Siemens SIMATIC ET 200S M151-3 PN User manual

Interface module
IM151-3 PN HIGH FEATURE (6ES7151-
3BA23- 
0AB0)
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
SIMATIC
ET 200S distributed I/O
Interface module
IM151-3 PN HIGH FEATURE
(6ES7151-3BA23-0AB0)
Manual
08/2010
A5E01584258-04
Preface
Properties
1
Parameters
2
Functions
3
Interrupt, error, and system
messages
4
Response times
5

Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E01584258-04
Ⓟ 09/2010
Copyright © Siemens AG 2010.
Technical data subject to change

Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 3
Preface
Preface
Purpose of the manual
This manual supplements the ET 200S Distributed I/O System Operating Instructions.
Functions that apply generally to the ET 200S are described in the ET 200S distributed I/O
system (http://support.automation.siemens.com/WW/view/en/1144348) operating
instructions.
The information in this document along with the operating instructions enables you to
commission the ET 200S.
Required basic knowledge
To understand these operating instructions you should have general knowledge of
automation engineering.
Scope of the manual
The manual applies to this ET 200S module. It describes the components that are valid at
the time of publication.
The manual is valid for the IM151-3 PN HIGH FEATURE ((6ES7151-3BA23-0AB0)) firmware
version V7.0 and higher.
Changes since the previous version
The following changes have been implemented compared to the
IM151-3 PN HIGH FEATURE(6ES7151-3BA23-0AB0) Manual, Edition 03/2009, with the
number A5E01584256-02:
● Shared Device
● Media redundancy
● Option handling
● LED display of the configuration and parameter assignment errors
● PROFIenergy
Recycling and disposal
Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For
environmentally compliant recycling and disposal of your electronic waste, contact a
company certified for the disposal of electronic waste.

Preface
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
4 Manual, 08/2010, A5E01584258-04
Additional support
If you have any questions relating to the products described in this manual and do not find
the answers in this document, please contact your local Siemens representative.
Your contact persons are listed in the Internet (http://www.siemens.com/automation/partner).
A guide to the technical documentation for the various SIMATIC products and systems is
available in the Internet (http://www.siemens.com/simatic-tech-doku-portal).
The online catalog and ordering systems are available in the Internet
(http://mall.automation.siemens.com).
Training center
Siemens offers a series of courses that will help you getting started with ET 200S and the
SIMATIC S7 automation system. Please contact your regional training center or the central
training center in D -90327, Nuremberg, Germany.
You will find more information in the Internet (http://www.sitrain.com).
Technical Support
You can contact Technical Support for all Industry Automation products by means of the
Internet Web form (http://www.siemens.com/automation/support-request) for the Support
Request.
Additional information about Siemens Technical Support is available on the Internet
(http://www.siemens.com/automation/service).
Service & Support on the Internet
In addition to our documentation, we offer a comprehensive knowledge base on the Internet
(http://www.siemens.com/automation/service&support).
There you will find:
● Our Newsletter, which constantly provides you with the latest information about your
products.
● The right documentation for you using our Service & Support search engine.
● The bulletin board, a worldwide knowledge exchange for users and experts.
● Your local contact for Automation & Drives in our contact database.
● Information about on-site services, repairs, spare parts, and lots more.

Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 5
Table of contents
Preface ...................................................................................................................................................... 3
1 Properties .................................................................................................................................................. 7
1.1 IM 151-3 PN HIGH FEATURE interface module ...........................................................................7
1.2 SNMP...........................................................................................................................................14
1.3 SIMATIC Micro Memory Card......................................................................................................15
1.4 Firmware update ..........................................................................................................................17
2 Parameters.............................................................................................................................................. 19
2.1 Parameters for the IM151-3 HIGH FEATURE interface module .................................................19
2.2 Parameter description..................................................................................................................19
2.2.1 Bus length ....................................................................................................................................19
2.2.2 Interference frequency suppression ............................................................................................19
2.2.3 Reference junction slot ................................................................................................................20
2.2.4 Reference junction input ..............................................................................................................20
2.2.5 Release option handling ..............................................................................................................20
3 Functions................................................................................................................................................. 21
3.1 Identification data for PROFINET IO ...........................................................................................21
3.2 Configuring port 1 and port 2 .......................................................................................................23
3.3 Option handling............................................................................................................................23
3.3.1 Option handling and control data record......................................................................................23
3.3.2 Feedback data record..................................................................................................................26
3.3.3 Option handling when using RESERVE modules........................................................................27
3.3.4 Option handling without reserve modules....................................................................................29
3.3.5 Adding options .............................................................................................................................31
3.3.6 Option handling and combining procedures ................................................................................33
3.4 PROFIenergy ...............................................................................................................................35
4 Interrupt, error, and system messages .................................................................................................... 41
4.1 Diagnostics using LED display.....................................................................................................41
4.2 Diagnostic messages of the electronic modules..........................................................................45
4.3 Substitute value behavior.............................................................................................................46
4.4 Diagnostics...................................................................................................................................47
4.4.1 Diagnostics readout .....................................................................................................................47
4.4.2 Channel diagnostics.....................................................................................................................48
4.4.3 Incorrect module configurations of ET 200S on the PROFINET IO ............................................50
4.4.4 Interruption of the ET 200S backplane bus .................................................................................50
4.4.5 Failure of the load voltage from the power module......................................................................51
4.4.6 STOP of the IO controller and recovery of the IO device ............................................................51
4.5 Maintenance alarms.....................................................................................................................52
4.6 Evaluating the interrupts of the ET 200S.....................................................................................53

Table of contents
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
6 Manual, 08/2010, A5E01584258-04
5 Response times....................................................................................................................................... 55
5.1 Response times of PROFINET IO ..............................................................................................55
5.2 Response time for digital input modules..................................................................................... 55
5.3 Response time for digital output modules...................................................................................56
5.4 Response time for analog input modules.................................................................................... 56
5.5 Reaction times of analog output modules................................................................................... 57
5.6 Response times for a 4 IQ-SENSE electronic module ............................................................... 58
5.7 Response times for technology modules.................................................................................... 58
Index........................................................................................................................................................ 59

Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 7
Properties 1
1.1 IM 151-3 PN HIGH FEATURE interface module
Properties
The IM151-3 PN HIGH FEATURE interface module offers the following features:
● It interconnects ET 200S with PROFINET IO.
● It prepares the data for the assembled electronic modules and motor starters.
● It supplies the rear panel bus.
● Transfer and backup of the device name on SIMATIC Micro Memory Card
● Updating firmware
– Using SIMATIC Micro Memory Card
– Via PROFINET IO
● The reference potential M of the rated supply voltage of the IM151-3 PN HIGH FEATURE
to the rail (protective conductor) is connected by means of an RC combination and
therefore enables earth-free configuration.
● Interrupts
– Diagnostic interrupts
– Process interrupts
– Insert/remove module interrupts
– Maintenance interrupts
● The maximum address space is 256 bytes I/O data.
● IM151-3 PN HIGH FEATURE can be operated with up to 63 modules.
● The maximum bus length at the rear panel bus is 2 m.
● Grouping of modules within one byte (packing).
● Use of fail-safe modules
● Records for IO modules
● Option handling

Properties
1.1 IM 151-3 PN HIGH FEATURE interface module
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
8 Manual, 08/2010, A5E01584258-04
Properties via PROFINET IO
● Integrated switch with 2 ports
● Supported Ethernet services: ping, arp, Net diagnostics (SNMP) / MIB-2, LLDP
● Port diagnostics
● Port disabling
● Isochronous Real-Time Communication
● Minimum update time 250 μs
● Prioritized startup
● Device replacement without exchangeable media/programming device
● Shared Device
● Media redundancy
● supports PROFIenergy
Isochronous Real-Time Communication
Synchronized transmission method for the cyclic exchange of IRT data between PROFINET
devices. A reserved bandwidth within the send clock is available for the IRT IO data. The
reserved bandwidth ensures that IRT data can be transferred at reserved synchronized
intervals, without being influenced by other higher network loads (e.g., TCP/IP
communication, or additional real-time communication).
● IRT option "high flexibility":
Maximum flexibility in planning and extending the system. It is not necessary to configure
the topology.
● IRT option "high performance":
Topological configuration is required.
Note
IO controller as a Sync-Master at IRT communication with the IRT option "high
performance"
We recommend also operating the IO controller as a Sync-Master if you configure the IRT
communication with the option "high performance".
Otherwise, IRT and RT configured IO devices may fail if the Sync-Master fails.
Note
Quantity structure of modules up to EZ3 and IRT option "high performance"
The maximum address space is 146 bytes I/O data when the IRT option "high
performance" is used. If you use a module having the product version EZ1, EZ2 or EZ3,
you should limit the quantity structure to 146 bytes I/O data. Otherwise communication
may be interrupted.
For more information about configuring synchronized PROFINET devices in Sync domains,
refer to the STEP 7 online help and the PROFINET system description
(http://support.automation.siemens.com/WW/view/en/19292127) manual.

Properties
1.1 IM 151-3 PN HIGH FEATURE interface module
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 9
Prioritized startup
Prioritized startup denotes the PROFINET functionality for accelerating the startup of IO
devices within a PROFINET IO system with RT and IRT communication.
The function reduces the time that the correspondingly configured IO devices require in
order to return to the cyclic user data exchange in the following cases:
● After the power supply has returned
● After a station has come back online
● After IO devices have been activated
Note
At a prioritized startup a firmware update using the Micro Memory Card is not possible. It
is possible to perform a firmware update via the LAN network.
Note
Ramp-up time depends on the number and type of modules.
Cabling with fixed connection setting
If you set a fixed connection setting of the port in STEP 7, then you should also disable
"Autonegotiation/Autocrossover."
For additional information, refer to the STEP 7 Online Help and the PROFINET system
description (http://support.automation.siemens.com/WW/view/en/19292127) Manual.
Device replacement without exchangeable media/programming device
IO devices having this function can be replaced simply:
● An exchangeable medium (such as Micro Memory Card) with the stored device name is
not required.
● The device name does not have to be assigned using the programming device.
Instead of being assigned a device name from the exchangeable medium or programming
device, the IO Device is now assigned a device name by the IO Controller. The IO Controller
uses the configured topology and the correlations derived from the IO Devices. The
configured setpoint topology must agree with the actual topology.
We recommend that you reset IO devices that have already been operated to their default
settings before you use them again.
For additional information, refer to the STEP 7 online help and the PROFINET system
description (http://support.automation.siemens.com/WW/view/en/19292127) manual.

Properties
1.1 IM 151-3 PN HIGH FEATURE interface module
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
10 Manual, 08/2010, A5E01584258-04
Requirements
The following requirements apply to a configuration with the
IM 151-3 PN HIGH FEATURE(6ES7151-3BA23-0AB0) interface module:
● You can only use the IM 151-3 PN HIGH FEATURE in operation with the IRT option "high
performance" with STEP 7 as of V5.4 SP4.
● Topology configuration when you configure IRT with the option "high performance".
Reset to factory settings
NOTICE
The stations of a bus segment can fail during the reset to factory settings.
SNMP parameters in non-volatile memory are reset to factory settings (as of STEP 7 V5.3
SP 3) in the HW Config dialog "Target system > Ethernet > Edit Ethernet nodes", "Reset"
button at "Reset to factory settings".
The following data is not deleted during the reset:
● The MAC address
● The I&M0 data
Note
Deleting the device name
The device name is deleted by the "Reset to factory settings" function.
Note
Substitute value behavior at a reset to factory setting
At a "Reset to factory setting" the modules in the station take on the configured substitute
value behavior or the non-configured state.
Compatibility with the predecessor module
The interface module IM151-3 PN HIGH FEATURE(6ES7151-3BA23-0AB0) is compatible
with interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA20-0AB0 and
6ES7151-3BA22-0AB0).
The new interface module directly replaces the predecessor module in an existing system
without the need for reconfiguration.
An IM151-3BA23 that has been in operation and will now be used as spare part has to be
reset to the state "reset to factory settings."
A firmware update of the predecessor module IM151-3BA22 is not supported.
Configuring
You configure the interface module IM151-3 PN HIGH FEATURE with STEP 7 V5.4 SP 4.

Properties
1.1 IM 151-3 PN HIGH FEATURE interface module
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 11
Media redundancy
Function for ensuring the network and system availability. Redundant transmission links (ring
topology) ensure that an alternative communication path is made available if a transmission
link fails.
For additional information, refer to the STEP 7 online help and the PROFINET system
description (http://support.automation.siemens.com/WW/view/en/19292127) manual.
Shared Device
IO device that makes its data available to several IO controllers.
The function Shared Device is not available with the IRT option "high flexibility".
Note
Note that the power and electronics modules of a potential group have to be assigned to the
same IO controller so that a load voltage failure can be diagnosed.
For additional information, refer to the STEP 7 online help and the PROFINET system
description (http://support.automation.siemens.com/WW/view/en/19292127) manual.
Option handling
Option handling enables you to set up your automation system for future expansions or
options. Option handling means that you configure the planned maximum configuration of
your automation system in advance and can vary later depending on the user program.
Option handling exists with and without RESERVE modules and adding options.
For additional information, refer to the sections Option handling (Page 23) in the STEP 7
online help and the PROFINET system description
(http://support.automation.siemens.com/WW/view/en/19292127) manual.
PROFIenergy
Function for energy saving in process, e.g. during break times by briefly switching off the
encoder and load supply in the potential group using standard PROFIenergy commands.
You need the power module PM-E DC24V/8A RO.
For additional information, refer to the STEP 7 online help and the PROFINET system
description (http://support.automation.siemens.com/WW/view/en/19292127) manual.
An example is available in PROFIenergy user program
(http://support.automation.siemens.com/WW/view/en/41986454).

Properties
1.1 IM 151-3 PN HIGH FEATURE interface module
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
12 Manual, 08/2010, A5E01584258-04
Limitations for operation of the modules with IM151-3 PN HIGH FEATURE
The following modules cannot be used with the IM151-3 PN HIGH FEATURE:
Module Up to order number Up to product version
2AO U; HIGH FEATURE 6ES7135-4LB01-0AB0 3
2AO I; HIGH FEATURE 6ES7135-4MB01-0AB0 3
1SI serial interface module 6ES7138-4DF00-0AB0 4
Modbus/USS serial interface module 6ES7138-4DF01-0AB0 4
2PULSE 6ES7138-4DD00-0AB0 6
1Count 24V/100kHz 6ES7138-4DA03-0AB0 -
Motor starter
Direct starter
Reversing starter
3RK1301-xxxxx-0AA1
3RK1301-xxxxx-1AA1
-
-
Pin assignment
The following table shows the pin assignment of the IM151-3 PN HIGH FEATURE interface
module for the 24 VDC voltage supply and of the RJ45 interfaces for PROFINET IO:
Table 1- 1 Pin assignment of the IM151-3 PN HIGH FEATURE
View Signal name Name
1 TD Transmit data +
2 TD_N Transmit Data –
3 RD Receive data +
4 GND Ground
5 GND Ground
6 RD_N Receive Data –
7 GND Ground
8 GND Ground
1L+ 24 VDC
2L+ 24 VDC (for loop through)
1M Ground
/
/
0
0


/
/

0
0
6KLHOGLQJ
2M Chassis ground (for loop through)

Properties
1.1 IM 151-3 PN HIGH FEATURE interface module
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 13
Schematic circuit diagram
/,1. 5;7; 6) %) 21
)2
5-
5-
3
3
3
3
6ZLWFK(OHFWURQLF
5HDUSDQHOEXV
(76
UHDUSDQHO
EXV
FRQQHFWLRQ
352),1(7
FRQQHFWLRQ
(OHFWULFDO
LVRODWLRQ
,QWHUQDO
SRZHUVXSSO\
6,0$7,&0LFUR
0HPRU\&DUG
Figure 1-1 Block diagram of the IM151-3 PN HIGH FEATURE interface module
Technical specificationsIM151-3 PN HIGH FEATURE(6ES7151-3BA23-0AB0)
Dimensions and weight
Dimension B (mm) 60
Weight Approx. 150 g
Module-specific data
Transmission rate 10 Mbps for Ethernet services
100 Mbps full duplex for PROFINET IO
Transmission method 100BASE-TX
Send cycle IRT with the option "high performance" 250
µs to 4 ms in 125-µs increments
RT and IRT with the option "high flexibility":
250 μs, 500 μs, 1 ms
Autonegotiation Yes
Autocrossing Yes
Bus protocol PROFINET IO
Supported Ethernet services ping
arp
LLDP
Net diagnostics (SNMP)/MIB-2
Prioritized startup
Media redundancy
Shared Device
PROFINET interface 2x RJ45
Manufacturer's code (VendorID) 002AH
Device ID (DeviceID) 0301H

Properties
1.2 SNMP
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
14 Manual, 08/2010, A5E01584258-04
Voltages, currents, potentials
Rated supply voltage of the electronic
components (1L+)
24 VDC
Reverse-polarity protection Yes
Voltage failure bypass Min. 20 ms
Galvanic isolation
Between the rear panel bus and electronic
components No
Between Ethernet and electronic components Yes
Between the supply voltage and electronic
components No
Permitted potential difference (to the rail) 75 VDC, 60 VAC
Insulation test voltage 500 VDC
Current consumption from rated supply voltage
(1L+)
Approx. 200 mA
Power loss of the module Approx. 3.3 W
Status, Interrupts, Diagnostics
Interrupts Yes
Diagnostic function Yes
Group error Red "SF" LED
Bus monitoring PROFINET IO Red "BF" LED
Monitoring of the supply voltage of the
electronics Green "ON" LED
Maintenance requirements (maintenance) Yellow "maint" LED
Existing connection to network One green LED "LINK" per interface
1.2 SNMP
SNMP
The interface module supports the Ethernet service SNMP. MIB-2 (RFC1213) is supported.
R/W objects can be changed using SNMP tools and are stored in the module.
Following replacement with a brand new module, the R/W objects of the interface module
are set to the factory settings.

Properties
1.3 SIMATIC Micro Memory Card
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 15
1.3 SIMATIC Micro Memory Card
Insertion of the SIMATIC Micro Memory Card
A SIMATIC Micro Memory Card is used as a memory medium for the IM 151-3 PN HIGH
FEATURE.
A SIMATIC Micro Memory Card with 64 KB is sufficient for storing the name of the device.
An MMC of 4 MB or higher is required for a firmware update.
Position of the module slot for the SIMATIC Micro Memory Card
5
3
6
4
1
2
3
3
3 5 5
3
6)
%)
07
21
/,1.
;
352),1(7
(76
/$1
/ 0
0/
'&9
6,0$7,&
6,(0(16
0LFUR 0HPRU\ &DUG
%\WH
(6/[$$
7
8
① Group error (red)
② Bus fault (red)
③ Maintenance display (yellow)
④ Supply voltage (green)
⑤ Connection to a switch or IO controller (green)
⑥ SIMATIC Micro Memory Card
⑦ Cable connection
⑧ Locking / unlocking (ejector) of the Micro Memory Card
Insertion of the SIMATIC Micro Memory Card
Note
You can save either process-related data (device names) or firmware update data on one
MMC.

Properties
1.3 SIMATIC Micro Memory Card
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
16 Manual, 08/2010, A5E01584258-04
Service life of a SIMATIC Micro Memory Card
The service life of a SIMATIC Micro Memory Card essentially depends on the following
factors:
● Number of deletion or programming operations
● External factors, such as ambient temperature
At an ambient temperature of up to 60°C, a SIMATIC Micro Memory Card has a service life
of 10 years, with a maximum of 100,000 write/delete operations.
NOTICE
Possible data loss
If the maximum number of write/delete operations is exceeded, data loss is possible.
Available SIMATIC Micro Memory Cards
Table 1- 2 Available SIMATIC Micro Memory Cards
Description As of order number Memory size
SIMATIC Micro Memory Card 64k 6ES7953-8LFxx-0AA0 64 KB
SIMATIC Micro Memory Card 128k 6ES7953-8LGxx-0AA0 128 KB
SIMATIC Micro Memory Card 512k 6ES7953-8LJxx-0AA0 512 KB
SIMATIC Micro Memory Card 2M 6ES7953-8LLxx-0AA0 2 MB
SIMATIC Micro Memory Card 4M 6ES7953-8LMxx-0AA0 4 MB
SIMATIC Micro Memory Card 8M 6ES7953-8LPxx-0AA0 8 MB
Inserting/replacing the SIMATIC Micro Memory Card
Note
In order to ensure that it will function correctly, the SIMATIC Micro Memory Card must only
be inserted or removed with the power turned off.
The beveled corner of the SIMATIC Micro Memory Card prevents it from being inserted the
wrong way round (reverse polarity protection).
To eject the card, push in the ejector with a suitable object (such as a small screwdriver or
ball-point pen).

Properties
1.4 Firmware update
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 17
1.4 Firmware update
Updating firmware
The firmware of an IM 151-3 PN HIGH FEATURE can be updated:
● Using a SIMATIC Micro Memory Card with at least 4 MB of memory.
Additional information can be found on the Internet
(http://support.automation.siemens.com/WW/view/en/19241998/133100).
● Via PROFINET IO, e.g., using HW Config or in the SIMATIC Manager via "Target system
> Display accessible nodes".
For additional information, refer to the
STEP 7 Online Help.
Requirements
In order to update the firmware of an IM 151-3 PN HIGH FEATURE you require:
●
STEP 7 , V5.3 or higher, SP 2
● SIMATIC Micro Memory Card (MMC) for the MMC update
● A PC or programming device with a facility for writing to a SIMATIC Micro Memory Card
NOTICE
When the firmware is updated, the stations in a line can fail.
Note
A firmware update with SIMATIC Micro Memory Card is not possible for interface modules
that were started with the "Prioritized startup" parameter. In this case you can delete the
parameter "Prioritized startup" by a "Reset to factory settings". Firmware updating with the
SIMATIC Micro Memory Card is subsequently possible again.

Properties
1.4 Firmware update
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
18 Manual, 08/2010, A5E01584258-04

Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
Manual, 08/2010, A5E01584258-04 19
Parameters 2
2.1 Parameters for the IM151-3 HIGH FEATURE interface module
Table 2- 1 Parameters for IM151-3 interface module
IM151-3 Value range Default setting Applicability
Bus length ≤ 1 m/> 1 m ≤ 1 m ET 200S
Interference frequency
suppression
50 Hz/60 Hz 50 Hz ET 200S
Reference junction slot None/2 to 63 None ET 200S
Reference junction input RTD on channel 0/
RTD on channel 1
0 ET 200S
Release option handling Yes/no No ET 200S
2.2 Parameter description
2.2.1 Bus length
≤ 1 m: The default setting for the maximum bus length is 1 m.
> 1 m: The bus length of the ET 200S is > 1 m and can be up to 2 m. However, this setting
will increase the response time of the ET 200S.
2.2.2 Interference frequency suppression
The frequency of your AC power system can interfere with the measured value especially
when measuring in low voltage ranges and using thermocouple elements. Enter the line
frequency for your system here (50 Hz or 60 Hz).
The interference frequency suppression parameter applies to all analog electronic modules.
This parameter is also used to specify the integration and conversion time of the various
modules. See the technical data for the analog electronic modules.

Parameters
2.2 Parameter description
Interface module IM151-3 PN HIGH FEATURE (6ES7151-3BA23-0AB0)
20 Manual, 08/2010, A5E01584258-04
2.2.3 Reference junction slot
This parameter allows you to assign a slot (none, 2 to 63) with a channel for measuring the
reference temperature (calculation of the compensation value).
Reference
Refer to the manuals for the analog electronic modules for information on connecting
thermocouples.
2.2.4 Reference junction input
This parameter can be used to set the channel (0/1) for measuring the reference
temperature (calculation of the compensation value) for the assigned slot.
Reference
Refer to the manuals for the analog electronic modules for information on connecting
thermocouples.
2.2.5 Release option handling
Release option handling
Use this parameter to release the function option handling in the ET 200S.
Note
If you configure the release, then the ET 200S requires a control data record from the user
program so that the station can serve the I/O modules.