Siemens HG193510ME User manual

Installation instructions
Instructions for use
HG193510ME
HG195510ME
HG196510ME
HG197510ME
HG198210ME
HG198510ME
HG199210ME
HG199510ME
EN

...........

1
Installation instructions 1-22 | Instructions for use 23-90
Installation instructions
Safety precautions ___________________________________________ 3
Before installing _____________________________________________ 4
Appliance........................................................................................................ 4
Guideline for ventilation.................................................................................. 6
Installation __________________________________________________ 7
Fitting the adjustable feet ............................................................................... 7
Fitting the splash guard .................................................................................. 8
Electrical connection _________________________________________ 9
Gas connection _____________________________________________ 11
Converting the gas type ______________________________________ 15
Hotplate burners........................................................................................... 15
Oven burner ................................................................................................. 17
Grill burner.................................................................................................... 20
General nozzle table .................................................................................... 21
Positioning and levelling _____________________________________ 22

2

3
Safety precautions
This manual is valid for several models. Variations in
details for each cooker are possible.
The safe operation of this appliance can only be
guaranteed if it has been professionally assembled
and installed in accordance with these instructions.
The individual who assembled and installed the
appliance is liable for damage or faults resulting from
incorrect assembly or installation.
All installation and adjustment work, as well as the
conversion to a different type of gas must be
undertaken by an authorised expert and carried out in
accordance with the currently applicable rules and
regulations of the local gas and electricity supply
company.
Shut off the supply of electricity and gas before
carrying out any work.
Before installing the appliance, check that the local
conditions (type of gas and pressure) are compatible
with the appliance settings. The permissible
appliance settings can be found on the rating plate.
Electrical appliances must always be earthed.
If an extractor hood is to be fitted, it must be fitted
according to the associated assembly instructions.
Ensure that the hood is fitted at least 650 mm clear of
the hob.

4
Before installing
Read the following information about the appliance
and the guidelines for ventilation.
Appliance
Unpacking Check the condition of the appliance after unpacking
it. Do not connect the appliance if it has been
damaged in transport.
Dispose of packaging in an environmentally-friendly
manner.
The appliance is bolted to the pallet with two bolts.
To release the appliance, proceed as follows:
• Undo the bolts on the rear of the appliance.
• Screw the bolts back into the appliance without
the connecting brackets.
Appliance class This appliance corresponds to the following
appliance classes:
Appliance class Description
Class 1
Non flush-fitted cooker
Class 2 - subclass 1
Cooker immediately adjacent to two
units, consisting of a single unit.
Can also be installed so that the
side walls are accessible.

5
Appliance dimensions Note the specified dimensions.
Adjacent units Adjacent units must be made of non-combustible
material. The fronts of adjacent units must be
resistant to temperatures up to at least 90 °C. If the
appliance is fitted close to other units, the minimum
distances specified in the picture must be maintained.
HG195510ME
A = 95-160 mm
(HG193510ME, HG197510ME, HG198210ME,
HG199210ME: A= 90-145 mm)
B = 820-885 mm
(HG193510ME, HG197510ME, HG198210ME,
HG199210ME: B= 815-870 mm)
HG193510ME, HG196510ME, HG197510ME,
HG198210ME, HG198510ME, HG199210ME,
HG199510ME

6
Rating plate The technical data for the appliance can be found on
the rating plate on the inside of the storage
compartment flap.
Never remove the rating plate from the appliance.
The setting values are specified on a label on the
appliance packaging.
Use the table below to record the product number (E
no.),
production number (FD no.),
factory setting for type of gas and pressure and
if applicable, the type of gas and pressure
conversions.
Guideline for ventilation
This appliance may only be set up in a sufficiently
ventilated room and according to the applicable
regulations and ventilation requirements.
Please note that the air volume required for
combustion must not be below 2 m3/h per kW of
power (see kW total power on the rating plate).
E no. FD no.
After-sales service
Type of gas
Gas pressure
(factory setting)
Type of gas
Gas pressure
(conversion)

7
Installation
This appliance is always supplied with a set of
adjustable feet and, depending on the model, with a
splash guard.
The appliance may also be used without the splash
guard.
Fitting the adjustable feet
Beforehand:
• Remove all parts that are not permanently fixed,
especially the pan supports and burners.
• Remove the accessories from the oven.
Proceed as follows:
• Tilt the appliance by raising one side slightly from
the floor.
• With the plates in position, screw the adjustable
feet into the mounting holes on the underneath of
the appliance.
• Repeat the process on the other side.
You can make the final adjustments to the feet in
order to level the appliance once the gas and
electricity supply have been connected.
If it is necessary to pull the appliance, screw the
adjustable feet in fully. Make the final settings only
when the other installation tasks have been
completed.

8
Fitting the splash guard
Depending on the model.
Proceed as follows:
• Remove the packaging and the protective film
from the splash guard.
• Screw the splash guard onto the rear of the
appliance using the 2 bolts, each with a washer,
retaining washer and nut.