Shoremaster 1007970 User manual

SHOREMASTER.COM
SWIm RAftS
SWIm RAftS
A
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
QC Connector Bracket
1004187
-
1
T Handle
100087612
Carriage Bolt 3/8 x 1.75
100195923
Flange Nut 3/8
100180224
NUT 3/8
10018031
5
4 2
5
3
1
Failure to follow instructions may
result in personal injury and may
invalidate the applicable warranty.
Step 1. Attach the QC Connector Bracket
to the TS9 Frame with two 3/8 x 1 3/4
Carriage Bolts and two 3/8 Flange Nuts - as
shown.
Note: The QC Bracket must be bolted to the
TS9 Frame
Note: The TS9 Frame must be supported
by legs.
Step 2. Set the 9" Truss Dock onto the QC
Brackets and secure using the T-Handles.
QC Connector TS9 to Truss Dock
Instructions
Part #: 1004187
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
3 STEP LADDER FRAME LEFT
100561511
3 STEP LADDER FRAME RIGHT
100561612
Prt Ladder Step 15.0
100578533
Bolt Carriage 1/4-20 x .75 SS 304
10019501 24
1/4" NUT BRASS
100179712
5
POLY WASHER 3/8 ID X 1"OD X .093
100246926
Pin Snap 3/8 x 1.75
10003382
7
Washer Flat 3/8 SS
100259948
Nut Nyloc 3/8-16 Brass
100180529
Ladder Pivot Left
100177811 0
Ladder Pivot Right100177911 1
BOLT 3/8" x 2.0 PHILLIPS MACH SCREW
100242621 2
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
Swim Raft Rubber Anchor Hold
100109421
3 Step Pivoting Ladder
100763412
Ladder Brace
100497913
3/8 X 6-1/2 Hex Bolt
100244724
3/8" Washer
10025996
5
3/8 Nyloc Nut
100180526
3/8 X 1 Hex Bolt
10024192
7
3/8 Lock Washer
100259628
D
See 1006596 - Pivoting Ladder instructions
for assembly and operating steps.
12
6
8
6
8
9
4
3
2
1
10
5
7
11
Poly Swim Raft w/3 Step Ladder
Instructions
Part #: 1007970 - Yellow
1007980 - Grey
1024603 - Tan
5
8
7
235
6
1
4
5
Attach Ladder
Step 1. The rear of each Ladder Pivot is bolted through the
hole marked on the drawing as Hole Location. Two 3/8" x
6-1/2" bolts and two 3/8" washers are placed through the
rear of each ladder pivot. The bottoms of the two bolts are
secured through a Ladder Brace using two 3/8" washers and
two 3/8" Nyloc nuts.
Step 2. The front of each Ladder pivot is bolted into a
threaded insert molded into the raft using two 3/8" x 1" bolts,
two 3/8" washers and two 3/8" lock washers on top.
Hole
Location
Failure to follow instructions may result in personal injury and may invalidate the
applicable warranty.

SHOREMASTER.COM
SWIm RAftS
Attach Anchor Ring
Step 1. One end of the 15' rope is threaded through the cone shaped thru-hole in the raft from the bottom
up through the top. Next thread the rope through the rubber cone and tie a couple knots so the rope will not
pull through the cone.
Step 2. The Anchor Ring is then threaded on the 15' rope.
Step 3. The loose end of the rope is then attached in the same manner as the other end to the other side
of the raft through the second rubber cone.
Step 4. The anchor rope is attached to the Anchor Ring. The purchaser provides the anchor rope and the
anchor. Anchor rope should be rope and not chain.
The anchor tie downs should not be used to pull the raft through the water behind a boat or
onto shore. If the raft is exposed to heavy or continuous wave action, a rope snubber should be added to
the anchoring line to help absorb the shocks.
Never jump or dive into the water before the entire subsurface area has been checked for
depth. Consult local authorities for ordinances regarding proper placement and anchoring of swim raft.
Manufacturer recommends removing swim raft from water when not in use. ALWAYS PUT SAFETY
FIRST!
Rubber Anchor Hold
Poly
Swim
Raft
15' Rope
Anchor Ring
Drain Plug
Anchor Rope
(Not Included)