Siemens SIMATIC ET 200S User manual

RGB ELEKTRONIKA AGACIAK CIACIEK
SPÓŁKA JAWNA
Jana Dlugosza 2-6 Street
51-162 Wrocław
Poland
[e-mail]
[phone]
www.rgbautomatyka.pl
www.rgbelektronika.pl
DATASHEET
www.rgbautomatyka.pl
www.rgbelektronika.pl
OTHER SYMBOLS:
6ES7 151-1AA04-0AB0
SIEMENS

YOUR
PARTNER IN
MAINTENANCE
At our premises in Wrocław, we have a fully equipped servicing facility. Here we perform all the repair
works and test each later sold unit. Our trained employees, equipped with a wide variety of tools and
having several testing stands at their disposal, are a guarantee of the highest quality service.
OUR SERVICES
ENCODERS
SERVO
DRIVERS
LINEAR
ENCODERS
SERVO AMPLIFIERS
CNC
MACHINES
MOTORS
POWER
SUPPLIERS
OPERATOR
PANELS
CNC
CONTROLS
INDUSTRIAL
COMPUTERS
PLC
SYSTEMS
Repair this product with RGB ELEKTRONIKA ORDER A DIAGNOSIS ∠
Buy this product at RGB AUTOMATYKA BUY ∠

Preface, Contents
Product Overview 1
Brief Instructions on
Commissioning ET 200S 2
Configuration Options 3
Installation 4
Wiring and Fitting 5
Commissioning and Diagnostics 6
General Technical Specifications 7
Interface Modules 8
Terminal Modules 9
Power Modules 10
Digital Electronic Modules 11
Analog Electronic Modules 12
4 IQ-SENSE 13
RESERVE Modules 14
Appendices
Glossary, Index
Edition 12/2004
EWA-4NEB 780602402-12
ET 200S
Distributed I/O System
Manual
SIMATIC
This manual is part of the documentation
package with the order number
6ES7151-1AA10-8BA0
The following supplement is part of this documentation:
No. Designation Drawing number Edition
1 Product Information A5E00352937-02 01/2005
2 Product Information A5E00437368-01 04/2005

!Danger
indicatesthat death, severe personal injury or substantial property damage will result if proper precautions
are not taken.
!Warning
indicates that death, severe personal injury or substantial property damage can result if proper
precautions are not taken.
!Caution
indicates that minor personal injury can result if proper precautions are not taken.
Caution
indicates that property damage can result if proper precautions are not taken.
Notice
draws your attention to particularly important information on the product, handling the product, or to a
particular part of the documentation.
Qualified Personnel
Only qualified personnel should be allowed to install and work on this equipment. Qualified persons are
defined as persons who are authorized to commission, to ground and to tag circuits, equipment, and
systems in accordance with established safety practices and standards.
Correct Usage
Note the following:
!Warning
This device and its components may only be used for the applications described in the catalog or the
technical description, and only in connection with devices or components from other manufacturers which
have been approved or recommended by Siemens.
This product can only function correctly and safely if it is transported, stored, set up, and installed
correctly, and operated and maintained as recommended.
Trademarks SIMATIC, SIMATIC HMIand SIMATIC NETare registered trademarks of SIEMENS AG.
Third parties using for their own purposes any other names in this document which refer to trademarks
might infringe upon the rights of the trademark owners.
Safety Guidelines
This manual contains notices intended to ensure personal safety, as well as to protect the products and
connected equipment against damage. These notices are highlighted by the symbols shown below and
graded according to severity by the following texts:
We have checked the contents of this manual for agreement
with the hardware and software described. Since deviations
cannot be precluded entirely, we cannot guarantee full
agreement. However, the data in this manual are reviewed
regularly and any necessary corrections included in
subsequent editions. Suggestions for improvement are
welcomed.
Disclaimof LiabilityCopyright Siemens AG 2004 All rights reserved
The reproduction, transmission or use of this document or its
contents is not permitted without express written authority.
Offenderswill be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or
design,are reserved.
Siemens AG
Bereich Automation and Drives
Geschaeftsgebiet Industrial Automation Systems
Postfach 4848, D-90327 Nuernberg SiemensAG 2004
Technical data subject to change.
Siemens Aktiengesellschaft EWA-4NEB 780602402-12

iii
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
Preface
Purpose of the Manual
The information in this manual is intended to enable you to operate the ET 200S
Distributed I/O System
•as a DP slave on the PROFIBUS DP
•as a PROFINET I/O device on PROFINET
Required level of knowledge
Knowledge of the field of automation engineering is required to understand the
manual.
Scope of the manual
This manual is valid for the components of the ET 200S distributed I/O system
specified in Appendix A.
This manual contains a description of the components that were valid at the time
the manual was published. We reserve the right to enclose a Product Information
bulletin containing up-to-date information about new components and new versions
of components.
Changes since the previous version
The following changes/additions have been made since the previous version of the
manual:
•enhanced functions in the IM151-1 STANDARD and IM151-1 FO STANDARD
interface modules
•4AI I 2WIRE Standard analog electronic module added

Preface
iv
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
Certification
See Section 7.1 Standards, certificates and approvals
CE Mark of Conformity
See Section 7.1 Standards, certificates and approvals
Identification for Australia (C-tick mark)
See Section 7.1 Standards, certificates and approvals
Standards
See Section 7.1 Standards, certificates and approvals

Preface
v
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
Position in the information landscape
The following list shows a summary of the documentation packages or manuals
for the ET 200S:
• Installing and wiring the ET 200S
• Commissioning and
diagnostics for the ET 200S
• Technical specifications of the
IM151-1, digital
and analog electronic modules
• Order numbers for the ET 200S
ET 200S distributed
I/O system
ET 200S
Process-Related
Functions
• 1Count 24V/100kHz
• 1Count 5V/500kHz
• 1SSI
• 2PULSE
ET 200S IM151-7 CPU interface module
and operation list
SIMATIC ET 200S motor starter
fail-safe motor starter
SIGUARD safety equipment
• Installing and wiring
motor starters
• Commissioning and
diagnostics for motor starters
• Technical specifications
of motor starters
• Fail-Safe Motor Starter
• Safety-integrated SIGUARD
• Order numbers for motor starters
• Addressing of the IM151-7 CPU
• ET 200S with IM151-7 CPU in the
PROFIBUS network
• Commissioning and diagnostics for the
IM151-7 CPU
• Technical specifications of the IM151-7 CPU
ET 200S Positioning
• EM 1STEP 5V/204kHz
• 1POS INC/Digital
• 1POS SSI/Digital
• 1POS INC/Analog
• 1POS SSI/Analog
ET 200S serial interfaces
and modules
• 1SI 3964/ASCII
• 1SI MODBUS/USS
6ES7151-1AA10-8xA0
1)
1
)
x = language designation for order numbers
The documentation packages or manuals can only be ordered in German and English. In addition, French, Spanish and Italian
are available in the Internet (see Service & Support in the Internet)
PROFINET
System -
Description
• Basics
of PROFINET
• Network components
and structures
• Data interchange
and
communication
• PROFINET
Engineering
From PROFIBUS
DP to PROFINET IO
• Differences
• Blocks
• System
status lists
• Diagnostics
ET 200S FC frequency
converter
Operating manual
• Installation
• Commissioning
• Control and regulation processes
• Protection and monitoring functions
• Technical specifications
ET 200S FC frequency
converter
list manual
• Parameter list
• Function plans
• Interrupts,
error messages

Preface
vi
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
Note
The ET 200S distributed I/O system manual is included in the
ET 200S FC frequency converter documentation package.
The fail-safe modules are described in the
ET 200S distributed I/O system fail-safe modules manual. This manual and other
manuals for the fail-safe modules can be downloaded from the Internet.
A documentation overview for implementation of the ET 200S as an I/O device is
given below.
PROFINET
PROFINET System Description
Network components SIMATIC S7 and ET 200
Documentation for SIMATIC NET
Documentation for the switches
(e.g. SCALANCE)
Documentation for the IE/PB Link
Integration of PCs
Documentation for the CP 1616
Documentation for SOFTNET PNIO
Documentation for
industrial communications with
programming device/PC
Component-based Automation
Documentation for
Component-based Automation
Documentation for SIMATIC iMap
STEP 7
Documentation for STEP 7
Documentation for NCM
Documentation for CPU 31x3 PN/DP
Documentation for the CPs:
443-1 Advanced and
331-1 Advanced
From PROFIBUS DP to PROFINET IO
You are reading this documentation now:
Documentation for ET 200S

Preface
vii
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
Guide
You can quickly access specific information in the manual by using the following
aids:
•At the start of the manual you will find a complete table of contents and a list of
the diagrams and tables that appear in the manual.
•An overview of the contents of each section is provided in the left-hand column
on each page of each chapter.
•Following the appendices, you will find a glossary in which important technical
terms used in the manual are defined.
•At the end of the manual you will find a comprehensive index enabling rapid
access to the information you are looking for.
•Language identification for the order numbers of the manuals, for example,
6ES7 151-1AA10-8xA0
x is for : A = German,
B = English
Special note
In addition to this manual, you will also need the manual for the DP master or
PROFINET I/O controller (see Appendix A).
Note
You will find a complete list of the contents of the ET 200S manuals in Section1.4
of this manual. We recommend that you begin by reading this section so as to find
out which parts of which manuals are most relevant to you in helping you to do
what you want to do.
Recycling and disposal
Due to the fact that it is low in contaminants, the ET 200S is recyclable. Contact a
certified electronic-waste disposal company to recycle and dispose of your old
equipment in an environmentally-friendly manner.

Preface
viii
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
Contact persons
See product information Technical Support, Contact Persons and Training
Training
See product information Technical Support, Contact Persons and Training
SIMATIC Technical Support
See product information Technical Support, Contact Persons and Training
Service & Support on the Internet
See product information Technical Support, Contact Persons and Training