Siemens SIMATIC S7 EIP-200S User guide

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
S7
EIP-200S Ethernet/IP Adapter
Distributed I/O System
System Manual
06/2018
A5E44345053
-AB
Preface
Product overview
1
EIP-200S Ethernet/IP
Adapter
2
Installation and wiring
3
Commissioning and
diagnostics
4
General technical
specifications
5
Order number
A
Dimension drawings
B
Address space of the ET
200S inputs and outputs
C

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: ZNX-EIP-200S
Ⓟ
06/2018 Subject to change
Copyright © Siemens AG 2018.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 3
Preface
Trademarks
This manual references technologies whose names are trademarked by ODVA, the Open
DeviceNet Vendors Association. The ODVA technologies referenced in this manual include:
●EtherNet/IP™
●CIP™ (Common Industrial Protocol)
●QuickConnect™
For more information on ODVA and its trademarked technologies, visit the ODVA website
(http://www.odva.org).
Purpose of the manual
The information in this manual is intended to enable you to operate the EIP-200S Ethernet/IP
Adapter on Ethernet/IP.
Required basic knowledge
To understand this manual, it is necessary to have a general knowledge of automation
engineering.
Scope of the manual
This manual describes the following product:
EIP-200S Ethernet/IP Adapter
Certifications, Marks, and Standards
The EIP-200S Ethernet/IP Adapter complies with Ethernet/IP Specification CIP Networks
Library Volume 2: Ethernet/IP Adaption of CIP, Edition 1.22.
Refer to General technical specifications (Page 91) for more information.
Service and Support
In addition to our documentation, Siemens offers technical expertise on the Internet and on
the customer support web site (http://support.industry.siemens.com).
Contact your Siemens distributor or sales office for assistance in answering any technical
questions, for training, or for ordering S7 products. Because your sales representatives are
technically trained and have the most specific knowledge about your operations, process
and industry, as well as about the individual Siemens products that you are using, they can
provide the fastest and most efficient answers to any problems you might encounter.

Preface
EIP-200S Ethernet/IP Adapter Distributed I/O System
4System Manual, 06/2018, A5E44345053-AB
Documentation and information
The following list shows a summary of the documentation packages or manuals related to
the ET 200S system, which can be found on the Siemens Service & Support Website
(http://support.automation.siemens.com)
●EIP-200S Ethernet/IP Adapter (this manual)
●ET 200S Distributed I/O System Operating Instructions
●ET 200S Distributed I/O System Manuals:
–Interface Modules
–PM-E Power Modules
–Reserve Modules
–Digital Electronic Modules
–Analog Electronic Modules
●Terminal Modules for Power and Electronic Modules
●Motor Starters and Frequency Converters
See also
Automation / partner (http://www.siemens.com/automation/partner)
Automation support (http://support.automation.siemens.com)
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens' products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under (https://www.siemens.com/industrialsecurity).

EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 5
Table of contents
Preface ................................................................................................................................................... 3
1 Product overview .................................................................................................................................... 7
1.1 What are distributed I/O systems?............................................................................................7
1.2 What is the ET 200S distributed I/O system?...........................................................................7
1.3 The EIP-200S Ethernet/IP Adapter.........................................................................................11
1.4 Features and benefits of the EIP-200S Ethernet/IP Adapter..................................................13
1.5 What is Device Level Ring (DLR)? .........................................................................................14
2 EIP-200S Ethernet/IP Adapter............................................................................................................... 15
2.1 Operation ................................................................................................................................17
2.2 Parameters for the EIP-200S Ethernet/IP Adapter.................................................................20
2.3 Faults / diagnostics .................................................................................................................21
2.4 Troubleshooting ......................................................................................................................23
2.5 Replacing a faulty EIP-200S Adapter .....................................................................................24
2.6 Device profile: supported CIP objects.....................................................................................25
2.6.1 Identity Object .........................................................................................................................25
2.6.2 Assembly Object .....................................................................................................................28
2.6.3 Connection Manager Object ...................................................................................................30
2.6.4 TCP/IP Interface Object..........................................................................................................31
2.6.5 Ethernet Link Object ...............................................................................................................35
2.6.6 Device Level Ring (DLR) Object.............................................................................................40
2.6.7 Quality of Service (QoS) .........................................................................................................41
2.7 Device profile: vendor-specific objects ...................................................................................43
2.7.1 Adapter Object ........................................................................................................................43
2.7.2 Slot Object ..............................................................................................................................47
2.8 Technical specifications..........................................................................................................52
3 Installation and wiring............................................................................................................................ 53
3.1 Installation...............................................................................................................................53
3.2 Installation rules ......................................................................................................................53
3.3 Installing the EIP-200S Ethernet/IP Adapter ..........................................................................54
3.4 Inserting and identifying the electronic modules.....................................................................55
3.5 Wiring and setup .....................................................................................................................59
3.6 General rules and regulations for operating the EIP-200S Ethernet/IP Adapter ....................59
3.7 Operating the ET 200S on a grounded supply .......................................................................61
3.8 Electrical design of the ET 200S.............................................................................................64

Table of contents
EIP-200S Ethernet/IP Adapter Distributed I/O System
6System Manual, 06/2018, A5E44345053-AB
3.9 Wiring the ET 200S................................................................................................................ 65
3.9.1 Wiring rules for the ET 200S.................................................................................................. 65
3.9.2 Wiring a terminal module with screw-type terminals.............................................................. 65
3.9.3 Wiring a terminal module with spring terminals ..................................................................... 66
3.9.4 Wiring a terminal module with Fast Connect ......................................................................... 68
3.9.5 Wiring terminal modules for power and electronic modules .................................................. 72
3.9.6 Wiring the EIP-200S Ethernet/IP Adapter.............................................................................. 76
4 Commissioning and diagnostics ............................................................................................................ 79
4.1 Configuring the ET 200S........................................................................................................ 79
4.2 Commissioning and startup of the ET 200S .......................................................................... 84
4.3 Configuring the EIP-200S Ethernet/IP Adapter ..................................................................... 84
4.4 Setting the IP address............................................................................................................ 84
4.5 Using QuickConnect .............................................................................................................. 85
4.5.1 Guidelines for using QuickConnect on your network............................................................. 86
4.5.2 Replacing a faulty QuickConnect Adapter ............................................................................. 89
4.5.3 Troubleshooting and optimization.......................................................................................... 89
4.6 Firmware updates .................................................................................................................. 90
5 General technical specifications ............................................................................................................ 91
5.1 General technical specifications ............................................................................................ 91
5.2 Standards Compliance........................................................................................................... 91
5.3 Use of subassemblies/modules in a Zone 2 hazardous area................................................ 98
A Order number ......................................................................................................................................103
B Dimension drawings.............................................................................................................................105
C Address space of the ET 200S inputs and outputs ...............................................................................107
Index ...................................................................................................................................................109

EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 7
Product overview
1
1.1
What are distributed I/O systems?
Distributed I/O systems - area of application
When a system is set up, the inputs and outputs from and to the process are often located
centrally in the programmable logic controller.
If there are inputs and outputs at considerable distances from the programmable logic
controller, there may be long runs of cabling which are not immediately comprehensible, and
electromagnetic interference may impair reliability.
Distributed I/O systems are the ideal solution in such cases:
●The controller CPU is located centrally.
●The I/O systems (inputs and outputs) operate locally on a distributed basis.
●The high-performance EIP-200S Ethernet/IP Adapter network ensures that the controller
CPU and I/O systems communicate smoothly.
1.2
What is the ET 200S distributed I/O system?
The ET 200S distributed I/O system is a modular, extremely flexible I/O system with IP20
degree of protection.
Area of application
You can connect virtually any number of I/O modules in virtually any combination right next
to the interface module. This means you can adjust the configuration to suit local
requirements.
Depending on the interface module, each ET 200S system can consist of up to 63 modules -
for example, power modules, I/O modules, and motor starters.
The fact that motor starters can be integrated (switching and protecting any three-phase load
up to 7.5 kW) ensures that the ET 200S can be quickly adapted to suit virtually any process-
related use of your machine.
Terminal modules and electronic modules
The ET 200S distributed I/O system consists primarily of various passive terminal modules to
which you connect the electronic modules and motor starters.
The EIP-200S Ethernet/IP Adapter enables the ET 200S distributed I/O system to be
connected to the Ethernet/IP network.

Product overview
1.2 What is the ET 200S distributed I/O system?
EIP-200S Ethernet/IP Adapter Distributed I/O System
8System Manual, 06/2018, A5E44345053-AB
View
The illustration below shows an example of an ET 200S distributed I/O system configuration:

Product overview
1.2 What is the ET 200S distributed I/O system?
EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 9
ET 200S components
The table below provides an overview of the most important components of the ET 200S
system:
Component
Function
Drawing
Rail Carries the ET 200S. You mount the ET 200S on the
rail.
Interface module: EIP-200S
Ethernet/IP Adapter
Connects the ET 200S with the EIP-200S Ethernet/IP
Adapter and prepares the data for the electronic
modules and motor starters.
Terminal module Carries the wiring and receives the power and elec-
tronic modules. Terminal modules are available in the
following variants:
•For power modules
•For electronic modules
•With screw-type terminal
•With spring terminal
•With Fast Connect (quick connection method, no
stripping required)
Power module Monitors the voltage for all the electronic modules in
the potential group. The following power modules are
available:
•For a 24 VDC supply with diagnostics
•For a 24 to 48 VDC supply with diagnostics
•For a 24 to 48 VDC, 24 to 230 VAC supply with
diagnostics and fuse

Product overview
1.2 What is the ET 200S distributed I/O system?
EIP-200S Ethernet/IP Adapter Distributed I/O System
10 System Manual, 06/2018, A5E44345053-AB
Component
Function
Drawing
Electronic module Is connected to the terminal module and determines
the function:
•Digital input modules with 24 VDC, 120/230 VAC
and NAMUR
•Digital output modules with 24 VDC and
120/230 VAC
•Relay modules
•Analog input modules with voltage, current, and
resistance measurement; thermal resistance; and
thermocouples
•Analog output modules for voltage and current
Terminating module Terminates the ET 200S and can be used to carry 6
reserve fuses (5 mm x 20 mm).
Shield contact For connecting cable shields.
Slot number labels For identifying the slots on the terminal module.
Color identification labels Permit customer and country-specific identification of
the terminals on the terminal module.
Labeling sheet (DI A4, perfo-
rated, foil)
For machine labeling or printing - 80 strips per label-
ing sheet

Product overview
1.3 The EIP-200S Ethernet/IP Adapter
EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 11
1.3
The EIP-200S Ethernet/IP Adapter
EIP-200S Ethernet/IP Adapter interface module package
The EIP-200S Ethernet/IP Adapter module package includes as one unit the following listed
components:
●Interface module and terminating module (EIP-200S Ethernet/IP Adapter)
●Companion Disk with EIP ET200 Configuration Tool and EIP ET200 Configuration Tool
User Manual
●Power connector
●SD memory card (6ES7954-8LC03-0AA0)
Order number
ZNX-EIP-200S
EIP-200S Ethernet/IP Adapter module features
The EIP-200S Ethernet/IP Adapter is a communications adapter for interfacing to the
Siemens SIMATIC ET 200S distributed I/O system. It provides connectivity between an
Ethernet/IP network and ET 200S power and I/O modules, and has the following features:
●It prepares the data for the electronic modules and motor starters that are fitted.
●It supplies the backplane bus.
●The maximum address space is 255 bytes for inputs and 255 bytes for outputs.
●The reference potential M of the rated supply voltage of the interface module to the rail
(protective conductor) is connected by means of an RC combination, thus permitting an
ungrounded configuration.
●A maximum of 63 modules can be operated with the interface module.
●The maximum width of the station is 1 m. The width can be between 1 m and 2 m, but the
adapter Bus Length parameter must be set to >1 m, and the response time would
increase. See the topic entitled "Parameters" for more information.
●The maximum parameter length for the entire station is 237 bytes.
●Grouping of modules within one byte (packing)
●Device Level Ring (DLR) operation

Product overview
1.3 The EIP-200S Ethernet/IP Adapter
EIP-200S Ethernet/IP Adapter Distributed I/O System
12 System Manual, 06/2018, A5E44345053-AB
The following illustration shows the hardware features of the EIP-200S Ethernet/IP Adapter
module:
24 VDC terminals
The 24 VDC Quick Release terminal connector on the front of the EIP-200S Ethernet/IP
Adapter module provides logic power for the adapter module itself.
I/O features
The EIP-200S Ethernet/IP Adapter provides the following I/O features:
●Provides support for most ET 200S modules
●Supports up to 63 modules per EIP-200S Ethernet/IP Adapter module
●Supports electronic module parameterization
●Supports electronic module diagnostics

Product overview
1.4 Features and benefits of the EIP-200S Ethernet/IP Adapter
EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 13
1.4
Features and benefits of the EIP-200S Ethernet/IP Adapter
The following table lists the features and benefits of the EIP-200S Ethernet/IP Adapter:
Features
Benefits
Structure
Finely-graduated modular design:
•1/2/4/8 channel electronic modules
•Power modules
•Integrated motor starters
•Function-oriented, cost-optimized station design
•Considerable reduction in outlay for configuration
and documentation
•Space savings due to arbitrary arrangement of
the modules
Extensive range of electronic modules
Broad area of application
Communication capacity, system-integrated
motor starter: direct and reversing starter to
7.5 kW
PLC inputs and outputs, terminal blocks, circuit
breakers and contactors in a plug-in module save
space and the effort involved in wiring
Permanent wiring due to the separation of
mechanical and electronic components
•Prewiring possible
•Module replacement during operation of the
EIP-200S ("hot swapping")
Individual connection of power modules to
common potential
•Individual formation of potential groups (identifia-
ble by color coding of the TM-P terminal modules
for power modules)
•Simple load interruption
DLR media redundancy Ring structures with Device Level Ring (DLR) sup-
port
Robust structure for rough industrial condi-
tions (5 g vibration resistance)
High operating reliability when mounted directly on
the machine, high availability
Connection system
Integrated voltage buses
Reduced effort required for wiring
Power bus up to 50 A for motor starters
Minimization of wiring in 400 V range
Screw-type terminals, spring terminals, and
Fast Connect
A change in terminal connection method is not nec-
essary
•2- and 3-wire connection, or
•2-, 3-, and 4-wire connection
Optimal selection on grounds of space and cost
Fast Connect •Quick connection method with no stripping re-
quired
•Saves time with wiring
Terminal box in terminal module replaceable No need to remove the terminal module in the event
of terminal damage
Automatic coding of the I/O modules
Quick and reliable module replacement
Large label plate
Adequate space for clear identification
With motor starters up to safety category 4 in
accordance with EN 954-1
Saves money on costly safety equipment

Product overview
1.5 What is Device Level Ring (DLR)?
EIP-200S Ethernet/IP Adapter Distributed I/O System
14 System Manual, 06/2018, A5E44345053-AB
1.5
What is Device Level Ring (DLR)?
DLR network
A DLR network is a single-fault-tolerant ring network that is intended for the interconnection
of automation devices without the need for more switches. This topology is also implemented
at the device level. The ring topology offers the following advantages:
●Media redundancy
●Fast-network fault detection and reconfiguration
●Resiliency of a single-fault-tolerant network
●Easy implementation without more hardware requirements
The DLR network includes at least one node configured to be a ring supervisor, and any
number of normal ring nodes utilizing embedded switch technology. The ZNX:EIP200S is a
Beacon based ring node and processes the Beacon frames sent by the ring supervisor.
When a fault occurs on the DLR network, the ring nodes reconfigure themselves and relearn
the network topology. Additionally, ring nodes can report fault locations to the active ring
supervisor. For more information about Beacon/Announce based ring nodes, see ODVA
publication, EtherNet/IP Adaptation of CIP, Vol2_1.22, chapter 9-5 Device Level Ring
Protocol.
NOTICE
Important network configuration considerations:
•Depending on your network architecture, DLR topology limitations can exist. Make sure
to validate your DLR topology within the larger network before production use.
•Do not connect non-DLR devices directly to the ring network. Non-DLR devices must be
connected to the network through secondary devices (for example, an Ethernet tap)
•In a DLR network, you must configure at least one of the supervisor-capable devices as
the ring supervisor before physically closing the ring. A backup supervisor is
recommended in case of a supervisor fault.
•Run all nodes on the DLR network at 100 Mbps and in Full-duplex mode. These
configuration values provide the best performance. Otherwise, run all nodes in Auto-
Negotiate. Do not use Auto-Negotiate on one node and then force the baud rate on the
next node linked to it.
•Devices running at 10 Mbps should be connected through a network tap using the
device port. If you connect a 10 Mbps device directly to the network, instead of through
a tap, the linear or DLR network traffic slows to 10 Mbps. Additionally, if the 10 Mbps
device is connected to the network without a network tap, network recovery times are
significantly impacted.

EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 15
EIP-200S Ethernet/IP Adapter
2
Hardware configuration
See the separate manual "EIP ET200 Configuration Tool User Manual" for information on
the EIP ET200 Configuration Tool for the EIP-200S Ethernet/IP Adapter. The manual can be
found on the Companion Disk that shipped with the product, or downloaded from the
Siemens Service & Support Website (http://support.automation.siemens.com).
LED status indicators
The EIP-200S Ethernet/IP Adapter module has three bi-color LEDs that provide diagnostic
information about the current state of the device and provide an indication of any faults. The
LEDs conform to the behaviors defined in the ODVA Ethernet/IP Adaptation of CIP Adapter
Specification for the Module Status and Network Status LEDs, and in this manual for I/O
Status LEDs.
LED status indicator: Module Status LED
The bi-color Module Status LED indicates the current state of the EIP-200S Ethernet/IP
Adapter, as described in the following table:
State
Description
Off
No power applied to device.
Flashing green Device has not been configured.
Invalid parameter data.
Green Device has initialized successfully and no errors
were detected.
Flashing red Recoverable fault.
Device needs commissioning due to configuration
error:
•Invalid parameter data
•Invalid slot configuration data.
Red
Unrecoverable fault detected: hardware failure.

EIP-200S Ethernet/IP Adapter
EIP-200S Ethernet/IP Adapter Distributed I/O System
16 System Manual, 06/2018, A5E44345053-AB
LED status indicator: Network Status LED
The bi-color Network Status LED indicates the current state of the EIP-200S Ethernet/IP
Adapter communications link, as described in the following table:
State
Description
Off •Device is powered off, or is powered on but
does not have an IP address
•May be waiting for IP address if in
DHCP/BOOTP mode
Flashing green No connection - an IP address is configured, but
no CIP connections are established
Green
Connected
Flashing red One or more CIP connections have timed out
Red
Duplicate IP address detected
LED status indicator: I/O Status LED
The bi-color I/O Status LED provides diagnostic information about the current state of the I/O
under the control of the EIP-200S Ethernet/IP Adapter module, as described in the following
table:
State
Description
Off •All outputs and inputs are inactive
•Configuration errors prevent enabling of in-
puts/outputs
•No connection
•Device not powered
Green Device online with connections established (nor-
mal operation, RUN mode)
Flashing green
Firmware update in progress
Flashing red One or more outputs or inputs are faulted when
I/O is active
Installing the EIP-200S Ethernet/IP Adapter
The EIP-200S Ethernet/IP Adapter transfers data between ET 200S I/O modules and the
Ethernet/IP network. The "Installation" chapter provides information on installing the
components that make up an ET 200S distributed I/O system.
Refer to the section entitled "Installing the EIP-200S Ethernet/IP Adapter" for information on
installing and removing the EIP-200S Ethernet/IP Adapter.

EIP-200S Ethernet/IP Adapter
2.1 Operation
EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 17
2.1
Operation
Operating modes
The EIP-200S Ethernet/IP Adapter is a modular device capable of operating out of the box
without any special configuration software. However, to take full advantage of advanced
diagnostics and features, a configuration tool is required. The Companion Disk shipped with
this product contains both the Configuration Tool and the EIP ET200 Configuration Tool User
Manual.
The EIP-200S Ethernet/IP Adapter operates in one of two modes: automatic configuration
and user configured. The default mode, as shipped from the factory, is automatic
configuration mode.
Automatic configuration mode
When operating in automatic configuration mode, the EIP-200S Ethernet/IP Adapter
configures its I/O sizes, I/O module parameterization data, and configuration data according
to the combination of ET 200S modules present at power-up or reset. In automatic
configuration mode:
●Electronic module parameter data cannot be specified - the modules use the default
parameters. The user must make certain that the default parameters for the modules
satisfy the application requirements.
●I/O configuration cannot be verified - the EIP-200S Ethernet/IP Adapter is responsible for
verifying the configuration by examining I/O sizes.
Note that the EIP-200S Ethernet/IP Adapter module is unable to differentiate modules of
similar configuration types (for example, a 2 A discrete output module as compared to a
0.5 A discrete output module):
●The I/O data format is defined by the combination of modules installed.
●I/O module grouping is enabled.
●The I/O status byte is enabled.
Note
NAMUR and motor starters require user configured mode.

EIP-200S Ethernet/IP Adapter
2.1 Operation
EIP-200S Ethernet/IP Adapter Distributed I/O System
18 System Manual, 06/2018, A5E44345053-AB
User Configured Mode
When operating in user configured mode, the EIP-200S Ethernet/IP Adapter I/O sizes, I/O
module parameterization data, and I/O configuration data is stored in nonvolatile memory
and accessed via the Slot Object. In user configured mode:
●Electronic module parameter data can be modified, allowing access to more advanced
configuration options and diagnostics.
●I/O configuration is verified. Mismatching I/O configurations result in an error.
Note that the EIP-200S Ethernet/IP Adapter is unable to differentiate modules of similar
configuration types (for example, a 2 A discrete output module as compared to a 0.5 A
discrete output module):
●Slot Object instance attributes can be set, providing no I/O connections are open.
●The I/O data format is defined by the user by using the combination of modules
configured.
●I/O module grouping is available but must be specified by the configuration selections.
Note
The EIP ET200 Configuration Tool is suggested for configuration of a EIP
-200S
Ethernet/IP Adapter in user configured mode.
This tool is available on the Companion D
isk that shipped with the product, or via
download from the Siemens Service & Support Website
(
http://support.automation.siemens.com).
I/O status byte
The IO_StatusEnable attribute of the Adapter Object allows you to enable or disable the
generation of an additional I/O status byte to detect faults in the EIP-200S Ethernet/IP
Adapter. If the IO_StatusEnable attribute is TRUE (1), an additional status byte is placed at
the beginning of the input data packet, prior to any electronic module data. In the event of a
fault, the status byte is set to 1, and the I/O status LED flashed red while I/O is active.
If the IO_StatusEnable attribute is FALSE (0), the input data packet contains only electronic
module data as configured.
Configuration
Changes to user configuration data take effect immediately without resetting the device.
Changes to user configuration data are stored in nonvolatile memory and on the SD card
immediately (before the explicit message response is sent).
Module grouping
For more efficient use of address space and data transfer, the EIP-200S Ethernet/IP Adapter
supports the grouping of electronic module data. In AutoConfig mode, the electronic module
data is always grouped. See the topic entitled "Configuring the ET 200S" for details about
grouping of module data.

EIP-200S Ethernet/IP Adapter
2.1 Operation
EIP-200S Ethernet/IP Adapter Distributed I/O System
System Manual, 06/2018, A5E44345053-AB 19
Reset behavior
When the Adapter is reset, the outputs will be deactivated during the short period that the
reset is in progress. The unit can be reset in the following ways:
●Cycling of primary device 24 VDC power
●Using the reset capabilities in the Configuration Tool
●Sending an explicit Ethernet/IP Reset service message to instance 1 of the Identity
Object with service data of 0 or 1. If service data 1 is sent, on reset the module returns to
factory default state and any user configuration is lost.
Note
When network power is removed (or if an I/O connection times out or is lost), outp
uts will go
to their configured "substitute" value according to how this parameter is set for each I/O
module. The "default" substitute value, which will be in effect in automatic configuration
mode, will be to turn off or zero outputs. Consult the individ
ual manual for the specific I/O
module if this is a concern. To set a non
-default substitute value, user configuration MUST
be used.

EIP-200S Ethernet/IP Adapter
2.2 Parameters for the EIP-200S Ethernet/IP Adapter
EIP-200S Ethernet/IP Adapter Distributed I/O System
20 System Manual, 06/2018, A5E44345053-AB
2.2
Parameters for the EIP-200S Ethernet/IP Adapter
Parameter assignment
Parameters for the EIP-200S Ethernet/IP Adapter are set by using the ZNX-EIP-200S
Configuration Tool software. After loading new parameters into the interface module, the
parameters take effect immediately.
The following table describes the parameters of the interface module:
EIP-200S Ethernet/IP
Adapter IM
Value range
Default
Applicability
Interference frequency suppres-
sion
50 Hz / 60 Hz 60 Hz ET 200S
Reference junction slot
None / 2 to 63
None
ET 200S
Reference junction RTD on channel 0 /
RTD on channel 1
RTD on channel 0 ET 200S
Bus length
≤1 m / > 1 m
≤1m
ET 200S
Interference frequency suppression
The frequency of your alternating voltage system can affect measured values negatively,
particularly in the case of both measurements in small voltage ranges and thermocouples.
Specify here the dominant line frequency in your system (50 Hz or 60 Hz).
The interference frequency suppression parameter is valid for all analog electronic modules.
The integration time and conversion time of the individual modules are also set by means of
this parameter.
Bus length
The bus length parameter specifies the maximum width of the station backplane bus:
●≤1 m: the default setting for the maximum bus length is 1 m.
●> 1 m: the bus length of the ET 200S system is > 1 m and can be up to 2 m. However,
this setting will increase the response time of the ET 200S.