Shop fox W1768 User manual

OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 5/07)
MODEL W1768/W1769
1 HP POWER FEEDER
WITH 4 ROLLERS
Phone: [phone] • Online Technical Support: [email protected]
COPYRIGHT © SEPTEMBER, 2007 BY WOODSTOCK INTERNATIONAL, INC. REVISED FEBRUARY, 2014 (BL)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9857CR Printed in Taiwan

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

SET UPELECTRICAL MAINTENANCE SERVICE PARTS
OPERATIONS
SAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Contents
INTRODUCTION ..................................................................................................2
Woodstock Technical Support ............................................................................ 2
Machine Specifications .................................................................................... 3
SAFETY ............................................................................................................6
Standard Machinery Safety Instructions ................................................................ 6
Additional Safety for Power Feeders.................................................................... 8
ELECTRICAL ......................................................................................................9
Circuit Requirements ...................................................................................... 9
Grounding Requirements................................................................................ 10
Extension Cords .......................................................................................... 10
SETUP ........................................................................................................... 11
Unpacking ................................................................................................. 11
Inventory .................................................................................................. 11
Cleaning Machine......................................................................................... 12
Assembly................................................................................................... 13
Base Mounting ............................................................................................ 14
Test Run.................................................................................................... 16
OPERATIONS ................................................................................................... 17
General .................................................................................................... 17
Changing Feed Speed.................................................................................... 18
Power Feeder Accessories .............................................................................. 19
MAINTENANCE ................................................................................................. 21
General .................................................................................................... 21
Cleaning ................................................................................................... 21
Lubrication ................................................................................................ 21
SERVICE ......................................................................................................... 22
General .................................................................................................... 22
Wheel Replacement ..................................................................................... 22
Troubleshooting........................................................................................... 23
Electrical Safety Instructions........................................................................... 24
Model W1768 Wiring Diagram .......................................................................... 25
Model W1769 Wiring Diagram .......................................................................... 26
PARTS ........................................................................................................... 27
Main Breakdown .......................................................................................... 27
Stand Breakdown......................................................................................... 29
Labels & Cosmetics ...................................................................................... 30
WARRANTY ..................................................................................................... 33

-2-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
INTRODUCTION
Woodstock Technical Support
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
In the event that questions arise about your machine, please contact Woodstock International Technical
Support at [phone] or send e-mail to: [e-mail]. Our knowledgeable staff will
help you troubleshoot problems or process warranty claims.
INTRODUCTION
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [e-mail]

-3-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
INTRODUCTION
MODEL W1768/W1769
1 HP POWER FEEDER WITH 4 ROLLERS
Model Number W1768 W1769
Overall Dimensions
Weight 144 lbs.
Length/Width/Height 43–1/4 x 23–1/2 x 29–1/2 in.
Column Diameter 2–1/4 in.
Shipping Dimensions
Carton 1
Type Cardboard
Content Machine
Weight 75 lbs.
Length/Width/Height 30 x 12 x 22 in.
Carton 2
Type Cardboard
Content Stand
Weight 79 lbs.
Length/Width/Height 30 x 13 x 11 in.
Electrical
Power Requirement 220V, Single-Phase, 60 Hz 220V, Three-Phase, 60 Hz
Minimum Circuit Size 15A
Switch Forward/Reverse
Switch Voltage 220V
Cord Length 9 ft.
Cord Gauge 16 AWG
Plug Included No
Recommended Plug Type NEMA 6-15 NEMA 15-15
Main Motor
Type TEFC Capacitor Start Induction
Horsepower 1 HP
Voltage 220V
Phase 1-Phase 3-Phase
Amps 4.2A/2.5A 3.4/2.5A
Speed 3450/1725 RPM
Cycle 60 Hz
Power Transfer Gear/Chain
Bearings Lubricated for Life
Machine Data Sheet
© Woodstock International, Inc. • Phone #: [phone] • Web: www.shopfox.biz
MACHINE
SPECIFICATIONS

-4-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
INTRODUCTION
Model Number W1768 W1769
Operation Information
Minimum Workpiece Length 7 in.
Number of Feed Speeds 4
Feed Speeds 13, 26, 33, 66 FPM
Swing 360 deg.
Vertical Movement 9-7/8 in.
Horizontal Movement 18-1/8 in.
Rotation Forward, Reverse
Roller Information
Number of Rollers 4
Roller Width 2-3/8 in.
Roller Diameter 4-3/4 in.
Roller Suspension Travel 3/4 in.
Maximum Height of Rollers 8-1/8 in.
Distance Between Rollers 5 in.
Construction
Roller Synthetic Rubber
Housing Cast Aluminum
Supports Cast Iron
Column Steel
Paint Epoxy
Other
ISO Factory ISO 9001
Country of Origin Taiwan
Warranty 2 Years
Assembly Time 45 Minutes

-5-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
INTRODUCTION
Controls and Features
Horizontal
Handwheel
Vertical Travel
Handcrank
Horizontal
Travel Lock
Figure 1. Controls and Features.
1 HP 2-Speed
Motor
Rotary
Movement
Lock
Vertical
Travel
Lock
Lower Elbow
Joint Lock
Gearbox Oil
Plug
Upper Elbow
Joint Lock
Power Feeder
Swivel Lock

-6-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SAFETY
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.
NOTICE
SAFETY
OWNER’S MANUAL.
Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY.
Untrained operators
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
DANGEROUS ENVIRONMENTS.
Do not use
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
MENTAL ALERTNESS REQUIRED.
Full mental
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
ELECTRICAL EQUIPMENT INJURY RISKS. You can
be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
Standard Machinery Safety Instructions
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-
sures—this responsibility is ultimately up to the operator!
SAFETY
Standard Machinery Safety Instructions

-7-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SAFETY
WEARING PROPER APPAREL. Do not wear
clothing, apparel,or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.
HAZARDOUS
DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
HEARING PROTECTION.
Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
REMOVE ADJUSTING TOOLS.
Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!
INTENDED USAGE.
Only use machine for its
intended purpose—never make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leadsto serious
personal injury or death!
AWKWARD POSITIONS.
Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
CHILDREN & BYSTANDERS.
Keep children and
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.
GUARDS & COVERS.
Guards and covers reduce
accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury may
occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during
operation greatly increases risk of injury or
loss of control. Before starting, verify machine
is stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.
UNATTENDED OPERATION. To reduce the risk
of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could
malfunction, leading to serious personal injury
or death.
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away
from heated surfaces, high traffic areas, harsh
chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the
intended operation, stop using the machine!
Contact Technical Support at [phone].

-8-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SAFETY
Additional Safety for Power Feeders
ATTACHED MACHINERY.
Follow all warnings and
safety information for the attached machine
doing the cutting work.
HAND SAFETY
. Keep hands away from rotating
parts on power feeder and spinning blade
or cutter of associated machine. Turn power
feeder and associated machine OFF and only
use a brush or compressed air to remove
sawdust.
INSTALLING GUARDS.
Install guards, fences, and
hold-downs before starting attached machine
or power feeder. Repair or replace guards
promptly if they become damaged.
KICKBACK.
Occurs when workpiece is ejected
from machine with great force, striking
operator or bystanders. Commonly caused by
improper machine or power feeder setup.
VERIFY EACH SETUP.
Ensure that power feeder
is set up correctly and firmly secured before
feeding workpiece. An improperly adjusted
power feeder could increase the risk of
kickback, because it will continue feeding
when stock is not properly positioned for the
cut.
FEATHERBOARD. When cutting long or large
stock that is difficult to feed properly, use
a featherboard before powerfeeder (on the
infeed side) to maintain even pressure and
control of workpiece against fence, and help
reduce risk of kickback.
FEED WORKPIECE PROPERLY. Verify blade or
cutter of associated machine is at full speed
before feeding stock with power feeder.
Do not feed workpiece too quickly. Verify
power feeder wheels are slightly lower than
workpiece. Stop power feeder before stopping
cutting tool.
WORKPIECE SUPPORT. Support workpiece
continuously during operation as required. Use
auxiliary stands or support tables for long or
wide stock.
ADJUSTMENTS/MAINTENANCE. Make sure power
feeder is turned OFF, disconnected from
power, and all moving parts are completely
stopped before doing adjustments or
maintenance.
MAIN INJURY HAZARDS: Death, amputation, or crushing injuries from getting entangled in
moving parts—which may include being pulled into the cutting tool on attached machinery;
death, blindness, broken bones, or bruises from being struck by an ejected workpiece
(kickback). To minimize your risk of these hazards, always heed the following information:
READ and understand this
entire manual before using
this machine. Serious per-
sonal injury may occur
if safety and operational
information is not under-
stood and followed. DO
NOT risk your safety by
not reading!
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.

-9-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
ELECTRICAL
ELECTRICAL
Circuit Requirements
This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the full-
load current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
W1768 Circuit Requirements
This machine is prewired to operate on a 220V power
supply circuit that has a verified ground and meets the
following requirements:
Circuit Type.................... 220V, 60 Hz, Single-Phase
Circuit Size .................................................. 15A
Plug/Receptacle ................................... NEMA 6-15
W1769 Circuit Requirements
This machine is prewired to operate on a 220V power
supply circuit that has a verified ground and meets the
following requirements:
Circuit Type.................... 220V, 60 Hz, Three-Phase
Circuit Size .................................................. 15A
Plug/Receptacle ..................................NEMA 15-15
Full-Load Current Rating
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
W1768 at 220V, 1-Phase ........................ 4.2A/2.5A
W1769 at 220V, 3-Phase ........................ 3.4A/2.5A
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do so later in
this manual.
Incorrectly wiring or grounding this
machine can cause electrocution, fire,
or machine damage. To reduce this risk,
only an electrician or qualified service
personnel should do any required
electrical work on this machine.
NOTICE
The circuit requirements listed in this
manual apply to
a dedicated circuit—
where only one machine will be running
at a time. If this machine will be
connected to a shared circuit where
multiple machines will be running at the
same time, consult with an electrician
to ensure that the circuit is properly
sized for safe operation.

-10-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
ELECTRICAL
Grounding Requirements
This machine MUST be grounded. In the event of certain
types of
malfunctionsor breakdowns, grounding provides
a path of least resistance for electric current
to travel—in
order
to reduce the risk of electric shock.
Improper connection of the equipment-grounding
wire
will
increase
the risk of electric shock. The wire with green
insulation
(with/without yellow stripes)is the equipment-
grounding
wire. If repair or replacement of the power
cord or plug is necessary, do not connect the equipment-
grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel
if
you do not understand these grounding requirements,
or if
you are in doubt about whether the tool is
properly grounded.
If you ever notice that a cord or
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
Grounding Prong
Current Carrying Prongs
6-15 PLUG
GROUNDED
6-15 RECEPTACLE
220V
Figure 2. NEMA 6-15 plug & receptacle.
A NEMA 6-15 plug has a grounding prong that must be
attached to the equipment-grounding wire inside the
included power cord.
The plug must only be inserted
into a matching
receptacle (see Figure) that is properly
installed and grounded in accordance with all local codes
and ordinances.
W1768 220V Connection
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do later in
this manual.
Extension Cords
We do not recommend using an extension cord with
this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).
Any extension cord used with this machine must contain a
ground wire, match the required
plug and receptacle, and
meet the following requirements:
W1768 Minimum AWG ................ 16 AWG, 3W, 300V
W1769 Minimum AWG ................ 16 AWG, 4W, 300V
Maximum Length (Shorter is Better) ................50 ft.
Current
Carrying
Prongs
15-15 PLUG
GROUNDED
15-15 RECEPTACLE
Grounding Prong
Figure 3. NEMA 15-15 plug & receptacle.
No adapter should be used with the
required plug. If the plug does not fit
the available receptacle or the machine
must be reconnected to a different
type of circuit, the reconnection must
be made by an electrician or qualified
service personnel and it must comply
with all local codes and ordinances.
W1769 220V Connection
A NEMA 15-15 plug has a grounding prong that must be
attached to the equipment-grounding wire inside the
included power cord.
The plug must only be inserted
into a matching
receptacle (see Figure) that is properly
installed and grounded in accordance with all local codes
and ordinances.

-11-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SETUP
The following is a description of the main components
shipped with the Model W1768/W1769. Lay the
components out to inventory them.
Note: If you can't find an item on this list, check the
mounting location on the machine or examine the
packaging materials carefully. Occasionally we pre-install
certain components for safer shipping.
Box Inventory (Figures 4 & 5) Qty
A. Power Feeder Assembly ..................................1
B. Lubricator...................................................1
C. Base and Column Assembly ..............................1
D. Elbow Joint Assembly .....................................1
E. Base Bolt Pattern Template..............................1
F. Handwheel Handle ........................................1
G. Horizontal Column Assembly.............................1
H. Hex Bolts M12-1.75 x 50 (Not Shown)..................4
I. Lock Washers 12mm (Not Shown).......................4
Inventory
Keep machine disconnected from
power until instructed otherwise.
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
Unpacking
SETUP
Figure 4. Power feeder inventory.
A
Figure 5. Column and joint inventory.
C
E
D
F
G
B

-12-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SETUP
To prevent
corrosion during shipment and storage of your
machine, the factory has coated t
he bare metal surfaces
of your machine
with a heavy-duty rust prevention
compound
.
I
f you are unprepared or impatient, this compound can
be difficult to
remove. To ensure that the removal of this
coating is as easy as possible, please gather the correct
cleaner, lubricant, and tools listed below:
• Cleaner/degreaser
designed to remove storage wax
and grease
• Safety glasses & disposable gloves
•
Solvent brush or paint brush
• Disposable Rags
To
remove the rust preventative coating, do these
steps
:
1.
DISCONNECT THE MACHINE FROM POWER!
2.
Put on safety glasses and disposable gloves.
3
.Using a liberal amount of your cleaner/degreaser,
Coat all surfaces that have the coating,and let soak
for few minutes.
4
.Wipe off the surfaces. If your cleaner/degreaser is
effective, the coating will wipe off easily.
Tip: To clean off thick coats of the rust preventative
compound on flat surfaces, use a PLASTIC paint
scraper to scrape off the majority of the coating
before wiping it off with your rag. (Do not use a
metal scraper or you may scratch your machine.)
5
.Repeat the cleaning steps as necessary until all of
the compound is removed.
6
.To prevent rust on the freshly cleaned surfaces,
immediately coat with a quality metal protectant.
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoid
using these products
to clean machinery.
Many cleaning solvents
are toxic if inhaled.
Minimize your risk
by only using these
products in a well
ventilated area.
NOTICE
In a pinch, automotive degreasers,
mineral spirits or WD•40 can be used
to remove rust preventative coating.
Before using these products, though,
test them on an inconspicuous area of
your paint to make sure they will not
damage it.
Cleaning Machine

-13-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SETUP
To correctly position this power feeder on your table top,
first gather the stand parts shown in Figure 6, then
assemble the power feeder stand (refer to the parts
diagram for any intricate details).
Next, connect the stand to the power feeder, as shown
in Figure 7. With your power feeder unit completely
assembled, it will be easier for you to determine where
on the table top to drill your base mounting holes, so
you can take advantage of the full range of power feeder
swing and adjustments. Refer to Base Mounting on Page
14.
Assembly
Figure 7. Assembled power feeder.
You MUST assemble all guards, fences, and hold-
downs before starting your machine or power
feeder. Failure to heed this warning could result in
serious personal injury.
Figure 6. Item layout.

-14-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SETUP
Feed
Shaper
Cutter
Feed
Jointer
Cutterhead
Fence Fence
4th-Roller
Models
Feed
Table Saw
Blade
Fence
Optional
Featherboard
Figure 8. Typical power feed mounting on a shaper, jointer, and tablesaw.
Continued on next page
Position the power feeder on the table top to
determine where to drill your base mounting
holes, so you can maximize power feeder swing
and adjustment options.
There are two mounting options available:
Through Bolt Mounting and Direct Mounting
options discussed on Page 15. Choose an option
that suits your requirements.
Your final goal is to be able to use the handwheels
and lock levers to position the power feeder
wheels so they are parallel with the table
surface, and 1⁄8" lower than the thickness of your
workpiece.
Base Mounting
Also, you must be able to adjust the power
feeder so it points towards the machine fence
slightly (see Figure 8). In other words, the
tracking of the power feeder must be toed-in
approximately 1° to 1.5° degrees toward the
machine fence, so the power feeder wheels push
the workpiece against the fence slightly during
cutting operations.
If cutting long or large stock that is difficult to
feed properly, use a featherboard before the
powerfeeder (on the infeed side) to maintain
even pressure and control of the workpiece
against the fence.

-15-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SETUP
Figure 9. Through-bolt mounting.
Machine Table
Flat Washer
Flat Washer
Lock Washer
Locking Hex Nut
Table
Support
Webbing
Bolt
Feeder
Base
Figure 10. Direct mounting.
Machine Table
Table
Support
Webbing
Bolt
Feeder
Base
Lock Washer
Flat Washer
Apply A Medium
Grade Thread
Locking Compound
To The Threads
Through-Bolt Mounting
We recommend that you mount your new power feeder
to the machine table using the included M12-1.75 x 50
hex bolts and lock washers, plus additional flat washers
and locking hex nuts for a through-bolt setup (see Figure
9). This option will give the most rigidity and clamping
strength to prevent the feeder base from twisting out of
alignment during use. However, if under-table support
webs interfere with washer or nut locations under the
table, you must use an optional clamping kit, or drill and
thread holes directly into the table as described in the
Direct Mounting paragraph below.
Direct Mounting
Use the included mounting template to drill and tap your
table, so the power feeder base can be directly mounted
to the table surface (see Figure 10)using the included
M12-1.75 x 50 hex bolts and lock washers, plus additional
flat washers. If the table is thinner than 3⁄8" thick where
the threaded holes would be drilled and tapped, or if
support webbing is in the way, the threads may strip
or loosen as the power feeder is used. Thread locking
compound will not cure this situation. Revert to the
Through-Bolt Mounting option. In any case, make sure to
use a medium-grade liquid thread locking compound on all
threads.

-16-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
SETUP
Once power feeder assembly is complete and mounted on
the table, you must test run your power feeder to make
sure it runs properly. Your power feeder motor has two
feed speeds and two feed directions that are controlled at
the switch (see Figure 11).
If, during the test run, you cannot easily locate the source
of an unusual noise or vibration, stop using the power
feeder immediately, then review the Troubleshooting
table on Page 23.
If you still cannot remedy a problem, contact our
Technical Support at [phone] for assistance.
To test run the power feeder, do these steps:
1. Make sure you understand the safety instructions
at the beginning of the manual, and verify that the
power feeder is adjusted and is setup properly.
2. Make sure that the power feeder gearbox oil level is
full. The oil level should be 1" below the oil fill port.
Note: See Figure 15 on Page 21 for oil fill port
location.
3. Ensure that all tools and objects used during set up
are cleared away from the machine.
4. Adjust and lock the power feeder so the wheels are
held approximately one inch above the table and
nothing will interfere with wheel rotation.
5. Connect the power feeder to the power supply and
use the feed direction and speed switch (see Figure
11) to test operation in both feed directions.
— Listen and watch for abnormal noises or
vibrations. The power feeder should run smoothly.
— Correct for any unusual noises or vibrations before
operating the power feeder any further. Always
disconnect the power feeder from power when
investigating or correcting potential problems.
6. Turn the feed direction switch to OFF.
Test Run
Projectiles thrown from the machine
could cause serious eye injury. Wear
safety glasses to reduce the risk of
injury.
Loose hair and clothing could get
caught in machinery and cause serious
personal injury. Keep loose clothing
rolled up and long hair tied up and
away from machinery.
Figure 11. Feed direction and speed
switch.

-17-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
OPERATIONS
OPERATIONS
General
This machine will perform many types of operations
that are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed
incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary
knowledge and skills to operate this machine. If at
any time you experience difficulties performing any
operation, stop using the machine!
If you are an inexperienced operator, we strongly
recommend that you read books, trade articles, or seek
training from an experienced power feeder operator
before performing any unfamiliar operations. Above all,
your safety should come first!
Always wear safety glasses when oper-
ating this machine. Failure to comply
may result in serious personal injury.
DO NOT investigate problems or adjust
the machine while it is running. Wait
until the machine is turned OFF,
unplugged and all working parts
have come to a complete stop before
proceeding!
READ and understand this entire
instruction manual before using this
machine. Serious personal injury may
occur if safety and operational infor-
mation is not understood and followed.
DO NOT risk your safety by not reading!
Basic Use and Care
Power feeders reduce kickback hazards and improve
cutting results by feeding in a consistent and stable
manner. Remember, do not to stand in the path of
potential kickback. When not in use, support the power
feeder with a wooden block so the rubber wheels are
raised above the table and do not compress from the
weight of the power feeder.
The lock levers and handcranks allow you to adjust the
power feeder tracking and height to accommodate many
workpiece sizes. Before loosening any lock lever, always
support the power feeder with a block of wood, so the
power feeder does not drop and cause damage.
Adjust the power feeder so it is toed-in approximately
1° to 1.5° degrees towards the machine fence. This
adjustment will ensure the power feeder wheels slightly
push the workpiece against the fence during cutting
operations (see Figure 8 on Page 14). A featherboard
may be used on the infeed side to help feed long or large
stock.
Next, adjust the power feeder so the rubber wheels are
parallel with the table surface, and are 1⁄8"lower than
the thickness of your workpiece. This adjustment ensures
that the workpiece will not slip or hang in the middle of
a cut. Always double check that the power feeder wheels
are slightly lower than the workpiece before you begin
feeding operations. Otherwise, the workpiece may slip
and kickback.

-18-
Model W1768/W1769 (For Machines Mfg. Since 5/07)
OPERATIONS
Your power feeder has the option to feed a workpiece
at 13, 26, 33, and 66 feet per minute. These rates are
achieved by changing the combination of change gears,
shown in Figure 12, and turning the motor switch to high
or low range operation, shown in Figure 13.
To change the feed rate of your power feeder, do
these steps:
1. DISCONNECT THE MACHINE FROM POWER!
2. Make sure the speed dial is pointing to the OFF
position.
3. Refer to the feed rate list below to find the gear
combination required for your chosen feed rate.
Changing Feed Speed
MAKE SURE that your machine is
unplugged during all maintenance
procedures! If this warning is ignored,
serious personal injury may occur.
Figure 12. Change gear locations.
Change Gear
Position B
Change Gear
Position A
Figure 13. Feed direction and speed
switch.
Low Range Speed:
— A, 25 Tooth + B, 40 Tooth = 13 Ft Per Min.
Low Range Speed:
— A, 40 Tooth + B, 25 Tooth = 26 Ft Per Min.
High Range Speed:
— A, 25 Tooth + B, 40 Tooth = 33 Ft Per Min.
High Range Speed:
— A, 40 Tooth + B, 25 Tooth = 66 Ft Per Min.
Motor OFF.
4. Remove the chain cover and the two hex nuts
securing the A& Bchange gears to the shafts.
5. Swap the required change gears so the gear hubs are
facing toward the power feeder (shown in positions
A& Bin Figure 12).
6. Re-install the hex nuts and the chain cover.
7. Connect the power feeder to power and move the
feed direction and speed switch to High or Low
range.