Shuttle PC850 Installation instructions

PRODUCT
SPECIFICATIONS
1 | 4
Shuttle Computer Handels GmbH · Fritz-Strassmann-Str. 5 · 25337 Elmshorn · Germany
Tel. [phone] · Fax [phone] · [email protected]
WWW.SHUTTLE.EU
ACCESSORY
Power Supply Kit
PC850
UNIVERSAL
WLAN
-
AX/BLUETOOTH
KIT
WITH
M.2
CARD
The Shuttle XPC Accessory PC850 is an internal AC to DC switching power supply unit
(PSU) meant as upgrade kit for certain Shuttle products. This power supply is guaranteed
to deliver an excess of power for power-hungry processors and graphics cards. It provides
a maximum output wattage of 850 Watt. Its 80 PLUS® Platinum and Energy Star V5.0
compliance helps save on energy costs as compared to previous power supply models.
COMPATIBILITY
Compatible with the following Shuttle XPCs in cube form factor:
◼ SH510R4 ◼ SH570R6 (Plus) ◼ SH570R8 ◼ SW580R8
◼ SH310R4V2 with Serial No. SH310V20501...
◼ SH370R6V2 with Serial No. SH370V20801...
◼ SH370R6V2 Plus with Serial No. SH370V20901...
◼ SH370R8 with Serial No. SH370R80701...
PACKAGE CONTENTS
◼ Internal power supply (850 W)
◼ angle holder with screw
◼ Quick guide
AC INPUT
◼ Input voltage: 100 - 240 V AC (auto-adjust), 50 - 60 Hz
◼ Input current: max. 10.0 - 6.0 A
◼ Active Power Factor Correction (PFC) meet EN61000-3-2
◼ AC Input Connector: Cold-device plug, 3-pin with PE (IEC-60320/C14)
DC OUTPUT VOLTAGES
◼ Output voltage (max. output current):
+3.3V (20A), +5V (20A), +12V (70.8A), -12V (0.5A), +5Vsb (3A)
◼ Low ripple: 120 mV P-P for 12V and 50 mV P-P for 3.3/5V
◼ Rise time: less than 20ms
◼ Hold-up Time: 17 ms minimum at nominal input voltage for 75% maxi-
mum load
◼ Power Good Signal: Power on delay time 100 ~ 500ms, off delay 1ms
minimum (TTL and CMOS compatible)
◼ Leakage Current: Less than 3.5mA at 264Vac, 63Hz
MAXIMUM OUTPUT POWER
◼ +3.3V and +5V combined power: max. 100 W
◼ Total power output: max. 850 W
DC OUTPUT CONNECTORS
◼ 1x main mainboard connector (20-pin ATX)
◼ 1x mainboard AUX connector (4-pin ATX 12V)
◼ 4x Serial ATA power connectors (15-pin SATA)
◼ 2x PCIe power with 6+2 pins (for graphics card)
◼ 2x 4-pin WST connector with 12V (reserved)
◼
1x PMBus data cable, 5-pin (reserved)
COOLING FANS
40 mm ball-bearing fan at output side for better acoustic quality
LED Indicator
LED off/blinks/green/red: Off/Standby/Ok/Failure
DIMENSIONS
220 x 81.5 x 40.5 mm (LWH), Flex ATX form factor
HIGH RELIABILITY
◼ MTBF: 100,000 hours at 25 °C, max. output load
◼ Short circuit protection on all outputs
◼ Over Current Protection (OCP)
◼ Over Temperature Protection (OTP)
◼ Over Voltage Protection (OVP)
◼ Dielectric Withstand: Primary frame ground 1800V AC for 2 second
EFFICIENCY
Typical > 92% Efficiency, meets 80 Plus Platinum criteria
90% / 92% / 89% at 20% / 50% / 100% PSU load
ENVIRONMENTAL CRITERIA
◼ Operating: 0 to 50 °C, max. 90% RH non-condensing
◼ Storage: -20 to 80 °C, max. 90% RH non-condensing
◼ Operating altitude: max. 5,000 meters above sealevel
COMLIANCE AND LOGOS
CE, TUV, FCC, UL/cUL, CCC, CB 62368-1 & CB 60950-1
Energy Star 5.0 & ErP, 80 PLUS® Platinum
PSU MANUFACTURER
Fortron Source Technology (FSP Group),
Product ID of manufacturer: FSP850-50FGPH3
(with modified cable lengths and number of connectors)

PRODUCT
SPECIFICATIONS
2 | 4
Shuttle Computer Handels GmbH · Fritz-Strassmann-Str. 5 · 25337 Elmshorn · Germany
Tel. [phone] · Fax [phone] · [email protected]
WWW.SHUTTLE.EU
Caution: Do not attempt to open or service this device. Changes or modifications done to this product not approved by the manufacturer will void war-
ranty and violate CE approval. In case you haven't got necessary technical knowledge how to install the device, please consult an expert or have a speci-
alist company install it for you.
Removing the old power supply unit
Unplug the computer from the mains.
Unscrew 3 thumbscrews of the chassis cover (see photo).
S
lide the
cover backwards and upwards
.
Unscrew the screws that are used to secure the power supply unit to
the the computer chassis.
Quick Installation Guide

PRODUCT
SPECIFICATIONS
3 | 4
Shuttle Computer Handels GmbH · Fritz-Strassmann-Str. 5 · 25337 Elmshorn · Germany
Tel. [phone] · Fax [phone] · [email protected]
WWW.SHUTTLE.EU
Disconnect all connections between the old power supply unit and the
various components such as the mainboard, the hard drive and graphics
card, etc.
Then carefully remove the power supply unit.
Installing the new power supply unit
Pick up the new PC
850 power supply and install the supplied
angle hol-
der with a screw. Use the screw from the angle holder of the previous
power supply unit for this purpose.
Push the cables of the power supply through the internal housing ope-
ning as shown in the picture.

PRODUCT
SPECIFICATIONS
4 | 4
Shuttle Computer Handels GmbH · Fritz-Strassmann-Str. 5 · 25337 Elmshorn · Germany
Tel. [phone] · Fax [phone] · [email protected]
WWW.SHUTTLE.EU
© 2022 Shuttle® Computer Handels-GmbH — All information subject to change without notice. Optional components and accessories are not included. Pictures for illustration purposes only.
Fasten the power supply unit to the rear panel with three screws and to
the mounting bracket with the supplied screw (see arrow).
Connect the two ATX connectors (20
-
pin and 4
-
pin) to the motherboard
and proceed with the installation as described in the Shuttle XPC instal-
lation guide.