Siemens Simatic S7-1500 Technical Document

Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
SIMATIC
S7-1500/ET 200MP
Digital output module
DQ 16x230VAC/1A ST Triac
(6ES7522-5FH00-0AB0)
Equipment Manual
12/2021
A5E34934069
-AC
Preface
Documentation guide
1
Product overview
2
Wiring
3
Parameters/address space
4
Diagnostic alarms
5
Technical specifications
6
Dimensional drawing
A
Parameter data records
B

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E34934069-AC
Ⓟ
11/2021 Subject to change
Copyright © Siemens AG 2015 - 2021.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
Equipment Manual, 12/2021, A5E34934069-AC 3
Preface
Purpose of the documentation
This manual supplements the system manual S7-1500/ET 200MP
(https://support.industry.siemens.com/cs/ww/en/view/59191792).
Functions that relate in general to the systems are described in this system manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the systems.
Changes compared to previous version
Compared to the previous version, this manual contains the following change:
The module features a switching cycle counter as of firmware version V1.2.0.
Conventions
CPU: The term "CPU" is used in this manual both for the CPUs of the S7-1500 automation
system and for interface modules of the ET 200MP distributed I/O system.
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on
the handling of the product or on the section of the documentation to which particular
attention should be paid.

Preface
Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
4Equipment Manual, 12/2021, A5E34934069-AC
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (https://www.siemens.com/industrialsecurity).
Open Source Software
Open-source software is used in the firmware of the I/O modules. Open Source Software is
provided free of charge. We are liable for the product described, including the open-source
software contained in it, pursuant to the conditions applicable to the product. Siemens
accepts no liability for the use of the open source software over and above the intended
program sequence, or for any faults caused by modifications to the software.
For legal reasons, we are obliged to publish the original text of the license conditions and
copyright notices. Please read the information relating to this on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109741045).

Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
Equipment Manual, 12/2021, A5E34934069-AC 5
Table of contents
Preface ................................................................................................................................................... 3
1 Documentation guide ............................................................................................................................ 6
2 Product overview................................................................................................................................... 8
2.1 Properties ............................................................................................................................ 8
2.2 Functions .......................................................................................................................... 10
2.2.1 Switching cycle counter ..................................................................................................... 10
3 Wiring .................................................................................................................................................. 12
4 Parameters/address space ................................................................................................................... 13
4.1 Parameters ........................................................................................................................ 13
4.2 Declaration of parameters.................................................................................................. 14
4.3 Address space.................................................................................................................... 15
5 Diagnostic alarms ................................................................................................................................ 20
5.1 Status and error displays .................................................................................................... 20
5.2 Diagnostics alarms............................................................................................................. 22
6 Technical specifications....................................................................................................................... 23
A Dimensional drawing........................................................................................................................... 27
B Parameter data records ....................................................................................................................... 29
B.1 Parameter assignment and structure of the parameter data records.................................... 29

Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
6Equipment Manual, 12/2021, A5E34934069-AC
Documentation guide
1
The documentation for the SIMATIC S7-1500 automation system and the SIMATIC ET 200MP
distributed I/O system is arranged into three areas.
This arrangement enables you to access the specific content you require.
Basic information
The System Manual and Getting Started describe in detail the configuration, installation,
wiring and commissioning of the SIMATIC S7-1500 and ET 200MP systems. The STEP 7 online
help supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
S7-1500 and ET 200MP systems, e.g. diagnostics, communication, motion control,
Web server, OPC UA.
You can download the documentation free of charge from the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109742691).
Changes and supplements to the manuals are documented in a Product Information.
You can download the product information free of charge from the Internet
(https://support.industry.siemens.com/cs/us/en/view/68052815).

Documentation guide
Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
Equipment Manual, 12/2021, A5E34934069-AC 7
Manual Collection S7-1500/ET 200MP
The Manual Collection contains the complete documentation on the SIMATIC S7-1500
automation system and the ET 200MP distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/86140384).
SIMATIC S7-1500 comparison list for programming languages
The comparison list contains an overview of which instructions and functions you can use for
which controller families.
You can find the comparison list on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/86630375).
"mySupport"
With "mySupport", your personal workspace, you make the best out of your Industry Online
Support.
In "mySupport", you can save filters, favorites and tags, request CAx data and compile your
personal library in the Documentation area. In addition, your data is already filled out in
support requests and you can get an overview of your current requests at any time.
You must register once to use the full functionality of "mySupport".
You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en).
Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus on individual products.
You will find the application examples on the Internet
(https://support.industry.siemens.com/cs/ww/en/ps/ae).

Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
8Equipment Manual, 12/2021, A5E34934069-AC
Product overview
2
2.1 Properties
Article number
6ES7522-5FH00-0AB0
View of the module
Figure 2-1 View of the DQ 16x230VAC/1A ST module
Properties
The module has the following technical properties:
•16 digital outputs (Triac)
•Rated output voltage 120 V/230 V AC
•Rated output current 1A (per channel)
•Configurable substitute values (per channel)
•Suitable for solenoid valves, DC contactors, indicator lights and smaller single phase drives
•Switching cycle counter for connected actuators, e.g. solenoid valves

Product overview
2.1 Properties
Digital output module DQ 16x230VAC/1A ST Triac (6ES7522-5FH00-0AB0)
Equipment Manual, 12/2021, A5E34934069-AC 9
The module supports the following functions:
Table 2- 1 Version dependencies of the module functions
Function Firmware ver-
sion of the
module
Configuration software
STEP 7
as of V13 SP1 with
HSP 0119
GSD file in
STEP 7 , V12 or higher
STEP 7 V5.5 SP3 or higher
Firmware update
V1.0.0 or high-
er
X
--- / X
Identification data I&M0 to I&M3
V1.0.0 or high-
er
X
--- / X
Parameter assignment in RUN
V1.0.0 or high-
er
X
X
Module-internal Shared Output (MSO)
V1.0.0 or high-
er
X
(PROFINET IO only)
X
(PROFINET IO only)
Configurable submodules/submodules for
shared device V1.0.0 or high- er X
(PROFINET IO only)
X
(PROFINET IO only)
Switching cycle counter V1.2.0 or high-
er V16, Update 4 or higher with HSP 0343 or
V17 or higher with HSP
0343
(PROFINET IO only, central
operation with a S7-
1500 CPU is supported)
X
(PROFINET IO only)
You can configure the module with STEP 7 (TIA Portal) and with a GSD file.
Accessories
The following components are supplied with the module and can also be ordered separately
as spare parts:
•Labeling strips
•U connector
•Universal front door
Other components
The following component can be ordered separately:
Front connectors, including potential jumpers and cable ties
For more information on accessories, refer to the S7-1500, ET 200MP system manual
(https://support.industry.siemens.com/cs/ww/en/view/59191792).