SHO-ME 09.201LED User manual

MODEL NO. 09.201LED
Rechargeable Light W/Wall-Mount Charger
INSTRUCTIONS
07-29-10
SHO-ME®
Before using, place light in charger so the contacts on the light will match up with the contacts on the
charger. When the green LED light is glowing, the battery is fully charged. If the red light is glowing, the
battery is being charged. (Red and green LED lights are located on the rechargeable light on the left-hand
side of the handle.).
10% 30% 50% 70% 90% 110%
PERCENT OF DISCHARGE
0
200
400
600
800
1000
1200
1400
NUMBER
OF
CYCLES
NOTE: The battery used in your new SHO-ME rechargeable light is lead-acid battery. This is not a
memory type battery and DOES NOT require being fully discharged. The battery can be recharged
hundreds of times, depending on the depth of discharge. For prolonged battery life, always
keep your rechargeable light in the charger and avoid running the light till the battery
is completely dead.
Number of discharge cycles at various depths of discharge to reach 60% of original life.
PERCENT OF
CAPACITY
100%
90%
80%
110%
70%
60%
50%
40%
30%
20%
10%
HOURS ON CHARGE
012345678910 11 12
0%
RETURNED
Your new SHO-ME rechargeable light is protected by a charging regulator, therefore it cannot
be overcharged. When not in use, leave light in the charger so it will always be charged.
The SHO-ME rechargeable light should be mounted and charged with the bulb pointed up
Your new SHO-ME LED Rechargeable has both "Flood" and "Spot" capabilities. By moving the two way
toggle switch to the right you activate the High Intensity 5 Watt LED for the Spot Function. This function is
used for shining long distances. When the two way switch is moved to the left the "Flood" function is
activated. This function is for working in a close area, when you need to light up a wide area.
The "Flood" function will run for an estimated time of 50 hrs, before requiring a recharge. The "Spot"
function will run for an estimated time of 5 hrs before needing to be recharged. Although your NEW LED
Rechargeable is capable of going for long periods of time without being recharged, it is recommended that
you leave it on the charger when not in use.
®
®
®
®

07-29-10
SHO-ME®
Installation Instructions for the Wall-Mounted
AC & DC Rechargeable Lights
Mount the charger-base in an
upright position (as in illustration)
near a 110-volt receptacle. Plug the
AC charger into the receptacle. Red
light indicates the battery is
charging.
Mount the charger-base in a vehicle
in an upright position (as in
illustration) near the cigarette lighter
or other accessory outlet and plug
the DC charger into the receptacle.
Mount the charger-base in a
vehicle in an upright position (as
in illustration). Connect the Black
wire to ground and the Red wire
to a constant +12-volt positive.
DC ChargerAC Charger Direct-Wire DC Charger
Mount With
This Side
UP
Placing light on charging base
Hold light firmly in hand. Place left side
of the light in the charging base then
rotate light to the right until it latches
into place.
Removing light from charging base
Hold light firmly in hand. Press out on
the locking tab on the charging base
then pull light from charging base or
pull up on light to slide light from
charging base.
PRODUCTS COMPANY 804 East Hwy 248 Cassville, MO 65625
U.S. and Canada Toll Free Numbers Phone: [phone] FAX: [phone]
E-mail: [email protected] WEB: www.able2products.com
CHARGING
FULL CHG
SHO-ME
®
Turning the Night Eye LED lights On &Off
Simply press the on/off button one time. This
will turn the LED lights on in either a steady or
flashing mode. To go to the other mode,
simply turn the light off and turn it on again.
Each time the LED lights are turned on, they
will change modes.
Switch for
Night Eye
LED Lights
Night Eye
LED Lights
For Model No
09.201LEDTL & 09.201LEDTL