SHO-ME 30.2109 User manual

P.O. Box 543 • 804 E. Hwy 248 Cassville, MO 65625-0543
Local and International Numbers
Phone: [phone] Fax: [phone]
U.S. and Canada Toll-Free Numbers
Phone: [phone] Fax: [phone]
Installation Manual
SHO-ME®
ELECTRONIC SIREN
Model 30.2109
ManufacturedintheU.S.A
Other quality products manufactured by SHO-ME®
Speakers; LED Lights; Strobe Lights (Directional and 360º);
Headlight Flasher Kits; Full size LED Light Bars;Mini LED Light Bars;
Mini-Bars; Custom Switch Panels; Spot and Flood Lights;
6VoltRechargeableLights;Map Lights; Megaphones;
Accessory Outlets; Bucket Lights
andmany moreComponentsandAccessories.
WIRING DIAGRAM

ELECTRONIC SIREN
MODEL 30.2109
INTRODUCTION
The30.2109 sirenconsists ofan amplifierwhich powers
one 100 watt RMS speaker. The amplifier, because of its small
physical size, mounts conveniently in a remote position from the
function control switch.
The30.2109 sirensystemincludes onecenter-off rocker
switchesthat allowsthe operator toselect theWAILorYELP
functions. Themomentaryswitch allowstheoperator tosoundthe
AIRHORN.
INSTALLATION OF POWER AMPLIFIER
Select a location suitable for installation of the amplifier.
Thisarea mustbe free from moisture, heat, and abuse. DO NOT
MOUNT IN THE ENGINE COMPARTMENT. Using the amplifier
asa template,mark the locationof themounting holes. Drillholes
atthese locationsto assistinstarting themounting screws
provided. Allinstallationsare thesole responsibility ofthe buyer.
CONTROL SWITCH
Select a location suitable for installation of the control
switch. The area selected should provide ease of operation and
must not interfere with normal operation of the vehicle or
deployment of air bag. Using the switch bracket as a template,
mark the location of the mounting holes. Drill holes at these
locations to assist in starting the mounting screws provided.
SPEAKER CONNECTIONS
Use only one 100 watt speaker with an 11 ohm
impedance. Connect one conductor of the 16-2 wire supplied to
the terminal on the siren marked “SPKR COMMON”. Connect
the second conductor of the 16-2 wire to the “100 WATT”
terminal on the siren.
POWER INPUT CONNECTIONS
Connectthe suppliedblack wireto the terminalon thesiren
marked“GROUND”. Connect theother endofthe blackwire to
ground. Thenegative terminalof the batteryis apreferable
location. Connectthe suppliedred wireto the terminalon the
sirenmarked “+12 VOLTS”. Thisterminalon thesiren connects
directlyto theon board20 ampfuse. Connect theother endof the
red wire to a positive source. To protect the wiring going to the
siren,install anin-line fuseor circuit breakeron theend ofthe wire
asclose tothe positive source as possible. Thecurrent drawof
thesiren duringoperation isapproximately15 amps,when
suppliedby 13.8volts. Thecurrent drawof the sirenwhen power
isapplied, butno functionsare selected,is approximately.03
amps.
CONTROL SWITCH CONNECTIONS
Connect the wires from the control switch to the terminals
on the siren as shown in the diagram. By applying +12 volts to
one of the terminals, the corresponding sound will be produced.
Connect the green wire from the switch to the terminal on the
sirenmarked “WAIL”. Connect thebrown wirefrom the switchto
theterminal on thesiren marked “HORN”. Connectthe yellow wire
fromthe switchtothe terminalon thesiren marked “YELP”. Run
redwire fromterminal marked“+12 VOLTS Input”to power
source. ConnectWhite wirefrom switchpanel to terminalmarked
“+12VOLTSto switches”.
WARRANTY
Merchandise returned under warranty shall be subject to
factory inspection and repaired, replaced, or credited at Able 2
Products Company, Inc.’s option. Water, condensation, or
negligence will VOID warranty. This unit’s warranty period is for
2 years parts and labor.