Si Tech 11920 User manual

Document produced by
Johanna Strömgren
2012-03-12
Pee Valve
11920/11925
11920 Pee Valve set with Tool and Valve Port (A, B and C)
11925 Pee Valve complete set (A, B, C, D and E)
Parts list
A Pee Valve 1 pcs
B Disassembly Tool (item no. 18417B) 1 pcs
C Valve Port (item no. 60895) 1 pcs
D Blanking plug (item no. 60340) 1 pcs
E Uridome 30 mm (item no. 11908) 2 pcs
Extra Uridomes
• 25 mm (item no. 11907)
• 30 mm (item no. 11908)
• 35 mm (item no. 11909)
SI TECH AB | Phone: [phone] | [email protected] | www.sitech.com
Visiting address: Tuntorp 154 | 454 93 Brastad | Sweden
C
E
A
D
B
Put on the rest of the undergarment. Don the suit as far as the thighs and attach
the silicone hose to the attachment nut socket. Complete donning the suit.
Using
Push the lid down and turn to close (off) and turn top open (on). When using,
turn the valve open and then urinate.
Note! The valve should be open in water - expanding air is relieved through the
valve. Do not wait too long before relieving yourself. Urinating often is better. To
minimize the pressure difference, maintain a horizontal position while urinating.
Doffing
Turn the Pee Valve open. Open the suit and undergarment. Squeeze as much
urine as possible out of the hose, from the uridome and outwards, through the
valve.
Disconnect the hose from the attachment nut socket. If possible, cover the socket
to avoid further spill/leakage. After doffing the suit; remove the dump valve, rinse
it and insert the blanking plug (if available).
Use the disassembly tool to clean the valve.
Turn counter clockwise to disassemble the
top lid from valve body.
Wash the entire valve with luke warm soapy
water and rinse thoroughly with warm
water.
Store the valve open (turned off) and dis-
connected from the hose. Uridomes are
preferably used once only.

The hole in the fabric has to be bigger than
usual (a minimum diameter is 55,5 mm). This
method of connection must be used.
Otherwise, the connection between the valve
and the attachment nut will be insufficient or
impossible.
Assembly of hose and uridome
To ease the insertion, angle cut the silicone
hose >45 degrees. Insert the chamfered end
through the uridome extension.
To secure the hose from slipping out; apply
silicone sealant or Aquasure on the last 30
mm of the hose. Pull the rest of the hose,
until it does not protrude, into the cup of the
uridome.
Adjust the length of the hose (still allowing
you to stretch your legs when swimming).
Cut the end perpendicular.
Donning
Relieve yourself before donning the suit. The
uridome is put on the same way as a condom.
Make sure no hair is snagging in the self
adhesive surface.
Put on the undergarment as far as the thighs
and put the end of the hose through the
hole.
Gently taping the hose to the body is a good idea. Make sure sharp bends and
any potential squeeze of the hose are avoided.
www.SITECH.se
The SI TECH Pee Valve is intended for attachment in a Valve Port that is
permanently glued to the suit. Recommendations on adhesive types,
solvents and installation to the suit material must come from your suit
manufacturer or an authorized suit repair facility. The Pee Valve is fur-
nished with a pressure compensation checkvalve inside the internal nut.
On/Off valve for easy manoever.
Twin Check Valves for safe
evacuation and no outer leakage.
Pressure compensated.
Easy to clean. Disassembly tool is
included.
Top lid
Valve body
Valve Port
Attachment nut
Socket
Hose
Disassembly tool
Valve Port to be glued to the suit.
Suit preparations
Attach the valve into the suit on the upper
and inner part of the thigh (minimum 15
mm from the crotch), easily accessible when
turning dump valve on and off. (A blanking
plug (60340) is required when the Pee Valve
is not in use.)
Attach the Pee Valve into the Valve Port with
the socket of the attachment nut pointing upwards.
The undergarment also needs to be penetrated (i.e. on the thigh) to give way for
the hose. To keep the parts on the inside of the suit as low as possible, the attach-
ment nut is designed to be fitted against the Valve Port directly. No suit material
can remain between the connecting nut and the Valve Port.
minimum
diameter
55,5 mm