Shop fox SHOP FOX W1811 User manual

OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 6/14)
MODEL W1811
10" SLIDING TABLE SAW
Phone: [phone] • Online Technical Support: [email protected]
COPYRIGHT © NOVEMBER, 2008 BY WOODSTOCK INTERNATIONAL, INC. REVISED SEPTEMBER, 2014 (BL)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
# 11153TR Printed in Taiwan

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

SETUPELECTRICAL MAINTENANCE SERVICE PARTS
OPERATIONS
SAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION .....................................2
Woodstock Technical Support .................. 2
Overview of Machine ............................ 2
Controls & Features ............................. 3
Machine Specifications .......................... 4
Sliding Table Saw Capacities ................... 6
SAFETY ...............................................8
Standard Machinery Safety Instructions ...... 8
Additional Safety for Sliding Table Saws ... 10
Preventing Kickback ........................... 11
Protecting Yourself From Kickback .......... 11
Glossary Of Terms .............................. 12
ELECTRICAL ....................................... 13
Circuit Requirements .......................... 13
Grounding Requirements...................... 14
Extension Cords ................................ 14
SETUP .............................................. 15
Items Needed for Setup....................... 15
Unpacking ....................................... 15
Inventory ........................................ 16
Machine Placement ............................ 18
Cleaning Machine............................... 18
Lifting & Moving ................................ 19
Assembly & Setup .............................. 20
Dust Collection ................................. 29
Test Run.......................................... 30
OPERATIONS....................................... 32
General .......................................... 32
Operation Overview ........................... 33
Workpiece Inspection.......................... 33
Non-Through & Through Cuts ................ 34
Blade Guard & Splitter/Riving Knife ........ 35
Safety Tips ...................................... 38
Blade Size Requirements...................... 39
Blade Selection ................................. 39
Changing Main Blade........................... 41
Changing/Adjusting Scoring Blade........... 42
Rip Cutting ...................................... 43
Crosscutting ..................................... 45
Miter Cutting.................................... 47
Dado Cutting .................................... 48
Rabbet Cutting ................................. 51
Resawing......................................... 53
SHOP-MADE SAFETY ACCESSORIES ............ 57
Featherboards .................................. 57
Push Sticks ...................................... 60
Push Blocks...................................... 61
Zero-Clearance Insert ......................... 62
Outfeed & Support Tables .................... 64
Crosscut Sled.................................... 64
ACCESSORIES ...................................... 65
Table Saw Accessories ......................... 65
MAINTENANCE .................................... 66
Schedule ......................................... 66
Cleaning ......................................... 66
Table & Base .................................... 66
Lubrication ...................................... 67
SERVICE ............................................ 68
General .......................................... 68
Belt Service ..................................... 68
Blade Tilt Calibration.......................... 69
Sliding Table Parallelism ...................... 70
Sliding Table Adjustment...................... 71
Calibrating Crosscut Fence 90° Stops....... 72
Splitter/Riving Knife Mounting Block ....... 73
Electrical Safety Instructions................. 74
Wiring Diagram ................................. 75
Electrical Pictures.............................. 76
Troubleshooting................................. 77
PARTS .............................................. 79
Labels & Cosmetics ............................ 79
Cabinet .......................................... 80
Trunnion ......................................... 81
Main Motor ...................................... 82
Tables ............................................ 86
Rip Fence........................................ 87
Handwheels ..................................... 88
Scoring Trunnion................................ 89
Crosscut Table .................................. 90
Swing Arm ....................................... 91
Miter Gauge ..................................... 92
Crosscut Fence ................................. 93
WARRANTY ........................................ 97
Contents

-2-
Model W1811 (For Machines Mfg. Since 11/13)
INTRODUCTION
Overview of Machine
A sliding table saw is primarily used to rip and crosscut sheet stock or panels in a production setting.
The sliding table makes it much easier and safer to feed these large workpieces through a cut. This saw
can also be used as a traditional table saw for most types of through-cuts.
The primary components of a sliding table saw are the sliding table, the fixed table, the crosscut table
and fence, the rip fence, the main blade and the scoring blade.
A typical cut using the sliding table is made by placing the workpiece on the sliding table and crosscut
table, positioning it against the crosscut fence where needed so the waste portion of the workpiece is on
the opposite side of the blade, and pushing the workpiece through the blade by sliding the table.
The scoring blade may or may not be used, depending on if the workpiece is faced with laminate,
melamine, or other solid surface material, or if tear-out free cuts are required. If the scoring blade
is not needed for cutting operations, it can be lowered under the table so it will stay sharp for later
operations.
When using the sliding table saw as a traditional table saw, the sliding table is locked in place and the
rip fence is then used to guide the workpiece through the cut.
In order to produce accurate results, the sliding table must move parallel to the blade and the scoring
blade must be aligned with the main blade. Similarly, the rip fence must be parallel with the main blade
and the crosscut fence must calibrated to the main blade.
Woodstock Technical Support
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
In the event that questions arise about your machine, please contact Woodstock International Technical
Support at [phone] or send e-mail to: [e-mail]. Our knowledgeable staff will
help you troubleshoot problems or process warranty claims.
INTRODUCTION
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [e-mail]

-3-
Model W1811 (For Machines Mfd. Since 6/14)
INTRODUCTION
Controls & Features
Figure 1. Main view of machine features and controls.
C
G
H
A. Crosscut Table: Provides a wide, stable
platform for supporting full-size panels
during crosscutting operations. Also fea-
tures an angle scale for cutting miters with
the crosscut fence.
B. Flip Stops: Used for quick measurements
when crosscutting.
C. Crosscut Fence: Used during crosscutting
operations. Features a scale and multiple
flip-style stop blocks (a.k.a. "flip stops")
for precise, repeatable crosscutting opera-
tions. Can also be set up for miter cuts.
D. Sliding Table: Conveniently glides the
workpiece through the blade with effort-
less precision and ease.
E. Blade Guard: Fully-adjustable blade guard
maintains maximum protection around the
saw blade and a 2½" dust port effectively
extracts dust from the cutting operation.
F. Rip Fence: Fence face can be positioned
for standard cutting operations, or in the
lower position for blade guard clearance
during narrow ripping operations.
G. ON/OFF Switch: Starts and stops main
blade and scoring blade motors. Features
an OFF switch that must be reset between
starting and stopping machine.
H. Blade Angle Handwheel: Adjusts the angle
of the saw blades.
I. Blade Elevation Handwheel: Located on
the right-hand side of the cabinet, this
handwheel adjusts the height of the main
saw blade.
A
DE
BF
I
Fence
Positions

-4-
Model W1811 (For Machines Mfg. Since 11/13)
INTRODUCTION
Model W1811 Machine Specifications, Page 1 of 3
MODEL W1811
SHOP FOX® 5 HP 10" SLIDING TABLE SAW
Product Dimensions
Weight.......................................................................................................... 533 lbs.
Width (side-to-side) x Depth (front-to-back) x Height.................................. 76 x 124-3/4 x 46 in.
Footprint (Length x Width)......................................................................... 25-1/5 x 28 in.
Shipping Dimensions
Carton #1
Type................................................................................................ Wood Crate
Content................................................................................................. Machine
Weight................................................................................................... 569 lbs.
Length x Width x Height..................................................................... 42 x 46 x 42 in.
Must Ship Upright............................................................................................ No
Carton #2
Type............................................................................................. Cardboard Box
Content........................................................................................... Sliding Table
Weight................................................................................................... 119 lbs.
Length x Width x Height..................................................................... 66 x 19 x 10 in.
Must Ship Upright............................................................................................ No
Electrical
Power Requirement.................................................................... 230V, Single-Phase, 60 Hz
Full-Load Current Rating......................................................................................... 19A
Minimum Circuit Size............................................................................................. 30A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................... 6 ft.
Power Cord Gauge............................................................................................ 12 AWG
Plug Included....................................................................................................... Yes
Included Plug Type.............................................................................................. L6-30
Switch Type............................................................ Magnetic Switch w/Overload Protection
Motors
Main
Type......................................................................... TEFC Capacitor-Start Induction
Horsepower................................................................................................. 5 HP
Phase.............................................................................................. Single-Phase
Amps.......................................................................................................... 19A
Speed.................................................................................................. 3450 RPM
Power Transfer ................................................................................... V-Belt Drive
Bearings................................................................. Sealed & Permanently Lubricated
Machine Specifications

-5-
Model W1811 (For Machines Mfd. Since 6/14)
INTRODUCTION
Model W1811 Machine Specifications, Page 2 of 3
Main Specifications
Operation Information
Main Blade Size........................................................................................... 10 in.
Main Blade Arbor Size.................................................................................. 5/8 in.
Scoring Blade Size.................................................................................... 3-1/8 in.
Scoring Blade Arbor Size............................................................................... 22 mm
Maximum Width of Dado............................................................................ 13/16 in.
Main Blade Tilt..................................................................................... 0 – 45 deg.
Main Blade Speed.................................................................................... 4000 RPM
Scoring Blade Tilt.................................................................................. 0 – 45 deg.
Scoring Blade Speed................................................................................. 8000 RPM
Cutting Capacities
Max Depth of Cut At 90 Deg........................................................................ 3-1/8 in.
Max Depth of Cut At 45 Deg........................................................................ 2-1/4 in.
Rip Fence Max Cut Width............................................................................... 33 in.
Sliding Table w/Crosscut Fence Max Cut Width................................................ 78-1/2 in.
Sliding Table w/Crosscut Fence Max Cut Length.................................................... 63 in.
Miter Fence Max Cut Width at 45 Deg................................................................ 63 in.
Table Information
Floor To Table Height............................................................................... 33-5/8 in
Table Size Length........................................................................................ 27 in.
Table Size Width.................................................................................... 14-3/8 in.
Table Size Thickness...................................................................................... 2 in.
Table Size With Ext Wings Length..................................................................... 47 in.
Table Size With Ext Wings Width...................................................................... 40 in.
Table Size With Ext Wings Thickness................................................................... 2 in.
Sliding Table Length..................................................................................... 63 in.
Sliding Table Width................................................................................. 12-1/4 in.
Sliding Table Thickness.............................................................................. 3-1/2 in.
Sliding Table T-Slot Top Width....................................................................... 5/8 in.
Sliding Table T-Slot Height............................................................................ 1/2 in.
Sliding Table T-Slot Bottom Width................................................................ 1-1/4 in.
Fence Information
Crosscut Fence Type......................................... Single Lever Locking, Extruded Aluminum
Crosscut Fence Size Length....................................................................... 33-1/2 in.
Crosscut Fence Size Width............................................................................... 2 in.
Crosscut Fence Size Height......................................................................... 4-1/4 in.
Crosscut Fence Number of Stops............................................................................ 2
Construction Materials
Table............................................................................. Precision-Ground Cast Iron
Sliding Table......................................................................................... Aluminum
Cabinet..................................................................................................... Steel
Rip Fence Rails............................................................................... Hardened Steel
Guard..................................................................................................... Plastic
Spindle Bearing Type......................................................... Radial Ball Bearing 6004LLB
Cabinet Paint Type/Finish.................................................................. Powder Coated
Other Related Information
No of Dust Ports................................................................................................ 2
Dust Port Size...................................................................................... 4, 2-1/2 in.

-6-
Model W1811 (For Machines Mfg. Since 11/13)
INTRODUCTION
Model W1811 Machine Specifications, Page 3 of 3
Other
Country of Origin ............................................................................................. Taiwan
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time ............................................................... 1-1/2 Hours
Serial Number Location ........................................................... ID Label on Front of Machine
ISO 9001 Factory ................................................................................................... No
CSA, ETL, or UL Certified/Listed ............................................................................... Yes
Features
4" Main Dust Port
Adjustable Scoring Knife Kerf
Adjustable Riving Knife
Single Lever Locking Fence
Blade Guard with 2-1/2" Dust Port
Dadoes Up To 13/16"
Sliding Table Saw Capacities

-7-
Model W1811 (For Machines Mfd. Since 6/14)
SAFETY
Ripping Width
Miter Cut 90º
(push cut)
Miter Cut 45º
Miter Cut 45º
(push cut)
Cross Cut
(fence not extended)
Miter Cut 45º
(push cut, fence not extended)
Miter Cut 45º
(fence not extended)
Cross Cut
Phone #: [phone] • Online Tech Support: [e-mail] • Web: www.shopfox.biz
SLIDING TABLE
SAW CAPACITIES
moDEL W1811 10" SLIDING TABLE SAW
33"
78-1/2"
63"
50"
68"
48"
48-3/4"
63"
78-3/4"
44-1/2"
31-1/2"
48-3/4"
44-1/2"
31-1/2"
78-3/4"
63"
48"
78-3/4"
37"

-8-
Model W1811 (For Machines Mfd. Since 6/14)
SAFETY
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.
NOTICE
SAFETY
OWNER’S MANUAL.
Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY.
Untrained operators
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
DANGEROUS ENVIRONMENTS.
Do not use
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
MENTAL ALERTNESS REQUIRED.
Full mental
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
ELECTRICAL EQUIPMENT INJURY RISKS. You can
be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
Standard Machinery Safety Instructions
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-
sures—this responsibility is ultimately up to the operator!
SAFETY
Standard Machinery Safety Instructions

-9-
Model W1811 (For Machines Mfd. Since 6/14)
SAFETY
WEARING PROPER APPAREL. Do not wear
clothing, apparel,or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.
HAZARDOUS
DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
HEARING PROTECTION.
Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
REMOVE ADJUSTING TOOLS.
Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!
INTENDED USAGE.
Only use machine for its
intended purpose—never make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leadsto serious
personal injury or death!
AWKWARD POSITIONS.
Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
CHILDREN & BYSTANDERS.
Keep children and
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.
GUARDS & COVERS.
Guards and covers reduce
accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury may
occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during
operation greatly increases risk of injury or
loss of control. Before starting, verify machine
is stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.
UNATTENDED OPERATION. To reduce the risk
of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could
malfunction, leading to serious personal injury
or death.
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away
from heated surfaces, high traffic areas, harsh
chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the
intended operation, stop using the machine!
Contact Technical Support at [phone].

-10-
Model W1811 (For Machines Mfd. Since 6/14)
SAFETY
Additional Safety for Sliding Table Saws
HAND & BODY POSITIONING.Touching a spinning
saw blade will cause serious laceration or amputa-
tion injuries.
Keep hands away from saw blade and
out of
blade path during operation, so they cannot
slip accidentally into blade. Stand to side of blade
path.
Never reach around, behind, or over blade.
Only operate at front of machine; never operate
from rear or sides of saw.
BLADE GUARD.
Use blade guard for all “through
cuts” for which it can be used. (A through cut is an
operation where blade cuts completely through the
top of the workpiece.) Make sure the blade guard
is installed and adjusted correctly; promptly repair
or replace it if damaged. Always re-install blade
guard immediately after operations that require its
removal. Operating saw with blade guard removed
greatly increases risk of severe laceration or ampu-
tation injuries from accidental blade contact.
RIVING KNIFE.
Use the riving knife for all “non-
through cuts” for which it can be used. (A non-
through cut is an operation where the blade does
not cut through the top of the workpiece.) Make
sure the riving knife is aligned and positioned
correctly; and promptly repair or replace it if
damaged. Using the riving knife incorrectly will
increase the risk of kickback or accidental blade
contact.
KICKBACK.
Kickback occurs when the saw blade
ejects the workpiece back toward the operator.
Know how to reduce the risk of kickback, and learn
how to protect yourself if it does occur.
FEEDING WORKPIECE.
Feeding workpiece incor-
rectly will increase risk of kickback. Never start
saw with a workpiece touching blade; allow blade
to reach full speed before cutting. Only feed work-
piece against direction of blade rotation, from
front of saw. Never pull workpiece from behind
blade. Always use some type of guide (fence, miter
gauge, sliding table or sled, etc.) to feed workpiece
in a straight line. Never back a workpiece out of a
cut or move it backwards or sideways after starting
a cut. Feed cuts all the way through to completion.
Never perform any operation “freehand” (making
a cut without using a fence, miter gauge, or other
guide). Never plunge cut.
FENCE. Make sure the fence remains properly
adjusted and parallel with the blade. Always lock
the fence in place before using. Using or adjusting
the fence incorrectly will increase risk of kickback.
PUSH STICKS/BLOCKS.
Use push sticks or push
blocks whenever possible to keep your hands far-
ther away from the blade while cutting; in the
event of an accident these devices will often take
damage that would have happened to hands/fin-
gers.
CUT-OFF PIECES.
Never use your hands to move
cut-offs away from the blade while the saw is run-
ning. If a cut-off becomes trapped between the
blade and table insert, turn the saw OFF
and allow
the blade to completely stop before removing it.
BLADE ADJUSTMENTS.
Adjusting the blade height
or tilt during operation increases the risk of crash-
ing the blade and sending metal fragments flying
with deadly force at the operator or bystanders.
Only adjust the blade height and tilt when the
blade is completely stopped and the saw is OFF.
CHANGING BLADES.
Always disconnect power
before changing blades. Changing blades while the
saw is connected to power greatly increases the
injury risk if saw is accidentally powered up.
DAMAGED SAW BLADES.
Never use blades that have
been dropped or otherwise damaged. Damaged
blades can fly apart and strike the operator with
shards of metal.
DADO AND RABBET OPERATIONS.
DO NOT attempt
dado or rabbeting operations without first reading
those sections in this manual. Dado and rabbeting
operations require special attention because they
must be performed with the blade guard removed.
CUTTING CORRECT MATERIAL. Never cut materi-
als not intended for this saw; only cut natural and
man-made wood products, laminate covered wood
products, and some plastics.
Cutting metal, glass,
stone, tile, etc. increases the risk of operator
injury due to kickback or flying particles.

-11-
Model W1811 (For Machines Mfd. Since 6/14)
SAFETY
Below are preventative meaures to avoid the
most common causes of kickback:
• Only cut workpieces with at least one
smooth and straight edge. DO NOT cut
warped, cupped or twisted wood.
• Never attempt freehand cuts. If the
workpiece is not fed parallel with the
blade, kickback will likely occur. Always use
the rip fence or miter gauge to support the
workpiece.
• Make sure the splitter/riving knife is
aligned with the blade. A misaligned split-
ter/riving knife can cause the workpiece
to catch or bind, increasing the chance of
kickback. If you think that your splitter/
riving knife is not aligned with the blade,
check it immediately!
• Take the time to check and adjust the rip
fence parallel with the blade. Also, ensure
that your table slides parallel with the
blade. If either of these two elements are
not adjusted correctly, the risk of kickback
will be greatly increased.
• Do not remove the splitter/riving knife.
The splitter/riving knife maintains the kerf
in the workpiece, reducing the chance of
kickback from the workpiece halves pinch-
ing the blade.
• Feed cuts through to completion. Anytime
you stop feeding a workpiece in the middle
of a cut, the chance of kickback is greatly
increased.
• Keep the blade guard installed and in good
working order. Only remove it when per-
forming non-through cuts and immediately
re-install the blade guard when finished.
Remember, always use the splitter/riving
knife for all non-through operations, unless
a dado blade is installed.
• Make multiple, shallow passes when per-
forming a non-through cut. Making a deep
non-through cut will greatly increase the
chance of kickback.
Statistics show that most common acci-
dents among table saw users can be linked
to kickback. Kickback is typically defined
as the high-speed expulsion of stock from
the table saw toward its operator. In addi-
tion to the danger of the operator or others
in the area being struck by the flying stock,
it is often the case that the operator’s
hands are pulled into the blade during the
kickback.
Preventing Kickback
Even if you know how to prevent kickback, it
may still happen.
Here are some preventative meaures to
protect yourself if kickback DOES occur:
• Stand to the side of the blade during every
cut. If a kickback does occur, the thrown
workpiece usually travels directly in front
of the blade.
• Wear safety glasses or a face shield. In the
event of a kickback, your eyes and face are
the most vulnerable part of your body.
• Never, for any reason, place your hand
behind the blade. Should kickback occur,
your hand will be pulled into the blade.
• Use a push stick to keep your hands farther
away from the moving blade. If a kickback
occurs, the push stick will most likely take
the damage that your hand would have
received.
• Keep the blade guard installed and in good
working order.
• Use featherboards or anti-kickback devices,
such as Shop Fox Board Buddies, to prevent
or slow down kickback.
Protecting Yourself
From Kickback

-12-
Model W1811 (For Machines Mfd. Since 6/14)
SAFETY
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this table saw and woodworking in general. Become familiar with these terms for assembling, adjusting
or operating this machine.
Arbor: A metal shaft extending from the drive
mechanism that is the mounting location for the
saw blade.
Bevel Edge Cut: Tilting the arbor and saw
blade to an angle between 0˚ and 45˚ to cut a
beveled edge onto a workpiece.
Blade Guard Assembly: Metal or plastic safety
device that mounts over the saw blade. Its
function is to prevent the operator from coming
into contact with the saw blade. Refer to Page
35 for more details.
Crosscut: Cutting operation in which the
crosscut fence is used to cut across the shortest
width of the workpiece. Refer to Page 45 for
more details.
Dado Blade: Blade or set of blades that are
used to cut grooves and rabbets. DO NOT use
a dado blade larger than 8" in diameter on this
saw! The saw and arbor are not intended to
safely use a larger dado blade.
Dado Cut: Cutting operation that uses a dado
blade to cut a flat bottomed groove into the
face of the workpiece. Refer to Page 49 for
more details.
Featherboard: Safety device used to keep the
workpiece against the rip fence and against
the table surface. Refer to Page 57 for more
details.
Kerf: The resulting cut or gap in the workpiece
after the saw blade passes through during a
cutting operation.
Kickback: An event in which the workpiece is
propelled back towards the operator at a high
rate of speed.
Non-Through Cut: A cut in which the blade
does not cut through the top of the workpiece.
Refer to Page 34 for more details.
Parallel: Being an equal distance apart at every
point along two given lines or planes (i.e. the
rip fence face is parallel to the face of the saw
blade).
Perpendicular: Lines or planes that intersect
and form right angles (i.e. the blade is
perpendicular to the table surface).
Push Stick: Safety device used to push the
workpiece through a cutting operation. Used
most often when rip cutting thin workpieces.
Refer to Page 60 for more details.
Rabbet: Cutting operation that creates an
L-shaped channel along the edge of the
workpiece. Refer to Page 51 for more details.
Rip Cut: Cutting operation in which the rip
fence is used to cut across the width of the
workpiece. Refer to Page 43 for more details.
Splitter/Riving Knife: Metal plate located behind
the blade. It maintains the kerf opening in the
wood when performing a cutting operation.
Refer to Page 35 for more details.
Straightedge: A tool used to check the flatness,
parallelism, or consistency of a surface(s).
Thin Kerf Blade: A blade with a kerf or
thickness that is thinner than a standard blade.
Since thin kerf blades are typically the same
thickness of the splitter/riving knife—and in
some cases thinner—we DO NOT recommend
that they be used on this saw due to the
increased risk of kickback.
Through Cut: A cut in which the blade cuts
completely through the workpiece. Refer to
Page 34 for more details.
Zero Clearance Table Insert: An aftermarket or
shop-made table insert specifically modified for
the installed blade to eliminate clearance around
the blade.
Glossary Of Terms

-13-
Model W1811 (For Machines Mfd. Since 6/14)
ELECTRICAL
ELECTRICAL
Circuit Requirements
This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the full-
load current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
Full-Load Current Rating
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
Full-Load Current Rating at 230V .................. 19 Amps
Circuit Requirements for 230V
Circuit Type ............................230V, 60 Hz, 1-Phase
Circuit Size ............................................. 30 Amps
Plug/Receptacle ...........................................L6-30
This machine is prewired to operate on a 230V power
supply circuit that has a verified ground and meets the
following requirements:
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do so later in
this manual.
Incorrectly wiring or grounding this
machine can cause electrocution, fire,
or machine damage. To reduce this risk,
only an electrician or qualified service
personnel should do any required
electrical work on this machine.
NOTICE
The circuit requirements listed in this
manual apply to
a dedicated circuit—
where only one machine will be running
at a time. If this machine will be
connected to a shared circuit where
multiple machines will be running at the
same time, consult with an electrician
to ensure that the circuit is properly
sized for safe operation.

-14-
Model W1811 (For Machines Mfd. Since 6/14)
SETUP
Grounding Requirements
This machine MUST be grounded. In the event of certain
types of
malfunctionsor breakdowns, grounding provides
a path of least resistance for electric current
to travel—in
order
to reduce the risk of electric shock.
Improper connection of the equipment-grounding
wire
will
increase
the risk of electric shock. The wire with green
insulation
(with/without yellow stripes)is the equipment-
grounding
wire. If repair or replacement of the power
cord or plug is necessary, do not connect the equipment-
grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel
if
you do not understand these grounding requirements,
or if
you are in doubt about whether the tool is
properly grounded.
If you ever notice that a cord or
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
Grounding Prong
is Hooked
Current Carrying Prongs
L6-30 GROUNDED
LOCKING
RECEPTACLE
L6-30
LOCKING
PLUG
Figure 2. NEMA L6-30 plug & receptacle.
Extension Cords
We do not recommend using an extension cord with
this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).
Any extension cord used with this machine must contain a
ground wire, match the required
plug and receptacle, and
meet the following requirements:
Minimum Gauge Size at 230V ........... 10 AWG, 3-Wire
Maximum Length (Shorter is Better) ................50 ft.
This machine is equipped with a power cord that has an
equipment-grounding
wire and NEMA L6-30 grounding
plug.
The plug must only be inserted into a matching
receptacle (
see Figure) that is properly installed and
grounded in accordance with local codes and ordinances.
For 230V Connection
No adapter should be used with the
required plug. If the plug does not fit
the available receptacle or the machine
must be reconnected to a different
type of circuit, the reconnection must
be made by an electrician or qualified
service personnel and it must comply
with all local codes and ordinances.
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do so later in
this manual.

-15-
Model W1811 (For Machines Mfd. Since 6/14)
SETUP
Keep machine disconnected from
power until instructed otherwise.
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
Unpacking
SETUP
The following items are needed to complete the setup
process, but are not included with your machine:
Description Qty
• Safety Glasses (for each person)........................1
• Forklift ......................................................1
• Lifting Straps (2000 lb capacity) ........................2
• An Assistant.................................................1
• Straightedge 4' (or longer) ...............................1
• Table Saw Blade 10".......................................1
• Phillips Head Screwdriver #2 ............................1
• Hex Wrenches 3, 4, 5, 6, & 8mm ................ 1 Each
• Dust Collection System ...................................1
• 4" Dust Hose (length as needed) ........................1
• 4" Hose Clamp..............................................2
• 2½" Dust Hose (length as needed)......................1
Items Needed for Setup

-16-
Model W1811 (For Machines Mfd. Since 6/14)
SETUP
The following is a description of the main components
shipped with the Model W1811. If you can't find an
item on this list, check the mounting location on the
machine or examine the packaging materials carefully.
Occasionally we pre-install certain components for
safer shipping. If you still can't find a part, talk to your
authorized Shop Fox dealer.
Inventory Contents
Inventory Item: (Figures 3–6) Qty
A. Table Saw (not shown)....................................1
B. Large Extension Table.....................................1
C. Small Extension Table.....................................1
D. Hose Support ...............................................1
E. Crosscut Fence.............................................1
F. Support Bar.................................................1
G. Crosscut Table..............................................1
H. Crosscut Table Support Leg ..............................1
I. Flip Stops ...................................................2
J. Lock Lever M12-1.75 x 55 ................................1
K. Flat Washer 12mm.........................................1
L. T-Nut M12-1.75.............................................1
M. Rip Fence Rail (w/Attached Mounting Hardware) .....1
N. Rip Fence ...................................................1
O. Rip Fence Scale ............................................1
P. Rip Fence Lever w/Hex Nut M8-1.25 ....................1
Q. Rip Fence Base .............................................1
R. Blade Guard w/Cap Screw & Nut ........................1
S. Arbor Lock Tool ............................................1
T. Sliding Table Handle w/Lock .............................1
U. Push Stick ...................................................1
V. Splitter/Riving Knife .......................................1
W. End Cover ...................................................1
X. Wrench 17mm (not shown) ...............................1
Y. Wrench 19/22mm (not shown) ...........................1
Inventory
Figure 3. Extension table items.
B
C
D
Figure 4. Crosscut table items.
EF
I
G
L
K
J
H
Figure 5. Rip fence items.
N
O
M
P
Q
Figure 6. Miscellaneous components.
R
S
V
T
W
U

-17-
Model W1811 (For Machines Mfd. Since 6/14)
SETUP
Inventory Item: (Figure 7–9) Qty
AA. Miter Clamp ................................................1
AB. Miter Flip Stop .............................................1
AC. Miter Handle w/Flat Washer 8mm ......................1
AD. Miter Gauge Fence ........................................1
AE. Miter Gauge Body..........................................1
AF. Miter Guide Bar ............................................1
AG. Sliding Table................................................1
AH. Sliding Table Support Legs ...............................2
AI. Feet M12-1.75 x 75 w/Nuts ..............................2
AJ. Crosscut Brace Knobs M8-1.25 x 50.....................2
—Flat Washers 8mm .......................................2
—Square Nuts M8-1.25 ....................................2
AK. Crosscut Fence Knob M8-1.25 ...........................1
—Flat Washer 8mm ........................................1
—Crosscut Fence T-Stud M8-1.25 x 60..................1
AL. Crosscut Fence Lock Knob M8-1.25 x 25 ...............1
AM. Pivot Stud ...................................................1
—Special Washer 8 x 20mm ..............................1
—Square Nut M8-1.25 .....................................1
AN. Push Handle M12-1.75 x 14 ..............................1
—Flat Washer 12mm.......................................1
—Plastic Washer 12mm ...................................1
—Push Handle T-Nut M12-1.75...........................1
AO. Support Leg T-Slot Plates ................................2
AP. Sliding Table T-Studs M12-1.75 x 35 ....................2
—Flat Washers 12mm .....................................2
—Lock Washers 12mm.....................................2
—Hex Nuts M12-1.75 ......................................2
Other Hardware (not shown) Qty
• Cap Screws M10-1.5 x 25 (Extension Tables)..........5
• Flat Washers 10mm (Extension Tables) ................5
• Lock Washers 10mm (Extension Tables)................5
• Set Screws M8-1.25 x 25 (Extension Tables) ..........6
• Hex Nuts M8-1.25 (Extension Tables)...................6
• Hex Bolts M6-1 x 16 (Fence Scale)......................2
• Hex Bolt M6-1 x 25 (Fence Scale).......................1
• Flat Washers 6mm (Fence Scale) .......................3
• Lock Washers 6mm (Fence Scale).......................3
• Hex Nuts M6-1 (Fence Scale) ............................3
• Cap Screws M6-1 x 16 (CT Support Leg) ...............4
• Lock Washers 6mm (CT Support Leg) ..................4
• Flat Washers 6mm (CT Support Leg) ...................4
• Cap Screws M5-.8 x 12 (Switch).........................2
• Lock Washers 5mm (Switch) .............................2
• Cap Screws M10-1.5 x 30 (ST Leg Plates)..............4
• Lock Washers 10mm (ST Leg Plates) ...................4
• Cap Screw M10-1.5 x 25 (Hose Support)...............1
• Flat Washers 10mm (Hose Support) ....................2
• Hex Nut M10-1.5 (Hose Support)........................1
Figure 7. Miter gauge items.
AA
AC
AD
AE
AF
AB
Figure 8. Sliding table items.
AG
AH
AI
Figure 9. Miscellaneous knobs and
hardware.
AJ
AK
AL
AM
AN
AO
AP

-18-
Model W1811 (For Machines Mfd. Since 6/14)
SETUP
• Floor Load: This machine distributes a
heavy load in a small footprint. Make
sure the floor will support the machine,
workpieces, and the operator.
• Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your machine (see Figure 10).
• Lighting: Lighting should be bright enough
to eliminate shadows and prevent eye
strain.
Cleaning Machine
The table and other unpainted parts of your
machine are coated with a waxy grease that
protects them from corrosion during shipment.
Clean this grease off with a solvent cleaner or
citrus-based degreaser. DO NOT use chlorine-
based solvents such as brake parts cleaner or
acetone—if you happen to splash some onto a
painted surface, you will ruin the finish.
Machine Placement
USE helpers and power
lifting equipment to lift
this machine. Otherwise,
serious personal injury
may occur.
NEVER clean with gasoline
or other petroleum-
based solvents. Most have
low flash points, which
make them extremely
flammable. A risk of
explosion and burning
exists if these products
are used. Serious personal
injury may occur if this
warning is ignored!
123"
150"
71"
Figure 10.Working clearances.