENDER PORT
8

TYPICAL APPLICATION
REAR PANEL IR EXTENDER PORT
IR EXTENDER PACKAGE:
HOW TO SETUP THE IR EXTENDER COMPONENTS
9

10
LIMITED WARRANTY
SHINYBOW WARRANTY
SHINYBOW Technology warrants this product against defects in materials and workman ship for a period of 3 years from the date of purchase. Please be sure to send
in your warranty registration card promptly, as the warranty will not be active without registration.
Should this product, in SHINYBOW Technology’s opinion, after inspection, prove defective within this warranty period, SHINYBOW Technology, at its option, will repair
or replace this product without charge, to whatever extent it shall deem necessary to restore said product to proper operation condition. This does not extend the
warranty period.
This warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, and abnormal operating conditions or
non-SHINYBOW Technology authorized modification to the product.
If repairs are necessary under the warranty policy, the original purchaser must return the product to local distributor, freight prepaid. After repairs are complete, the
product will be returned.
REGULATORY COMPLIANCE
The product complies with the relevant standards for CE, FCC and RoHS approval.
The powerAdaptor/Supply has been tested for compliance with UL.CSAand CE standards.
TROUBLESHOOTING
If you experience a <no signal> with this switcher or distributor outputs, first make certain that there is a signal being fed to its inputs from the connected device is
acceptable.
Disconnect the cables from the switcher or distributor inputs and connect them directly to an appropriate monitoring device. If you do not see or hear a signal the
problemmay well behe signal source itself.Also check thattheACoutlet you have used topower the switcheror distributor isactually providing poweras a wallswitch
often controls anAC outlet.
Verify that there is power to the device. If the unit is receiving power, the power on indicator light in the power switch should be glowing.
The second most common problem with the switcher or distributor revolves around the cables, Inspect the cables for loose connectors or cable damage such as
crushed cable or cables with cuts or nicks. Replace any cable exhibiting these problems.
We recommend using the highest quality cables so that you can achieve the best results. Poor quality cables provide will poor quality signals.
DISCLAIMER OF WARRANTIES AND LIABILITY
Neither Shinybow nor its suppliers or licensors makes any warranty whatsoever, including without limitation, that any defects will be corrected; including the accuracy,
completeness,reliability,availability,suitability,quality,non-infringement,operationorresultobtainedfromtheuseofanycontent,productorserviceprovidedaccessible
from or distributed through Shinybow.
ALL CONTENT, PRODUCTSAND SERVICES INCLUDED IN OR ACCESSIBLE ARE PROVIDED “AS IS”AND WITHOUT WARRANTIES OR REPRESENTATIONS
OF ANY KIND (EXPRESS, IMPLIEDAND STATUTORY, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF TITLE AND NON-INFRINGEMENTAND THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE), ALL OF WHICH SHINYBOW DISCLAIMS TO THE FULLEST
EXTENT PERMITTED BYLAW.YOUR USE OF THE CONTENT, PRODUCTSAND SERVICES ISATYOUR SOLE RISK.
To the extent permitted under applicable law, no responsibility is assumed for any injury and/or damage to persons, animals or property as a matter of products liability,
negligence or otherwise, or from any use or operation of any ideas, instructions, methods, products or procedures contained.
TOTHEEXTENTPERMITTEDUNDERAPPLICABLELAW,INNOEVENTSHALLSHINYBOWORITSSUPPLIERSORLICENSORSBELIABLEFORANYDAMAGES
(INCLUDING,WITHOUTLIMITATION,CONSEQUENTIAL,SPECIAL,INCIDENTAL,INDIRECT,ORSIMILARDAMAGES,PERSONALINJURY(INCLUDINGDEATH),
LOSS OF PROFITS, CORRUPTION OR LOSS OF DATA, BUSINESS INTERRUPTION OR ANY OTHER COMMERCIAL DAMAGES OR LOSSES) ARISING OUT
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF CONTENT, PRODUCTS OR SERVICES, OR SHALL THE LIABILITY OF SHINYBOW OR
ITS SUPPLIERS AND LICENSORS EXCEED A SUM EQUAL TO THE FEES PAID BY YOU HEREUNDER, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Shinybow does not claim ownership, endorse or take responsibility for any third-party products, information, guidelines, materials or services that may be offered,
advertised, provided or incorporated in the content, products or services.
INDEMNIFICATION
You hereby agree to indemnify and hold Shinybow, its directors, officers, shareholders, predecessors, successors in interest, employees, agents, suppliers and
licensorsharmlessfromandagainstanyand all third-partyclaimsofliability,losses,damagesandcosts,including,without limitation,reasonableattorneys’fees,arising
out of or in connection with your use of or inability to use the content, products or services.

1399 Wildfire Lane | Frisco, TX 75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 [email protected]
MULTIMEDIA AUDIO AND VISUAL
www.shinybowusa.com