Siemens SIMATIC ET 200SP User manual

Manual
Digital output module DQ 4x24..230VAC/2A ST (6ES7132-6FD00-0BB1)
ET 200SP
02/2014Edition
Answers for industry.
SIMATIC

DQ 4x24..230VAC/2A ST
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
ET 200SP
DQ 4x24..230VAC/2A ST
digital output module
(6ES7132-6FD00-0BB1)
Manual
02/2014
A5E32043575
-AA
Preface
Guide to documentation
1
Product overview
2
Wiring
3
Parameter
assignment/addressing
4
Interrupts/diagnostics alarms
5
Technical specifications
6
Parameter data record
A

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32043575-AA
Ⓟ
02/2014 Technical data subject to change
Copyright © Siemens AG 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 3
Preface
Preface
Purpose of the documentation
This device manual complements the system manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293). Functions that generally
relate to the system are described in this manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the system.
Conventions
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product and on the section of the documentation to which particular attention
should be paid.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. You can find more information about industrial security on the Internet
(http://www.siemens.com/industrialsecurity).
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. You can find more information on the Internet
(http://support.automation.siemens.com).

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 4
Table of contents
Preface ................................................................................................................................................... 3
1 Guide to documentation .......................................................................................................................... 5
2 Product overview .................................................................................................................................... 7
2.1 Properties ...................................................................................................................................... 7
3 Wiring ..................................................................................................................................................... 9
3.1 Terminal assignment..................................................................................................................... 9
3.2 Block diagram ............................................................................................................................. 11
4 Parameter assignment/addressing........................................................................................................ 12
4.1 Parameters.................................................................................................................................. 12
4.2 Explanation of parameters .......................................................................................................... 13
4.3 Address space ............................................................................................................................ 14
5 Interrupts/diagnostics alarms................................................................................................................. 15
5.1 Status and fault displays ............................................................................................................. 15
5.2 Load voltage status ..................................................................................................................... 17
6 Technical specifications ........................................................................................................................ 18
6.1 Technical specifications .............................................................................................................. 18
A Parameter data record .......................................................................................................................... 21
A.1 Parameter assignment and structure of parameter data record................................................. 21

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 5
Guide to documentation
1
Introduction
The documentation for the SIMATIC products has a modular structure and covers topics
relating to your automation system.
The complete documentation for the ET 200SP distributed I/O system consists of a system
manual, function manuals and product manuals.
The STEP 7 information system (online help) also helps you to configure and program your
automation system.
Overview of the documentation for digital output module DQ 4×24..230VAC/2A ST
The table below lists additional documentation that you will need when using the
DQ 4×24..230VAC/2A ST digital output module.
Table 1- 1 Documentation for digital output module DQ 4×24..230VAC/2A ST
Topic
Documentation
Key content
System description System manual ET 200SP distributed
I/O system
(http://support.automation.siemens.co
m/WW/view/en/58649293)
•Application planning
•Installation
•Wiring
•Commissioning
Designing interference-
free controllers
Function manual Designing
interference-free controllers
(http://support.automation.siemens.co
m/WW/view/en/59193566)
•Basics
•Electromagnetic compatibility
•Lightning protection
System diagnostics Function manual Diagnostics
(http://support.automation.siemens.co
m/WW/view/en/59192926)
•Overview
•Diagnostics evaluation of
hardware/software
BaseUnits Manual ET 200SP BaseUnits
(http://support.automation.siemens.co
m/WW/view/en/59753521)
Technical specifications
Amendments and special
features of the ET 200SP
I/O system
ET 200SP Product information
(http://support.automation.siemens.co
m/WW/view/en/73021864)
Current information not yet
documented in the system
manuals, function manuals, or
other manuals.

Guide to documentation
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
6Manual, 02/2014, A5E32043575-AA
SIMATIC manuals
All of the current manuals for SIMATIC products are available for download free of charge
from the Internet (http://www.siemens.com/simatic-tech-doku-portal).

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 7
Product overview
2
2.1
Properties
Order number
6ES7132-6FD00-0BB1
View of the module
Figure 2-1 View of the DQ 4×24..230VAC/2A ST module

Product overview
2.1 Properties
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
8Manual, 02/2014, A5E32043575-AA
Properties
The module has the following technical properties:
●4 digital outputs each with a value status (quality information)
●Supply voltage L+
●Switches in zero point
●Output current 2 A per channel
●Total current 8 A (per module)
●Assignable substitute values (per channel)
●Substitute values (per channel)
●Suitable for solenoid valves, AC contactors, and indicator lights
The module supports the following functions:
●Firmware update
●Identification data I&M0 to I&M3
●Configuration in RUN
●PROFIenergy
You can configure the module with STEP 7 (TIA Portal) and with a GSD file.
Accessories
The following accessories must be ordered separately:
●Labeling strips
●Color identification labels
●Reference identification label
You can find additional information on the accessories in the ET 200SP Distributed I/O
System (http://support.automation.siemens.com/WW/view/en/58649293) system manual.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 9
Wiring
3
3.1
Terminal assignment
General pin assignment
NOTICE
Dangerous voltage. Risk of death or serious injury.
Prior to working on the system and module, always disconnect them from the power supply.
Note
Limiting overvoltage
You must ensure overvoltage is limited to 1 kV for the encoder supply.
Note
Power limitation
To limit power, each input voltage must have a fuse with a
maximum rating of 10 A tripping
current. The fuse must be a quick
-acting microfuse.

Wiring
3.1 Terminal assignment
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
10 Manual, 02/2014, A5E32043575-AA
Table 3- 1 Pin assignment for DQ 4×24..230VAC/2A ST
Pin assignment for DQ 4×24..230VAC/2A ST (6ES7132-6FD00-0BB1)
Terminal
Assign-
ment
Terminal
Assign-
ment
Description
BaseUnit
1
Color identification label
(terminals 1 to 12)
1
DQ0
2
DQ1
•DQn: Output signal,
channel n
•L1: Encoder supply 24 to 230
V AC2, 3
•N: Neutral 2
B1
CC41
6ES7193-6CP41-2MB0
3
DQ
2
4
DQ
3
5
L1
6
L1
7
L1
8
L1
9
N
10
N
11
N
12
N
1L
24...230 V
AC
1N
N
2L
24...230 V
AC
2N
N
Connection examples
1
BaseUnit types that can be used are identified by the last two digits of the order number. See also
"ET 200SP distributed I/O system" system manual.
2
L1, N: Supply terminals for the I/O module on this BU only
3
max. load current: max. permitted module current, depending on temperature derating, minus the total output current in
the application
No pin for
The digital output is not suitable for alternating current loads.

Wiring
3.2 Block diagram
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 11
3.2
Block diagram
Block diagram
Figure 3-1 Block diagram DQ 4×24..230VAC/2A ST

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 12
Parameter assignment/addressing
4
4.1
Parameters
DQ 4×24..230VAC/2A ST parameters
The following table lists the configurable parameters. The effective range of the configurable
parameters depends on the type of configuration. The following configurations are possible:
●Distributed operation on PROFINET IO in an ET 200SP system
●Distributed operation with PROFIBUS DP in an ET 200SP system
When performing the configuration in the user program, use the "WRREC" instruction to
transfer the parameters to the module using data records (refer to the section Parameter
assignment and structure of parameter data record (Page 21)).
The following parameter settings are possible:
Table 4- 1 Configurable parameters and their defaults (GSD file)
Parameters
Value range
Default
Reconfiguration
in RUN
Effective range with configuration
software, e.g. STEP 7 (TIA Portal)
GSD file
PROFINET IO
GSD file
PROFIBUS DP1
Operating mode •Channel activated
•Channel deactivated
Channel
activated
Yes Channel Channel
Reaction to CPU
STOP
•Turn off
•Keep last value
•Output substitute
value 1
Turn off Yes Channel Module
1
Only for configuration using the PROFIBUS GSD file; does not affect configuration with STEP 7 using HSP: As the
number of parameters with PROFIBUS GSD configuration is limited to a maximum of 244 bytes per ET 200SP station,
the configuration options are limited. If required, however, you can still set this parameter using data record 128 as
described in the column "GSD file PROFINET IO" (see the table above). The parameter length of the I/O module is 3
bytes.

Parameter assignment/addressing
4.2 Explanation of parameters
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 13
4.2
Explanation of parameters
Operating mode
Determines whether a channel is enabled or disabled.
Reaction to CPU STOP
Determines the behavior of the module in the event of a CPU STOP.
See also
ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293)

Parameter assignment/addressing
4.3 Address space
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
14 Manual, 02/2014, A5E32043575-AA
4.3
Address space
Configuration options with the DQ 4×24..230VAC/2A ST
The following configurations are possible:
●Configuration 1: Without value status
●Configuration 2: With value status
Evaluating the value status
An additional byte is allocated in the input address space if you enable the value status for
the digital module. Each bit in this byte is assigned to a channel and returns information on
the validity of the digital value (0 = incorrect value).
Address space of the digital output module DQ 4×24..230VAC/2A ST
The following figure shows the assignment of address space for the
DQ 4×24..230VAC/2A ST with value status (Quality Information (QI)). The addresses for the
value status are only available if the value status is enabled.
Figure 4-1 Address space of the DQ 4×24..230VAC/2A ST digital output module with value status

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 15
Interrupts/diagnostics alarms
5
5.1
Status and fault displays
LED displays
The figure below shows the LED displays (status and fault displays) of the
DQ 4×24..230VAC/2A ST.
①
DIAG (green/red)
②
Channel status (green)
③
PWR (green)
Figure 5-1 LED display

Interrupts/diagnostics alarms
5.1 Status and fault displays
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
16 Manual, 02/2014, A5E32043575-AA
Meaning of the LEDs
The tables below explain the meaning of the status and fault displays.
LED DIAG
Table 5- 1 LED DIAG fault display
LED DIAG
Meaning
Off
Backplane bus supply of the ET 200SP not OK
Flashing
Module parameters not assigned
On
Module configured and no module diagnostics
Flashing
Module configured and module diagnostics
LED channel status
Table 5- 2 LED channel status display
LED channel
status
Meaning
Off
Channel deactivated or activated and process signal = 0
On
Channel activated and process signal = 1
LED PWR
Table 5- 3 LED PWR status display
LED PWR
Meaning
Off
Supply voltage L+ missing
On
Supply voltage L+ present

Interrupts/diagnostics alarms
5.2 Load voltage status
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 17
5.2
Load voltage status
Load voltage status
The firmware of the module cannot detect the status of the load voltage.
If the "Load voltage status" function tied to the server module is used, a "1" is always
displayed in the status bit for a slot with the DQ 4×24..230VAC/2A ST. Even when the load
voltage is not applied.
The state of the load voltage at the terminal does not impact the PROFIenegy behavior.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 18
Technical specifications
6
6.1
Technical specifications
DQ 4×24...230VAC/2A ST technical specifications
6ES7132-6FD00-0BB1
General information
Usable BaseUnits
BU type B1
Product function
I&M data
Yes; I&M0 to I&M3
Engineering with
STEP 7 TIA Portal can be
configured/integrated
as of version
V13 / V13
STEP 7 can be configured/integrated as of version
V5.5 SP3 / V5.5 SP4
PROFIBUS as of GSD version/GSD revision
GSD as of revision 5
PROFINET as of GSD version/GSD revision
V2.3 / -
Supply voltage
Rated value (AC)
230 V
Input current
Current consumption (rated value)
11.5 mA
Current consumption, max.
13 mA
Power loss
Power loss, typ.
9 W; active power, load voltage 230 V, all outputs
loaded with 2 A, 50 Hz
Address area
Address space per module
Address space per module, max.
1 byte; + 1 byte for QI information
Output
1 bytes
Digital outputs
Number of outputs
4
Switching to M potential
No
Switching to P potential
Yes
Short
-circuit protection No; install a fuse with 10A trigger current when
using a type B1 BU
Wire-break detection
No
Overload protection
No; install a fuse with 10A trigger current when
using a type B1 BU
Limitation of inductive shutdown voltage to
Install overvoltage protection when using a type
B1 BU
Controlling a digital input
Yes

Technical specifications
6.1 Technical specifications
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 02/2014, A5E32043575-AA 19
6ES7132-6FD00-0BB1
Switching capacity of outputs
With resistive load, max.
2 A
With lamp load, max.
100 W
Output voltage
for signal "1", min.
20.4 V
Output current
for signal "1" rated value
2 A
for signal "1" permissible range, min.
10 mA
For signal "1" permitted range, max.
2 A
for signal "0" residual current, max.
460 µA
Output delay with resistive load
"0" to "1", max.
10 ms
"1" to "0", max.
10 ms
Parallel switching of 2 outputs
For logical operations
No
For increased performance
No
For
redundant control of a load Yes
Switching frequency
With resistive load, max.
10 Hz
With inductive load, max.
0.5 Hz
With lamp load, max.
1 Hz
Total current of the outputs
Max. current per channel
2 A
Max. current per module
8 A
Total current of the outputs (per module)
Horizontal installation
•
up to 40 °C, max. 8 A
•
up to 50 °C, max. 6 A
•
up to 60 °C, max. 4 A
Vertical installation
•
up to 30 °C, max. 8 A
•
up to 40 °C, max. 6 A
•
up to 50 °C, max. 4 A
Output current per channel
Horizontal installation
•
up to 60 °C, max. 2 A
Vertical installation
•
up to 50 °C, max. 2 A
Triac outputs
Size of motor starter according to NEMA, max.
5