Siemens Sitraffic Sensus Unit C3077 User manual

Sitraffic Sensus Unit
Instruction Manual
Instruction Manual
Edition: 06 / 2016
Sitraffic Sensus Unit C3077
C97158-C3077-C148-01-N9

2© Siemens Aktiengesellschaft Österreich© Siemens Aktiengesellschaft Österreich

















© Siemens Aktiengesellschaft Österreich 3© Siemens Aktiengesellschaft Österreich

8
Permanent power supply cable with intermediate connector* Fuses not included
Vehicle electrical system
8 – 32V red: constant voltage +
black: ignition
brown: ground –
9

4© Siemens Aktiengesellschaft Österreich© Siemens Aktiengesellschaft Österreich

 

 

 


 
3
TEXT AB-0123
HU-GO
TEXT AB-0123
HU-GO
2
TEXT AB-0123
HU-GO
2
TEXT AB-0123
HU-GO
14



 
TEXT AB-0123
HU-GO
2
10 11

Display icons Description
Displays availability of GSM
Displays availability of GPS
HU-GO HU-GO
HU-GO: activated / temporarily disabled
Sitraffic Sensus Unit connected to the external power supply and battery charging
Sitraffic Sensus Unit operated from the battery
Sitraffic Sensus Unit operated from the battery and the battery is low (symbol is blinking)
USB correctly connected
USB correctly connected but connection to electronic toll operator failed
Defect
Commercial lock
Battery missing/ defect
Transport mode
© Siemens Aktiengesellschaft Österreich 5

6© Siemens Aktiengesellschaft Österreich
Imprint Sitraffic Sensus Unit
Instruction Manual
Information related to the content of the instruction manual
This manual reflects the state as at the time of downloading. Please check from time
to time if an updated version is available on web page
www.siemens.com/mobility-
sensusunit-manuals .
Siemens Aktiengesellschaft Österreich (“Siemens“) reserves the right to make changes
to specifications, descriptions, operation instructions and figures in this manual.
This manual does not contain nor regulate the vehicle operator/driver rights and
obligations related to electronic toll collection stipulated by the relevant legal acts.
This manual is subject to the copyright of Siemens. No part of this manual may be
reproduced in any manner without the prior express approval of Siemens.
Disclaimer
Intended use of Sitraffic Sensus Unit is the electronic toll collection and other telematic
services, if not explicitly stated otherwise. Siemens shall not be held liable for any
damages caused by non intended or any improper use of the Sitraffic Sensus Unit,
especially any personal injury, any damage at property or any financial loss.

Sitraffic Sensus Unit
Instruction Manual
7© Siemens Aktiengesellschaft Österreich
Contents
1 Symbols used in this manual................................................................................... 8
2 Notes on safety ...................................................................................................... 8
3 Intended use .......................................................................................................... 8
4 General instructions ............................................................................................... 9
5 Verifying the Sitraffic Sensus Unit package contents ............................................. 10
6 Installation types .................................................................................................. 10
7 Installation in vehicles transporting dangerous goods (ADR vehicles) ........................ 11
8 Mounting and installing the Sitraffic Sensus Unit .................................................. 11
9 User interface ...................................................................................................... 14
10 Operation ............................................................................................................ 15
11 Removal ............................................................................................................... 21
12 Available accessories ............................................................................................ 22
13 Permanent installation ......................................................................................... 22
14 Technical data ...................................................................................................... 24
15 Declaration of conformity ..................................................................................... 25
Contents

© Siemens Aktiengesellschaft Österreich8
Sitraffic Sensus Unit
Instruction Manual
1 Symbols used in this manual
2 Notes on safety
3 Intended use
Danger of accident!
Do not handle the Sitraffic
Sensus Unit while driving.
Danger of fire!
A damaged power supply
cable can cause fire by
short circuits.
Replace
damaged power supply
cables immediately!
1 Symbols used in this manual / 2 Notes on safety / 3 Intended use
Danger
Symbol and words refer to
dangerous situations which
could lead to serious injury or
death.
Caution
Symbol and words refer to
dangerous situations which
could lead to damage of the
device or other property.
Remark
Symbol and words refer to
additional information which
you should pay attention to.
Reference
The number in the symbol
refers to the related figure
at the beginning of this
manual.
The Sitraffic Sensus Unit is intended to be used for electronic toll collection
and other telematic services, if not explicitly stated otherwise, and may
only be used for this purpose. Any other use is considered to be a prohibited
misuse and would result in the denial of any claims.

Sitraffic Sensus Unit
Instruction Manual
9© Siemens Aktiengesellschaft Österreich
4 General instructions
4 General instructions
Destruction caused by over-voltage!
The Sitraffic Sensus Unit is designed for a voltage range of 8 – 32 V DC and
must therefore not be used outside this voltage range. If your on-board
network can generate higher voltages (e.g. jump-starting from an external
power source or from additional stronger power generators in the vehicle),
then you must disconnect the unit from the on-board network for the
duration of the over-voltage.
Damage caused by incorrect cleaning!
The unit may be cleaned when required with a damp cloth. Do not use any
volatile solvents, e.g. alcohol and do not use abrasive cleaning agents.
Damage caused by incorrect handling!
The Sitraffic Sensus Unit is an electronic device and therefore you should
avoid excessive impact forces. Do not operate the unit with pointed or sharp
objects.

© Siemens Aktiengesellschaft Österreich10
Sitraffic Sensus Unit
Instruction Manual
5 Verifying the Sitraffic Sensus Unit package contents /
6 Installation types
There are two possible installation types:
• Temporary installation – In this case the Sitraffic Sensus Unit is powered from the
cigarette lighter socket.
• Permanent installation – In this case the Sitraffic Sensus Unit is connected to
the vehicle electrical system by an optional available power supply cable with
intermediate connector.
This manual describes both installation types which can be used alternatively depending
on the available accessories. The permanent installation will be described in chapter 13.
The Sitraffic Sensus Unit package contains:
1. One Sitraffic Sensus Unit including rechargeable battery
2. One power supply cable for cigarette lighter installation, with LED power supply
indication on the connector
3. One plastic bag including holder and one cleaning cloth
4. Three sucction cups
5. One Installation and Safety Instructions leaflet (for once may be handed out
seperately).
Please check if the package content is complete and undamaged. If you find so-
mething missing or damaged, please claim at after-sales service of your operating
company immediately!
6Installation types
5 Verifying the Sitraffic Sensus Unit package
contents

Sitraffic Sensus Unit
Instruction Manual
11© Siemens Aktiengesellschaft Österreich
Mounting the suction cups to the holder
Attach the provided suction cups to the holder as shown in the related figure.
Connecting the power cable to the Sitraffic Sensus Unit
1. Remove the connector panel cover of the device.
2. Plug the provided power supply cable into the power socket and make sure
that the plug’s snap catch has engaged.
3. Make sure that the rubber tube of the provided power supply cable is located
at the right position.
4. Close the device again with the connector panel cover.
7 Installation in vehicles transporting dangerous goods (ADR vehicles) /
8 Mounting and installing the Sitraffic Sensus Unit
8 Mounting and installing the Sitraffic Sensus Unit
Danger of explosion! Installation in ADR vehicle is a case for fixed installation
and must only be performed by authorised staff! If you wish to install the
device into an ADR vehicle please contact the after-sales service of your
operating company for support.
7 Installation in vehicles transporting
dangerous goods (ADR vehicles)
Danger of fire and malfunction!
Always protect the power supply cable against mechanical forces and other
negative factors (e.g. extensive heat, aggressive chemicals) which could
lead to destruction of isolation and short circuits.
Replace damaged cables immediately!.

© Siemens Aktiengesellschaft Österreich12
Sitraffic Sensus Unit
Instruction Manual
Determine the Sitraffic Sensus Unit mounting location
Determine the mounting location on the inside of the windscreen such that:
• the driver‘s field of vision is not impaired while driving,
• the chosen position must not be near moving parts e.g. air bag covers of the
vehicle,
• the Sitraffic Sensus Unit is visible from outside and is not hidden by other
elements such as windscreen wipers when off,
• the Sitraffic Sensus Unit does not constrain the function of the defroster vents,
• in the case of metalized windscreen use non-metalized area,
• local laws and regulations as well as recommendations of the vehicle manufac-
turer are complied with.
In case of doubts please contact the after-sales service of your operating company for
support.
Danger of accident!
Always mount the Sitraffic Sensus Unit in such way that driver‘s field of vision is
not impaired!
Attaching the holder to the windscreen
1. The determined location on the windscreen and the contact surface of the
suction cups must be clean, dry and free from oil and grease. If necessary,
carefully clean with the supplied cleaning cloth and wait until the surface is dry
before to proceed with the next step.
2. Attach the holder at the chosen position with the suction cups. Press firmly at
the centre of each suction cup.
When using the suction cups you must check for correct fitting before each jour-
ney.
The service life of the suction cups is typically 6 months if the suction cups are
used on the windscreen.
8 Mounting and installing the Sitraffic Sensus Unit

Sitraffic Sensus Unit
Instruction Manual
13© Siemens Aktiengesellschaft Österreich
Assembling the device and its holder
1. Close the gap between the Sitraffic Sensus Unit and holder until you hear a
clicking sound.
2. Check the connection by trying to tear apart the holder and the Sitraffic Sensus
Unit.
Connecting the Sitraffic Sensus Unit to the external power supply
Connect the Sitraffic Sensus Unit power supply cable for temporary installation to
the cigarette lighter socket (or DIN socket) as shown in the figure.
It is recommended to use the DIN socket to plug in the cigarette lighter connector of the
power cable. The DIN socket in the vehicle is recognizable by the smaller diameter of the
socket compared to a conventional one. To use this socket you have to remove the red cap of
the connector by twisting it to the left. Then plug the cigarette lighter connector into the DIN
socket.
Don’t remove the red cap if you use a conventional cigarette lighter socket. You can
immediately plug the cigarette lighter connector into the cigarette lighter socket.
The Sitraffic Sensus Unit may only be connected to voltages of
between 8 and 32 V DC. Ignoring this warning could lead to serious
damages of the device and will cause a decline of guarantee claims.
Fix the power supply cable in such a way that it cannot become
disconnected while driving the vehicle or otherwise negatively affects
the vehicle operation.
8 Mounting and installing the Sitraffic Sensus Unit
6

© Siemens Aktiengesellschaft Österreich14
Sitraffic Sensus Unit
Instruction Manual
9 User interface
The Sitraffic Sensus Unit informs you through its user interface permanently about its
status, provides the means for all necessary settings and gives you the feed back to user
interaction.
User interface comprises the following elements:
1. Display – for displaying of the operational status and settings.
2. Four direction navigation button – for:
– setting of the axles number
– enabling or disabling of acoustic signalization
– forcing communication with central system.
3. Overall status LED – for indication of overall Sitraffic Sensus Unit status.
4. Beeper – for acoustic:
– signalization of performed actions
– feedback to user interactions
– signalization of number of axles on startup.
9 User interface

Status LED
Four direction
navigation button
Display

Sitraffic Sensus Unit
Instruction Manual
15© Siemens Aktiengesellschaft Österreich
10 Operation
10
Danger of accident!
Do not try to handle the Sitraffic Sensus Unit while driving.
Switching on the Sitraffic Sensus Unit
The Sitraffic Sensus Unit does not have a power on or off switch. By connecting the
Sitraffic Sensus Unit to the power supply it starts to operate and shows the battery
symbol in the upper right of the display. In case the Sitraffic Sensus Unit is already
connected it starts:
• when the ignition is turned on or
• when the vehicle starts to move.
Sitraffic Sensus Unit in operation
1Number of axles
2 Activated toll services
3 Status LED
4 Licence plate number
5 Connection to external power supply
6 Battery status
Selecting the number of axles
Before starting a trip on the tollable road network you have to set the proper
number of axles, if it differs from initial declaration. The initial configuration
and activation of the device is done by the after-sales service of your operating
company.
Please check if the information shown on the display is correct (e.g. license plate
number, number of axles).
At the beginning of this manual you can find an overview of changing the number
of axles (2, 3, ... 14 axles), whereas the settings have to be chosen according to the
legislation in force. Please contact the after-sales service of your operating company
for further information.

 
  






TEXT AB-0123
HU-GO
10 Operation
8

© Siemens Aktiengesellschaft Österreich16
Sitraffic Sensus Unit
Instruction Manual
10 Operation
Use the navigation key and long press “
B
” or “B” repeatedly, until the number of axles in
the symbol matches to your vehicle (or semi-trailer unit). The number of axles within the
lorry symbol and the status LED are blinking (the latter in yellow) until a confirmation is
sent by the back office.
On receipt of acknowledgement, the selected number of axles within the lorry symbol
turns stable and the LED shows permanently green.Thus the correct settings of the num-
ber of axles are enabled in the Sitraffic Sensus Unit.
This process can take a while and you may choose to get in contact with the after-
sales service of the operating company to notify the axle change using a different
methodology (e.g. SMS).
In case HU-GO is activated, the status LED is green and the correct number of axles set, the
Sitraffic Sensus Unit is ready for use in the HU-GO toll domain.
Enabling / Disabling of acoustic signalization
The Sitraffic Sensus Unit has an integrated speaker where some of the acoustic signals can
be switched off (see table “acoustic signalization“).
Use the navigation key and press “▼” or “▲” until the speaker symbol appears.
Use the navigation key and press “
B
“ or “B” to enable or disable the speaker.
Display of information screen
The Sitraffic Sensus Unit offers the possibillity to display information about the used version.
Use the navigation key and press “▼” or “▲” until the information symbol appears.
Use the navigation key and press “B” to display the information about the version,
press “▼” or “▲” for further information.
After accomplishing your selection you can change to the normal operation screen by
pressing twice “
B
“, respectively the screen turns automatically to the normal operations
screen after some time.
Battery and connection to external power supply status
The normal operations mode requires the Sitraffic Sensus Unit to be connected to vehic-
les power supply. Nevertheless the Sitraffic Sensus Unit has an integrated battery that
keeps the Sitraffic Sensus Unit operational even during short power outages of the vehicle.
The display informs you about the operation status of the battery and an arrow in front of
battery symbol indicates connection to the external power supply:
11
11

Sitraffic Sensus Unit
Instruction Manual
17© Siemens Aktiengesellschaft Österreich
10 Operation
Sitraffic Sensus Unit connected to the external power supply and battery
charging
Sitraffic Sensus Unit connected to the external power supply and battery
defect or missing
Sitraffic Sensus Unit operated from the battery
Sitraffic Sensus Unit operated from the battery and the battery is low
(symbol is blinking)
When Sitraffic Sensus Unit is disconnected from external power supply, it indicates this
fact additionally to display also by status LED and acoustically. In this case status LED
is periodically after 5 minutes switched off for 5 seconds and every 5 minutes Sitraffic
Sensus Unit beeps shortly. When battery reaches low level, status LED change interval for
cyclic changes to 5 seconds off and 10 seconds on.
In the case that Sitraffic Sensus Unit indicates operation from the battery, check the
power supply cable and fuse in connector and try to reestablish the power supply.
Activation of toll services
Toll services HU-GO will be activated by your operating company as part of the handover.
Forcing a transmission
You may be required to force the Sitraffic Sensus Unit to transmit data (on request). For
this procedure please press on the navigation button “▲” for more than 2 seconds, until
you hear a double beep from the speaker confirming the acceptance of the procedure.
You will see in the left down corner of the display the connection attempt and get back
the result of communication.
Displaying of connection attempt
Transmission successful
Transmission failed

© Siemens Aktiengesellschaft Österreich18
Sitraffic Sensus Unit
Instruction Manual
10 Operation
Operational
status Status LED Display Description
ACTIVE
Green
This is the normal operation state of the HU-GO service.
In the middle of the display the selected number of
axles is shown.
WARNING
Yellow blinking
A yellow blinking status LED indicates, that the Sitraffic
Sensus Unit is in warning state, currently not ready for
HU-GO tolling, e.g. no GPS.
DEFECT
or
COMMERCIAL
LOCK
Red
in the middle
of the display
If the Sitraffic Sensus Unit is not ready for use this
is indicated by a warning triangle in case of a
technical defect or a lock symbol in case of a
commercial lock in the middle of the display.
If the status LED is red, the Sitraffic Sensus Unit is not ready to use and you are
not allowed to use the HU-GO road network. In this case contact immediately the
after-sales service of your operating company.
If the status LED is blinking yellow, the Sitraffic Sensus Unit is in warning state,
currently not ready for HU-GO tolling, e.g. no GPS.
Sitraffic Sensus Unit operational status
or

Sitraffic Sensus Unit
Instruction Manual
19© Siemens Aktiengesellschaft Österreich
10 Operation
Transport mode
Transport mode is used when transportation of the Sitraffic Sensus Unit is needed without
charging for usage of the tolled road network. It can be enabled in conjunction with the
handover procedure or on request by calling the after-sales service of your operating
company. This mode is indicated by the following symbol shown in the right down corner
of the display and becomes active after disconnect from power supply.
Sitraffic Sensus Unit update
The Sitraffic Sensus Unit may require software updates which are distributed
remotely automatically. During start up the Sitraffic Sensus Unit may exe-
cute this procedure, showing the progress on the display. Wait until update
procedure is completed. After the update is completed the Sitraffic Sensus
Unit returns to normal operation mode.
Acoustic signalization
The Sitraffic Sensus Unit is designed to give you acoustic notification (in case the speaker
operation is enabled) for events that may occur during operation of the Sitraffic Sensus Unit.
Event Tone Repetition Configurable
Startup – at least one toll
service activated
No. of axles 1 x no
Startup w/o any toll
service activated
1 ×
Shutdown 1 x

© Siemens Aktiengesellschaft Österreich20
Sitraffic Sensus Unit
Instruction Manual
10 Operation
Event Tone Repetition Configurable
Activation 1 x
External power disconnected (more
than 20 minutes operation possible)
every 5 minutes no
Battery low (less than 20 minutes
operation possible)
every 5 minutes no
External power reconnected 1 ×
GPS currently not available or
operating temperature range
exceeded or geodata expired
every 60 seconds
Commercial locked or
Defect
every 15 seconds
Fatal error 1 × no
Key pressed 1 ×
Invalid key press 1 ×
Axles change No. of axles 1 ×
Speaker ON 1 × no
Speaker OFF 1 × no
Successful data
transmission confirmation
1 ×
No. of axles Tone Repetition Configurable
1 × no
1 × no
1 × no
2, 3 or 4 axles , or
5, 6, ... 9 axles , ...
10, 11, ... 14 axles , ...