Shunxun SX-SPH4-100 Troubleshooting guide

Operating Instructions
1
Quick Start Guide
Features
•Incorporates HD Base-T technology
•Distributes 1 HDMI source to 4 HDMI Displays simultaneously.
•Full HD support: 1080p@60Hz@48 b/pixels, support 3D and 4Kx2K
•Extends HDMI and IR up to 328 feet (100 meters) using one CAT5e (or better) cable
•With Infrared control signal passing through function.
•Supports high bit-rate audio formats (Dolby True-HD / DTS Master Audio )
•100BaseT Ethernet &RS-232 Pass-Through (Output1)
•HDCP compliant.
•CEC Pass-Through
•DC 12V power supply
4-PORT HDBaseT SPLITTER
Features
•Incorporates HD Base-T technology
•Distributes 1 HDMI source to 4 HDMI Displays simultaneously.
•Full HD support: 1080p@60Hz@48 b/pixels, support 3D and 4Kx2K
•Extends HDMI and IR up to 328 feet (100 meters) using one CAT5e (or better) cable
•With Infrared control signal passing through function.
•Supports high bit-rate audio formats (Dolby True-HD / DTS Master Audio )
•100BaseT Ethernet &RS-232 Pass-Through (Output1)
•HDCP compliant.
•CEC Pass-Through
•DC 12V power supply
4-PORT HDBaseT SPLITTER
Compliant HDCP

Operating Instructions
2
Packing contents
1) Main Unit: 1x4 HDBaseT Splitter
2) Power supply DC 12V 2A
3) IR-TX cable x 4PCS
4) IR-RX cable x 4 PCS
5) M3x5 Screw x 6PCS
6) Operating Instructions
7) Mounting ear
Dimensional drawing
TABLE OF CONTENTS
Package Contents
Dimensional drawing
Panel Descriptions
Connecting and Operating
Typical Application
Maintenance
Product Service
Warranty
295mm
33mm
160mm
Packing contents
1) Main Unit: 1x4 HDBaseT Splitter
2) Power supply DC 12V 2A
3) IR-TX cable x 4PCS
4) IR-RX cable x 4 PCS
5) M3x5 Screw x 6PCS
6) Operating Instructions
7) Mounting ear
Dimensional drawing
TABLE OF CONTENTS
Package Contents
Dimensional drawing
Panel Descriptions
Connecting and Operating
Typical Application
Maintenance
Product Service
Warranty
295mm
33mm
160mm
8

Operating Instructions
3
-5 to +35 C(+23 to +95 F)
5 to 90%RH (No Condensation)
300MHz/9Gbps
Up to 1080p@60Hz@48 b/pixels, support 3D ,4K
HDMI receptacle.
RJ45
Power connector terminal
Power DC receptacle
IR Blaster
D-Type 9pin plug
1080P 328FT/100m over single CAT5E/6 cable
110-240V/ 12VDC 2A power supply
12Watts
Cold-Rolled (Cold Rolled) Steel
W295xH160xT33mm
1400g

Operating Instructions
4
Front Panel
Rear Panel
Power ON/OFF
Status indicator lamp:The LED will illuminate when the HDMI equipment is connected.
Power indicator lamp:The LED will illuminate when the power is on.
Reset key
Power input port
1 3
2
4
RS232 port
Output2,3&4 port ( IR pass-though)
12
2 3 4 5 4 4 6
34
56
HDMI input port
Connecting and operating
1) Connect the HDMI input sources into HDBaseT splitter.
2) Connect HDMI receiver over Cat5e/Cat6 cables to both the Cat5e/6 port of HDBaseT Splitter
and Cat5e/6 port of Receiver,The RJ45 connections must follow EIA-TIA 568b standards.
3) Connect the HDMI output from the Receiver(RX) into the display HDMI input.
emitter onto the source IR windows. .
5) Connect IR-RX cable into IR-RX port on the receiver and af
x the receiver on the display frame
/bezel or the display stand.
Note：Do not a x the emitter until the placement is tested.
6) Power up all units, the splitter,Receiver, sources and displays.
Output1 port ( Ethernet,RS232&IR pass-though)
Ethernet port

Operating Instructions
5
Output1
HDTVHDTVHDTV
HDMI cable
Cat5e cable
IR cable
Receiver Receiver Receiver Receiver
IR-RX
IR-RX
HDMI cable
Ethernet cable
Smart TV
Router
Internet
RS232 cable
RS-232 pin assignment
HDBaseT Splitter
PIN Assignment
1 NC
2TX
3 RX
4 NC
5 GND
6 NC
7 NC
8 NC
9
NC
7) To get on the ethernet,pls connect as below steps:
1.Connect ethernet cable into ethernet port on HDBaseT splitter.
2.Connect ethernet cable with TV and ethernet extender receiver
Note:1.The ethernet function is designed for ethernet compatible receiver units only.
2.Only output1 with ethernet function.
8) Copy EDID function
Copy the EDID of the sink which connected the OUTPUT3,it is suggested to put lowest or
For example:
One SDTV(480p) ,one HDTV(1080p), in order to make the 4 TV work, you need to put the
SDTV is connected to the output 3 .
Computer RS232 port
PIN Assignment
1 NC
2RX
3 TX
4 NC
5 GND
6 NC
7 NC
8 NC
9
NC
Front Panel
Rear Panel
Power ON/OFF
Status indicator lamp:The LED will illuminate when the HDMI equipment is connected.
Power indicator lamp:The LED will illuminate when the power is on.
Reset key
Power input port
1 3
2
4
RS232 port
Output2,3&4 port ( IR pass-though)
12
2 3 4 5 4 4 6
34
56
HDMI input port
Connecting and operating
1) Connect the HDMI input sources into HDBaseT splitter.
2) Connect HDMI receiver over Cat5e/Cat6 cables to both the Cat5e/6 port of HDBaseT Splitter
and Cat5e/6 port of Receiver,The RJ45 connections must follow EIA-TIA 568b standards.
3) Connect the HDMI output from the Receiver(RX) into the display HDMI input.
emitter onto the source IR windows. .
5) Connect IR-RX cable into IR-RX port on the receiver and af
x the receiver on the display frame
/bezel or the display stand.
Note：Do not a x the emitter until the placement is tested.
6) Power up all units, the splitter,Receiver, sources and displays.
Output1 port ( Ethernet,RS232&IR pass-though)
Ethernet port

Operating Instructions
6
RS-232 pin assignment
HDBaseT Splitter
PIN Assignment
1 NC
2TX
3 RX
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC
7) Copy EDID function
Copy the EDID of the sink which connected the OUTPUT1,it is suggested to put lowest or
For example:
One SDTV(480p) ,one HDTV(1080p), in order to make the 2 TV work, you need to put the
SDTV is connected to the output 1 .
Computer RS232 port
PIN Assignment
1 NC
2RX
3 TX
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC
2
Output1
HDTVHDTVHDTV
HDMI cable
Cat5e cable
IR cable
Receiver Receiver Receiver Receiver
IR-RX
IR-RX
HDMI cable
Ethernet cable
Smart TV
Router
Internet
RS232 cable

Operating Instructions
7
2

Operating Instructions
8
8