Siemens SIMATIC ET 200SP User manual

CPU 1510SP F-1 PN
(6ES7510-1SJ00-0AB0)
___________________
___________________
___________________
___________________
___________
___________________
___________________
SIMATIC
ET 200SP
CPU 1510SP F-1 PN
(6ES7510-1SJ00-0AB0)
Manual
12/2014
A5E35264953
-AA
Preface
Documentation guide
1
Product overview
2
Wiring
3
Interrupts, error messages,
diagnostics and system
alarms
4
Technical specifications
5
Dimension drawing
A

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E35264953-AA
Ⓟ
12/2014 Subject to change
Copyright © Siemens AG 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CPU 1510SP F-1 PN (6ES7510-1SJ00-0AB0)
4Manual, 12/2014, A5E35264953-AA
Preface
Purpose of the documentation
This manual supplements the ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293) system manual as well as
the function manuals. All system-wide functions are described in the system manual and in
the function manuals.
The information provided in this manual and the system manual allows you to commission
the CPU 1510SP F-1 PN.
The creation of the safety program and activation of safety operation are described in the
configuration and programming manual SIMATIC Safety - Configuring and Programming
(http://support.automation.siemens.com/WW/view/en/54110126).
Conventions
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
When this device manual refers to the CPU 1510SP-1 PN, we are actually referring to the
CPU 1510SP F-1 PN.
Please also observe the notes marked as follows:
Note
A note contains important information on the product described in the documentation, on
handling the product or on the part of the documentation to which particular attention should
be paid.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. You can find more information about industrial security on the Internet
(http://www.siemens.com/industrialsecurity).
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. You can find more information on the Internet
(http://support.automation.siemens.com).

CPU 1510SP F-1 PN (6ES7510-1SJ00-0AB0)
Manual, 12/2014, A5E35264953-AA 5
Table of contents
Preface ................................................................................................................................................... 4
1 Documentation guide .............................................................................................................................. 6
2 Product overview .................................................................................................................................... 8
2.1 Operating principle....................................................................................................................8
2.2 Properties..................................................................................................................................9
2.3 Differences between F-CPU 1510SP F-1 PN and standard CPU 1510SP-1 PN...................12
2.4 Operating and display elements .............................................................................................14
2.4.1 Front view of the module with BusAdapter .............................................................................14
2.5 Mode switch ............................................................................................................................15
2.6 Functions ................................................................................................................................15
2.6.1 PROFINET IO .........................................................................................................................15
2.6.2 PROFIenergy ..........................................................................................................................16
2.6.3 PROFIBUS DP........................................................................................................................17
2.6.4 Memory reset ..........................................................................................................................18
2.6.5 Restoring the factory settings of the CPU...............................................................................19
3 Wiring ................................................................................................................................................... 22
4 Interrupts, error messages, diagnostics and system alarms................................................................... 27
4.1 Status and error display of the CPU .......................................................................................27
5 Technical specifications ........................................................................................................................ 30
5.1 Technical specifications..........................................................................................................30
A Dimension drawing ............................................................................................................................... 40

CPU 1510SP F-1 PN (6ES7510-1SJ00-0AB0)
6Manual, 12/2014, A5E35264953-AA
Documentation guide
1
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
Basic information
The system manual describes in detail the configuration, installation, wiring and
commissioning of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help
supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, terminal diagrams, characteristics and technical specifications.
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, designing
interference-free controllers.
You can download the documentation free of charge from the Internet
(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-
overview/tech-doc-et200/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.

Documentation guide
CPU 1510SP F-1 PN (6ES7510-1SJ00-0AB0)
Manual, 12/2014, A5E35264953-AA 7
Manual Collection ET 200SP
The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(http://support.automation.siemens.com/WW/view/en/84133942).
My Documentation Manager
The My Documentation Manager is used to combine entire manuals or only parts of these to
your own manual.
You can export the manual as PDF file or in a format that can be edited later.
You can find the My Documentation Manager on the Internet
(http://support.automation.siemens.com/WW/view/en/38715968).
Applications & Tools
Applications & Tools supports you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus in individual products.
You can find Applications & Tools on the Internet
(http://support.automation.siemens.com/WW/view/en/20208582).
CAx Download Manager
The CAx Download Manager is used to access the current product data for your CAx or CAe
systems.
You configure your own download package with a few clicks.
In doing so you can select:
●Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
●Manuals, characteristics, operating manuals, certificates
●Product master data
You can find the CAx Download Manager on the Internet
(http://support.automation.siemens.com/WW/view/en/42455541).
TIA Selection Tool
With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).

CPU 1510SP F-1 PN (6ES7510-1SJ00-0AB0)
8Manual, 12/2014, A5E35264953-AA
Product overview
2
2.1
Operating principle
The CPU includes the operating system and executes the user program. The user program
is located on the SIMATIC memory card and is processed in the CPU work memory.
The PROFINET interfaces available on the CPU enable simultaneous communication with
PROFINET devices, PROFINET controllers, HMI devices, programming devices, other
controllers and additional systems. The CPU 1510SP-1 PN supports operation as an IO
controller, I-device or standalone CPU.
With its optional PROFIBUS interface, CM DP, CPU 1510SP-1 PN supports the
configuration of PROFIBUS networks in addition to PROFINET IO. When you use the
interface as a PROFIBUS DP interface, you can configure the CPU 1510SP-1 PN as a DP
master or as an intelligent DP slave (I-slave).
IO controller
CPU 1510SP-1 PN sends and receives data from the connected IO devices within a
PROFINET IO system. You can operate the CPU with up to 64 connected IO devices.
I-device
The "I-device" (intelligent IO device) functionality allows you to exchange data with an IO
controller. CPU 1510SP-1 PN thus fulfills the role of an intelligent distributed pre-processing
unit for sub-processes. The I-device is connected as an IO device to a higher-level IO
controller for this purpose.
Advantages:
●Interference-resistant configuration due to short signal and encoder wiring
●Reduced wiring requirements for transmission of the data via PROFINET
Standalone CPU
You can also use the CPU 1510SP-1 PN in the ET 200SP distributed I/O system as a
"central system" without a higher-level controller.
DP master
To use the ET 200SP as a DP master, you need the CPU and the optional communication
module, CM DP. When used as a DP master, ET 200SP exchanges data with the connected
DP slaves via PROFIBUS DP.

Product overview
2.2 Properties
CPU 1510SP F-1 PN (6ES7510-1SJ00-0AB0)
Manual, 12/2014, A5E35264953-AA 9
Intelligent DP slave (I-slave)
To use the ET 200SP as an intelligent DP slave (I-slave), you need the CPU and the optional
communication module, CM DP. As an I-slave, ET 200SP is connected via PROFIBUS DP
to the higher-level DP master and exchanges data with it.
2.2
Properties
Article number
6ES7510-1SJ00-0AB0
View of the module
The following figure shows the CPU 1510SP F-1 PN.
Figure 2-1 CPU 1510SP F-1 PN

Product overview
2.2 Properties
CPU 1510SP F-1 PN (6ES7510-1SJ00-0AB0)
10 Manual, 12/2014, A5E35264953-AA
Properties
The CPU 1510SP F-1 PN has the following technical properties:
●Communication:
–Interfaces
The CPU 1510SP F-1 PN has a PROFINET interface (X1) with an integrated 3-port
switch. Port 1 and port 2 are located on the pluggable BusAdapter. Port 3 is integrated
in the housing of the CPU. The CPU supports the BusAdapters BA 2xRJ45 and
BA 2xFC. You connect the PROFINET IO to the CPU via the BusAdapter. Port 1 and
port 2 can also be used as ring ports for the configuration of redundant ring structures
in Ethernet (media redundancy).
Note
The CPU is delivered without a BusAdapter. You can find the article numbers of
the
supported BusAdapters in the "Accessories/spare parts" section of the ET
200SP
Distributed I/O system
(
http://support.automation.siemens.com/WW/view/en/58649293) system manual.
The PROFINET interface supports PROFINET IO RT (Realtime) and IRT
(Isochronous Realtime) in addition to PROFINET basic functionality. PROFINET IO
communication or real-time settings can be configured on the interface.
The CM DP is optionally available with a PROFIBUS interface (X2). You can find more
information about this expansion module in the manual CM DP communication
module (http://support.automation.siemens.com/WW/view/en/90156526).
You can find information about connecting the PROFINET IO BusAdapter to the CPU
as well as connecting the optional PROFIBUS interface to the interface module in the
system manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
●Integrated Web server:
The CPU is accessible via an integrated Web server for diagnostic purposes. You can
read the following information with the Web server:
–Start page with general CPU information
–Identification information
–Contents of the diagnostics buffer
–Querying module information
–Alarms (without acknowledgment option)
–Information about communication
–PROFINET topology
–Tag status
–Watch tables
–Memory usage
–Data logs (if used)