Siemens EA12 User manual

Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com
SM
View
Instra

SIMADYN D
Digital Control System
I/O module EA12
User Manual
Edition 05.95 DK-Nr. 232241
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

User Manual, I/O module EA12
Edition Edition status
1I/O module EA12 06.93
2I/O module EA12 05.95
Copying of this document and giving it to others and the use or
communication of the contents thereof is forbidden without express
authority. Offenders are liable to the payment of damages. All rights
are reserved in the event of the grant of a patent or the registration of
a utility model or design.
We have checked the contents of this Manual to ensure that they
coincide with the described hardware and software. However,
deviations cannot be completely ruled-out, so we cannot guarantee
complete conformance. However, the information in this document is
regularly checked and the necessary corrections included in
subsequent editions. We are thankful for any recommendations or
suggestions.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Contents
Siemens AG Dk-Nr. 232241 Edition 05.95
SIMADYN D Hardware User Manual
Contents
Warning information........................................................................................................................ 1
1. Description.................................................................................................................................. 3
2. Module construction.................................................................................................................... 3
3. Notes for the user........................................................................................................................ 4
4. Technical specification................................................................................................................ 5
5. Connector pin assignments of X5................................................................................................ 6
6. STRUC-L menu of the EA12 module in the master program....................................................... 7
7. Miscellaneous............................................................................................................................. 7
7.1. Appendices.................................................................................................................. 7
7.1.1. Figures.......................................................................................................... 7
7.1.2. Drawings....................................................................................................... 8
7.1.2.1. Block diagram....................................................................................... 8
7.1.2.2. Dimension drawing and table of connectors.......................................... 8
7.1.2.3. Location diagram.................................................................................. 8
8. ECB instructions.......................................................................................................................... 9
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Warning information
Edition 05.95 Siemens AG Dk-Nr. 232241
SIMADYN D Hardware User Manual
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Warning information
Siemens AG Dk-Nr. 232241 Edition 05.95 1
SIMADYN D Hardware User Manual
N O T E !
The information in this Manual does not purport to cover all details or variations in equipment, nor to provide
for every possible contingency to be met in connection with installation, operation or maintenance.
Should further information be desired or should particular problems arise which are not covered sufficiently for
the purchaser’s purposes, please contact your local Siemens office.
Further, the contents of this Manual shall not become a part of or modify any prior or existing agreement,
committment or relationship. The sales contract contains the entire obligation of Siemens. The warranty
contained in the contract between the parties is the sole warranty of Siemens. Any statements contained
herein do not create new warranties nor modify the existing warranty.
Warning information
W A R N I N G !
Electrical equipment has components which are at dangerous voltage levels.
If these instructions are not strictly adhered to, severe bodily injury and material
damage can result.
Only appropriately qualified personnel may work on this equipment or in its
vicinity.
This personnel must be completely knowledgeable about all the warnings and
service measures according to this User Manual.
The successful and safe operation of this equipment is dependent on proper
handling, installation, operation and maintenance.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Warning information
2Edition 05.95 Siemens AG Dk-Nr. 232241
SIMADYN D Hardware User Manual
Definitions
*QUALIFIED PERSONNEL
For the purpose of this User Manual and product labels, a „Qualified person“ is someone who is familiar with the
installation, mounting, start-up and operation of the equipment and the hazards involved. He or she must have
the following qualifications:
1. Trained and authorized to energize, de-energize, clear, ground and tag circuits and equipment in accordance
with established safety procedures.
2. Trained in the proper care and use of protective equipment in accordance with established safety
procedures.
3. Trained in rendering first aid.
*DANGER
For the purpose of this User Manual and product labels, „Danger“ indicates death, severe personal injury and/or
substantial property damage will result if proper precautions are not taken.
*WARNING
For the purpose of this User Manual and product labels, „Warning“ indicates death, severe personal injury or
property damage can result if proper precautions are not taken.
*CAUTION
For the purpose of this User Manual and product labels, „Caution“ indicates that minor personal injury or
material damage can result if proper precautions are not taken.
*NOTE
For the purpose of this User Manual, „Note“ indicates information about the product or the respective part of the
User Manual which is essential to highlight.
C A U T I O N !
This board contains components which can be destroyed by electrostatic
discharge. Prior to touching any electronics board, your body must be electrically
discharged. This can be simply done by touching a conductive, grounded object
immediately beforehand (e.g. bare metal cabinet components, socket protective
conductor contact).
W A R N I N G !
Hazardous voltages are present in this electrical equipment during operation.
Non-observance of the safety instructions can result in severe personal injury or
property damage.
It is especially important that the warning information in all of the relevant
Operating Instructions are strictly observed.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Description
Siemens AG Dk-Nr. 232241 Edition 05.95 3
SIMADYN D Hardware User Manual
1. Description
The external EA12 module is used in the SIMADYN D system for outputting analog voltage signals
(-10 to +10V, accuracy: 14 bits or 1mV).
The addresses of these analog outputs are assigned by a programmable address decoder dependent
on the slot.
The EA12 module has 8 channels. The signal outputs are routed to the 20-way ribbon cable
connector X5. In addition to the 8 signals there is one ground terminal for each and, in addition, two
ground and two shield pins.
The signals can also be tapped at the double test sockets (dia. = 2.3 mm, one socket each for signal
and ground) e.g. on system startup.
The outputs can be loaded with up to 10 mA and are proof against short circuit up to a period of 120
sec.
Caution: the total signal load at connector X5 and the associated double test socket must not exceed
10 mA.
The output format for the individual channels can be configured. This is done by specifying a
multiplication factor in powers of 2 (extra for each channel).
The 50-pin ribbon cable connector X6 can be ignored, if at all available on the frontplate.
2. Module construction
- 1 plug-in station (corresponds to 1 1/3 SPS )
- SIMADYN D local bus connection
- Programmable address decoder (PAD) with module identification
- 8 analog output channels with D/A converters, -10 to +10 V, 10 mA, 14-bit accuracy (corresponding
to 1 mV)
- Connection option for KO via 2.3 mm test sockets
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Notes for the user
4Edition 05.95 Siemens AG Dk-Nr. 232241
SIMADYN D Hardware User Manual
3. Notes for the user
The external EA12 module can be used both in all SIMADYN D subracks, in each connected to the
local bus. Each module takes up one plug-in station in the subrack.
The module can only function properly when it is screwed down in position
in the subrack (also during commissioning).
If the module is plugged onto an adapter, the frontplate (or even better, one of the two metallized
frontplate end pieces) must be connected to chassis via a short lead in order to have the shield
potential at X5/17/18.
Because of the type of power supply module used (switched-mode power supply), noise with voltage
spikes of up to 100 mV can be measured at the analog outputs. This is caused by surges/dips on the
M (0V reference potentials) bus and can be eliminated by installing an input filter at the signal
destination and keeping the given min. load (see technical data).
The eight output voltages of the module are adjusted for minimum offset and correct gain at an
ambient temperature of about 20°C. The offset determines how high the output voltage is for a
software value corresponding to 0 V. The gain adjustment however determines how high the output
voltage is for a software valu&e corresponding to ±10 V.
The two potentiometers required per output for this purpose have not been locked so that any
necessary adjustments can be made later in operation (ambient temperature, accuracy
specifications). The guide value for temperature sensitivity is ±240 uV at a temperature change of ±
1 deg.
The following table shows the assignment of potentiometers (-Rxx) to outputs:
EA12 outputs Connector Offset Gain
Output 1 X5 A -R49 -R46
Output 2 X5 B -R55 -R52
Output 3 X5 C -R61 -R58
Output 4 X5 D -R67 -R64
Output 5 X5 E -R73 -R70
Output 6 X5 F -R79 -R76
Output 7 X5 G -R85 -R82
Output 8 X5 H -R91 -R88
Before adjustment the module must have reached operation temperature (min. 2 minutes with
operation voltage).
When making adjustments, always start with the offset. To do this, the respective output should be
set to zero volts (software). The deviation of the output voltage from the desired zero volts is
corrected by turning the setting screw of the appropriate offset potentiometer. Rotation in the
clockwise direction changes the output voltage in the direction of +10 V.
When the offset adjustment has been made, the gain is adjusted with a software value of +10V at the
respective output. Deviation of the output voltage from the desired 10 V is corrected by turning the
adjusting screw of the respective gain potentiometer. Rotation against the clockwise direction
changes the output voltage in the direction of -10 V.
The analog outputs are connected via the SE7.1 interface module, which is snapped onto the
mounting rack. Another connection can be made by the SE40 interface module (one-to-one
connection of the ribbon cable connector pins to screw-type terminals).
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Technical specification
Siemens AG Dk-Nr. 232241 Edition 05.95 5
SIMADYN D Hardware User Manual
Connector X5 on the output module and connector X1 on the interface module are interconnected by
a 20-way ribbon cable (Recommended: SC12 ribbon cable with twisted pairs).
The appropriate circuit diagram is shown in figure 1, appendix.
The SE7.1 interface module has a screw-type terminal for signal, ground and shield for each channel;
the shield is not connected to the SIMADYN D chassis potential.
Additional components that can be used:
Ribbon cable
* 20-way, twisted pairs, 1.5 m SC12 6DD 1684-0BC0
* 20-way, 2.0 m SC11 6DD 1684-0BB0
Interface modules
* SE7.1 6DD 1681-0AH1
I/O block, analog, 8/10 channel
* SE40 6DD 1681-0EA0
Terminal block, 20-way, one-to-one
4. Technical specification
GENERAL
INSULATION GROUP B to VDE 0110 paragraph 13, group 2 at 15V,
15 V DC
AMBIENT TEMPERATURE 0 to 55 deg. C, with self ventilation
STORAGE TEMPERATURE -40 to +70 deg. C
PROTECTION CLASS IP00 to DIN 40050
HUMIDITY CLASS F to DIN 40040
ALTITUDE RATING S to DIN 40040
MECHANICAL STRESS Installation in stationary equipment,
sensitive to vibrations
PACKAGING SYSTEM ES 902 C
DIMENSIONS 233.4 x 220 mm
MODULE WIDTH 1 1/3 SPS = 1 plug-in station = 20.14 mm
WEIGHT 0.5 kg
CURRENT CONSUMPTION P5 0.6 A
P15 0.2 A
N15 O.2 A
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Connector pin assignments of X5
6Edition 05.95 Siemens AG Dk-Nr. 232241
SIMADYN D Hardware User Manual
ANALOG OUTPUTS
NUMBER 8
MIN. OUTPUT VOLTAGE -10 V
MAX. OUTPUT VOLTAGE +10 V
MAX. CURRENT ±10 mA
MIN. CURRENT (REC ±5 mA (at ±10 V)
ACCURACY 14 bits (corr. to 1 mV)
LINEARITY ERROR
ABSOLUT ±0.6 mV
DIFFERENTIAL ±1 mV
MONOTONY 14 bits (corr. to 1 mV)
DRIFT
OFFSET 240 uV/deg
GAIN 240 uV/deg (deviation of max. output value)
SHORT-CIRCUIT PROTECTION Ohmic resistance 56 ohm
MAX. SHORT-CIRCUIT DURATION 120 sec.
TOTAL LOAD All outputs simultaneously, 10 mA
5. Connector pin assignments of X5
Pin EA12 Connector Relevant test socket
1Output 1 X5 A X11 SIG
2Ground X5 A X11 COM
3Output 2 X5 B X12 SIG
4Ground X5 B X12 COM
5Output 3 X5 C X13 SIG
6Ground X5 C X13 COM
7Output 4 X5 D X14 SIG
8Ground X5 D X14 COM
9Output 5 X5 E X15 SIG
10 Ground X5 E X15 COM
11 Output 6 X5 F X16 SIG
12 Ground X5 F X16 COM
13 Output 7 X5 G X17 SIG
14 Ground X5 G X17 COM
15 Output 8 X5 H X18 SIG
16 Ground X5 H X18 COM
17 Shield X5 ---
18 Shield X5 ---
19 Shield X5 ---
20 Shield X5 ---
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

STRUC-L menu of the EA12 module in the master program
Siemens AG Dk-Nr. 232241 Edition 05.95 7
SIMADYN D Hardware User Manual
6. STRUC-L menu of the EA12 module in the master program
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
:EA12 "analog output module 2, L-bus"
ISE 1C = N "ignore failed message (RDYINT) (Y/N) ?"
X5A 1K > "D/A converter 1, X11"
X5B 1K > "D/A converter 2, X12"
X5C 1K > "D/A converter 3, X13"
X5D 1K > "D/A converter 4, X14"
X5E 1K > "D/A converter 5, X15"
X5F 1K > "D/A converter 6, X16"
X5G 1K > "D/A converter 7, X17"
X5H 1K > "D/A converter 8, X18"
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
See also description of master program
7. Miscellaneous
7.1. Appendices
7.1.1. Figures
- X 5
- X 6
EA12
- X 1
20
type of cable: SC12 (twisted pair)
Externe Anschlüsse
external connections
Kabeltyp: SC12 (paarweise verdrillt)
Figure 1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Miscellaneous
8Edition 05.95 Siemens AG Dk-Nr. 232241
SIMADYN D Hardware User Manual
7.1.2. Drawings
7.1.2.1. Block diagram
Block diagram: 3GE 465 642 9012.00 SU
7.1.2.2. Dimension drawing and table of connectors
Dimension drawing, front plate and table of
connectors used 3GE 465 642 9012.00 MB
7.1.2.3. Location diagram
Location diagram 3GE 465 642.9012.00 A0
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

ECB instructions
Siemens AG Dk-Nr. 232241 Edition 05.95 9
SIMADYN D Hardware User Manual
8. ECB instructions
Components which can be destroyed by electrostatic discharge (ECB)
Generally, electronic boards should only be touched when absolutely necessary.
The human body must be electrically discharged before touching an electronic board. This can be
simply done by touching a conductive, grounded object directly beforehand (e.g. bare metal cubicle
components, socket outlet protective conductor contact.
Boards must not come into contact with highly-insulating materials - e.g. plastic foils, insulated
desktops, articles of clothing manufactured from man-made fibers.
Boards must only be placed on conductive surfaces.
When soldering, the soldering iron tip must be grounded.
Boards and components should only be stored and transported in conductive packaging (e.g.
metalized plastic boxes, metal containers).
If the packing material is not conductive, the boards must be wrapped with a conductive packing
material, e.g. conductive foam rubber or household aluminum foil.
The necessary ECB protective measures are clearly shown in the following diagram.
a = Conductive floor surface d = ECB overall
b = ECB table e = ECB chain
c = ECB shoes f = Cubicle ground connection
Seated Standing Standing/sitting
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

ECB instructions
10 Edition 05.95 Siemens AG Dk-Nr. 232241
SIMADYN D Hardware User Manual
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

ECB instructions
Siemens AG Dk-Nr. 232241 Edition 05.95 11
SIMADYN D Hardware User Manual
Drives and Standard Products
Motors and Drives Systems Group
Postfach 3269, D-91050 Erlangen System-Based Technology
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com
SM
View
Instra