Siemens SIMATIC ET 200SP User manual

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
ET 200SP
DQ 4x24..230VAC/2A ST digital
output module
(6ES7132-6FD00-0BB1)
Manual
03/2015
A5E32043575
-AB
Preface
Guide to documentation
1
Product overview
2
Wiring
3
Parameter
assignment/addressing
4
Interrupts/diagnostics alarms
5
Technical specifications
6
Parameter data record
A

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32043575-AB
Ⓟ
12/2016 Subject to change
Copyright © Siemens AG 2014 - 2015.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
4Manual, 03/2015, A5E32043575-AB
Preface
Purpose of the documentation
This manual supplements the system manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
Functions that generally relate to the system are described in this manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the system.
Conventions
CPU: When the term "CPU" is used in this manual, it applies to the CPUs of the S7-1500
automation system as well as to the CPUs/interface modules of the ET 200SP distributed I/O
system.
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, o
n the
handling of the product or on the section of the documentation to which particular attention
should be paid.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. You can find more information about industrial security on the Internet
(http://www.siemens.com/industrialsecurity).
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. You can find more information on the Internet
(http://support.automation.siemens.com).

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 5
Table of contents
Preface ................................................................................................................................................... 4
1 Guide to documentation .......................................................................................................................... 6
2 Product overview .................................................................................................................................... 8
2.1 Properties..................................................................................................................................8
3 Wiring ................................................................................................................................................... 10
3.1 Wiring and block diagram .......................................................................................................10
4 Parameter assignment/addressing ........................................................................................................ 12
4.1 Parameters .............................................................................................................................12
4.2 Explanation of parameters ......................................................................................................13
4.3 Address space ........................................................................................................................14
5 Interrupts/diagnostics alarms................................................................................................................. 15
5.1 Status and fault displays .........................................................................................................15
5.2 Load voltage status.................................................................................................................17
5.3 Interrupts.................................................................................................................................17
5.4 Diagnostics alarms..................................................................................................................17
6 Technical specifications ........................................................................................................................ 18
6.1 Technical specifications ..........................................................................................................18
A Parameter data record .......................................................................................................................... 21
A.1 Parameter assignment and structure of parameter data record.............................................21

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
6Manual, 03/2015, A5E32043575-AB
Guide to documentation
1
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
Basic information
The system manual describes in detail the configuration, installation, wiring and
commissioning of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help
supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, terminal diagrams, characteristics and technical specifications.
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, designing
interference-free controllers.
You can download the documentation free of charge from the Internet
(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-
overview/tech-doc-et200/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.

Guide to documentation
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 7
Manual Collection ET 200SP
The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(http://support.automation.siemens.com/WW/view/en/84133942).
My Documentation Manager
The My Documentation Manager is used to combine entire manuals or only parts of these to
your own manual.
You can export the manual as PDF file or in a format that can be edited later.
You can find the My Documentation Manager on the Internet
(http://support.industry.siemens.com/My/ww/en/documentation).
Application examples
Applications examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus in individual products.
You can find application examples on the Internet
(http://support.industry.siemens.com/cs/ww/en/ps/ae).
CAx Download Manager
The CAx Download Manager is used to access the current product data for your CAx or CAe
systems.
You configure your own download package with a few clicks.
In doing so you can select:
●Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
●Manuals, characteristics, operating manuals, certificates
●Product master data
You can find the CAx Download Manager on the Internet
(http://support.industry.siemens.com/my/ww/en/CAxOnline).
TIA Selection Tool
With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
8Manual, 03/2015, A5E32043575-AB
Product overview
2
2.1
Properties
Article number
6ES7132-6FD00-0BB1
View of the module
①
Module type and name
⑦
Function class
②
LED for diagnostics
⑧
Color coding module type
③
2D matrix code
⑨
Function and firmware version
④
Wiring diagram
⑩
Color code for selecting the color identification labels
⑤
LEDs for channel status
⑪
Article number
⑥
LED for supply voltage
Figure 2-1 View of the DQ 4×24..230VAC/2A ST module

Product overview
2.1 Properties
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 9
Properties
The module has the following technical properties:
●4 digital outputs each with a value status (quality information)
●Supply voltage L+
●Switches in zero point
●Output current 2 A per channel
●Total current 8 A (per module)
●Configurable substitute values (per channel)
●Suitable for solenoid valves, AC contactors, and indicator lights
The module supports the following functions:
●Firmware update
●Identification data I&M0 to I&M3
●Reconfiguration in RUN
●PROFIenergy
You can configure the module with STEP 7 (TIA Portal) and with a GSD file.
Accessories
The following accessories must be ordered separately:
●Labeling strips
●Color identification labels
●Reference identification label
You can find more information on accessories in the ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293) system manual.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
10 Manual, 03/2015, A5E32043575-AB
Wiring
3
3.1
Wiring and block diagram
This section includes the block diagram of the DQ 4x24..230VAC/2A ST module with the
terminal assignments for 2-wire and 3-wire connection.
You can find information on wiring the BaseUnit in the ET 200SP distributed I/O system
system manual.
NOTICE
Dangerous voltage. Risk of death or serious injury.
Always disconnect the system and module from the power supply before commencing
work.
Note
Limiting overvoltage
You must ensure overvoltage is limited to 1
kV for the encoder supply.
Note
Power limitation
To limit power, each input voltage must have a fuse with a maximum rating of 10
A tripping
current. The fuse must be a quick
-acting microfuse.
Note
You may use and combine the different wiring options for all channels.

Wiring
3.1 Wiring and block diagram
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 11
Connection: 2-wire and 3-wire connection of actuators
The following figure shows the block diagram and an example for the terminal assignment of
the digital input module DQ 4x24..230VAC/2A ST on the BaseUnit BU type B1.
①
2-wire connection
N
Neutral
②
3-wire connection
1L, 2L
Supply voltage 120 V AC to 230 V AC
③
Backplane bus interface
1N, 2N
Neutral conductor supply voltage
④
Output electronics
PE (AUX)
Protective conductor connection
⑤
Color identification label CCxx (optional)
DIAG
Diagnostics LED (red/green)
DQn
Output signal, channel n
.0, .1, .2, .3
Channel status LED (green)
L1
Encoder supply
PWR
Power LED (green)
P1,
P2,
AUX
Internal self-assembling voltage buses
Connection to left (dark-colored BaseUnit)
Figure 3-1 Wiring and block diagram for 2-wire and 3-wire connection of actuators
No connection for three-phase loads
The digital output is not suitable for three-phase loads.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 12
Parameter assignment/addressing
4
4.1
Parameters
DQ 4×24..230VAC/2A ST parameters
The table below lists the parameters that can be set. The effective range of the configurable
parameters depends on the type of configuration. The following configurations are possible:
●Central operation with an ET 200SP CPU
●Distributed operation on PROFINET IO in an ET 200SP system
●Distributed operation with PROFIBUS DP in an ET 200SP system
When performing the configuration in the user program, use the "WRREC" instruction to
transfer the parameters to the module using data records (refer to the section Parameter
assignment and structure of parameter data record (Page 21)).
The following parameter settings are possible:
Table 4- 1 Configurable parameters and their defaults (GSD file)
Parameter
Range of values
Default
Recon-
figuration
in RUN
Effective range with configuration software, e.g.
STEP 7 (TIA Portal)
GSD file PROFINET IO
GSD file PROFIBUS DP1
Operating mode •Channel activated
•Channel deactivated
Channel
activated
Yes Channel Channel
Reaction to
CPU STOP
•Turn off
•Keep last value
•Output substitute value 1
Turn off Yes Channel Module
1
Only for configuration using the PROFIBUS GSD file; does not affect configuration with STEP 7 using HSP: As the
number of parameters with PROFIBUS GSD configuration is limited to a maximum of 244 bytes per ET 200SP station,
the configuration options are limited. If required, however, you can still set this parameter using data record 128 as de-
scribed in the column "GSD file PROFINET IO" (see the table above). The parameter length of the I/O module is 3
bytes.

Parameter assignment/addressing
4.2 Explanation of parameters
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 13
4.2
Explanation of parameters
Operating mode
Determines whether a channel is enabled or disabled.
Reaction to CPU STOP
Determines the behavior of the module in the event of a CPU STOP.
See also
ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293)

Parameter assignment/addressing
4.3 Address space
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
14 Manual, 03/2015, A5E32043575-AB
4.3
Address space
Configuration options of DQ 4×24..230VAC/2A ST
The following configurations are possible:
●Configuration 1: Without value status
●Configuration 2: With value status
Evaluating the value status
An additional byte is allocated in the input address space if you enable the value status for
the digital module. Bits 0 to 3 in this byte are assigned to a channel. They provide
information about the validity of the digital value.
Bit =1: No fault is present on the channel.
Bit =0: Channel is deactivated or there is an error on the module.
If an error on a channel occurs with this module, the value status for all channels is 0.
Address space of the digital output module DQ 4×24..230VAC/2A ST
The following figure shows the assignment of the address space for the
DQ 4×24..230VAC/2A ST with value status (Quality Information (QI)). The addresses for the
value status are only available if the value status is enabled.
Figure 4-1 Address space of the DQ 4×24..230VAC/2A ST digital output module with value status

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
15 Manual, 03/2015, A5E32043575-AB
Interrupts/diagnostics alarms
5
5.1
Status and fault displays
LED display
The figure below shows the LED displays of the DQ 4×24..230VAC/2A ST.
①
DIAG (green/red)
②
Channel status (green)
③
PWR (green)
Figure 5-1 LED displays
Meaning of the LEDs
The following tables explain the meaning of the status and error displays.

Interrupts/diagnostics alarms
5.1 Status and fault displays
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
16 Manual, 03/2015, A5E32043575-AB
DIAG LED
Table 5- 1 Error display of the DIAG LED
DIAG LED
Meaning
Off
Backplane bus supply of the ET 200SP not OK
Flashes
Module parameters not assigned
On
Module parameters assigned and no module diagnostics
Flashes
Module parameters assigned and module diagnostics
Channel status LED
Table 5- 2 Status display of the channel status LED
Channel status
LED
Meaning
Off
Channel deactivated or activated and process signal = 0
On
Channel activated and process signal = 1
PWR LED
Table 5- 3 Status display of the PWR LED
PWR LED
Meaning
Off
No supply voltage L+
On
Supply voltage L+ present

Interrupts/diagnostics alarms
5.2 Load voltage status
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 17
5.2
Load voltage status
Load voltage status
The firmware of the module cannot detect the status of the load voltage.
If the "Load voltage status" function tied to the server module is used, a "1" is always
displayed in the status bit for a slot with the DQ 4×24..230VAC/2A ST. Even when the load
voltage is not applied.
The state of the load voltage at the terminal does not impact the PROFIenegy behavior.
5.3
Interrupts
The DQ 4x24...230VAC/2A ST digital output module supports diagnostics interrupts.
Diagnostics interrupts
The module generates a diagnostic interrupt at the following events:
●Channel temporarily unavailable
●Parameter assignment error
5.4
Diagnostics alarms
Diagnostics alarms
A diagnostics alarm is output for each diagnostics event and the DIAG LED flashes on the
module. The diagnostics alarms can, for example, be read from the diagnostics buffer of the
CPU. You can evaluate the error codes with the user program.
Table 5- 4 Diagnostics alarms, their meaning and corrective measures
Diagnostics alarm
Error code
Meaning
Solution
Parameter assignment
error
10H•The module cannot evaluate parameters
for the channel.
•Incorrect parameter assignment.
Correct the parameter assignment
Channel/component
temporarily unavailable
1FHFirmware update is currently in progress or
has been canceled. The module does not
read in process values in this state.
•Wait for firmware update
•Restart the firmware update

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 18
Technical specifications
6
6.1
Technical specifications
Technical specifications of the DQ 4×24...230VAC/2A ST
6ES7132-6FD00-0BB1
Product type designation
DQ 4x24 ... 230VAC/2A
General information
Firmware version
V1.0
•
FW update possible Yes
Usable BaseUnits
BU type B1
Color code for module
-specific color identification
label
CC41
Product function
I&M data
Yes; I&M0 to I&M3
Engineering with
STEP
7 TIA Portal can be configured/integrated
as of version
V13 / V13
STEP 7 can be configured/integrated as of version
V5.5 SP3 / -
PROFIBUS as of GSD version/GSD revision
GSD as of revision 5
PROFINET as of GSD version/GSD revision
GSDML V2.3
Operating mode
DQ
Yes
DQ with energy-saving function
No
PWM
No
Oversampling
No
MSO
No
Supply voltage
Rated value (AC)
230 V
Input current
Current consumption (rated value)
11.5 mA
Power loss
Power loss, typ.
9 W; active power, load voltage 230 V, all outputs
loaded with 2 A, 50 Hz
Address area
Address space per module
Address space per module, max.
1 byte; + 1 byte for QI information
Input
1 byte; with QI
Output
1 bytes

Technical specifications
6.1 Technical specifications
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 19
6ES7132-6FD00-0BB1
Digital outputs
Number of outputs
4
Sinking output
No
Sourcing output
Yes
Short-circuit protection
No; install a fuse with 10A trigger current when
using a type B1 BU
Switching capacity of outputs
With resistive load, max.
2 A
With lamp load, max.
100 W
Output voltage
For signal "1", min.
20.4 V
Output current
For signal "1" rated value
2 A
For signal "1" permitted range, min.
10 mA
For signal "1" permitted range, max.
2 A
For signal "0" residual current, max.
460 µA
Output delay with resistive load
"0" to "1", max.
10 ms
"1" to "0", max.
10 ms
Parallel switching of 2 outputs
For logic operations
No
For increased performance
No
For redundant control of a load
Yes
Switching frequency
With resistive load, max.
10 Hz
With inductive load, max.
0.5 Hz
With lamp load, max.
1 Hz
Total current of outputs
Current per channel, max.
2 A
Current per module, max.
8 A
Total current of outputs (per module)
Horizontal installation
•
up to 40 °C, max. 8 A
•
up to 50 °C, max. 6 A
•
up to 60 °C, max. 4 A
Vertical installation
•
up to 30 °C, max. 8 A
•
up to 40 °C, max. 6 A
•
up to 50 °C, max. 4 A
Output current per channel
Horizontal installation
•
up to 60 °C, max. 2 A
Vertical installation
•
up to 50 °C, max. 2 A

Technical specifications
6.1 Technical specifications
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
20 Manual, 03/2015, A5E32043575-AB
6ES7132-6FD00-0BB1
Triac outputs
Size of motor starter according to NEMA, max.
5
Cable length
Shielded, max.
1000 m
Unshielded, max.
600 m
Isochronous mode
Isochronous mode (application synchronized up to
terminal)
No
Interrupts/diagnostics/status information
Substitute values can be applied
Yes
Interrupts
Diagnostics interrupt
No
Diagnostics alarms
Diagnostics
No
Monitoring of supply voltage
No
Diagnostics indicator LED
Monitoring of the supply voltage (PWR LED)
Yes; green PWR LED
Channel status display
Yes; green LED
For module diagnostics
Yes; green/red DIAG LED
Electrical isolation
Electrical isolation of channels
Between the channels
No
Between the channels and the backplane bus
Yes
Between the channels and the supply voltage of
the electronics
No
Insulation
Insulation tested with
DC 2545 V 2 s (routine test)
Dimensions
Width
20 mm
Weights
Weight, approx.
50 g
Dimension drawing
See the manual ET 200SP BaseUnits
(http://support.automation.siemens.com/WW/view/en/59753521)