SIFENE SIF-10011 User manual

Centrifugal Juicer
U ser Manual
SIF-10011
Facebook: @sifenefans
Message: @sifenefans
Email:[email protected]

Contents
C hapter 1 P recau tion s for safe use
C hapter 2 P arts an d th eir fun ctio ns
C hapter 3 D irections for use
C hapter 4 M ainten ance
C hapter 5 Safety in dexes
C hapter 6 F ault an alysis an d elim in atio n
Foreword
Thank you for using our juicer. F or correct use and m aintenance of the product, we have specially
com piled this U ser’s M anual. Please read it carefully before using the product and keep it for future
reference.
This U ser’s M anual is suitable for our SIF-10011 juicers only. We reserve the right of final interpretation
of it. All contents herein are your reference for use and m aintenance only. P lease consult our customer
service department about matters not mentioned herein and give us your valuable criticism s and
suggestions. We hope to m ake your life warm, convenient and healthy through our products.
Chapter 1: Precautions for safe use
1. M ake sure the product has an input voltage of AC 120V～60H z before use.
2. D isconnect the power supply before dismantling, assemblin g or adjusting any part.
3. The product has Y type connection. If the power cable is damaged, contact our custom er service
department or have it replaced by a designated service center directly.
4. Before use, check whether any parts such as the power cable or the plug is dam aged and, if it is,
stop using the product and contact our customer service department prom ptly.
5. If product m aintenance is necessary after use, contact our customer service departm ent or have the
maintenance done by a designated service center directly. It is dangerous to dism antle the product
by yourself.
6. Before connecting the power supply, m ake sure the detachable parts such as the juice strainer and
the top cover are all properly installed.
7. When the product is running, never put hands or sharp articles into its feed opening, replace the
pushing rod with any object, or have eyes close to the feed opening as this m ay cause accidents to
happen.
8. Keep the juice strainer and m otor wheels away from the operator’s body and other hard foreign
objects when the product is running to avoid personal injuries and product dam age.

9. After juicing, do not dismantle the detachable parts of the product until the motor and the juice
strainer have both stopped and the power supply has been disconnected.
10. Operate with the rated operating tim e strictly: Juice continually for 1 minute each tim e, at m ost.
After ending any function above, stop for 2 m inutes to end a cycle. Stop for 15 to 20 m inutes after
3 successive cycles and start again after the motor has cooled down. This practice can prolong life
of the product.
11. If the product stops running while in use, it is possibly caused by the temperature protection of the
motor. D isconnect the power supply for cooling and use the product 15 to 20 minutes later.
12. To avoid deformation and damage caused by heat, do not disinfect any accessories in hot water
above 80℃or m icrowave ovens. Parts of the juicer in contact with food m aterials should be clean,
hygienic, reliable and in compliance with relevant food hygiene certification.
13. D o not place main unit of the product into water or other liquids, or flush out with water or other
liquids (it can be wiped with a soft cloth).
14. D o not clean the product with steel wool, abrasive cleansers, or corrosive liquids (such as gasolin e
or acetone).
15. Put the product in a place out of reach of children. U se or play of the product by persons with
disabled lim bs, sensory or m ental disorders, or by persons without relevant experience or
knowledge (including children) is forbidden.
16. D o not process any fruits or vegetables with cores, hard seeds, shells, or thick skins until their cores,
hard seeds, shells, or thick skins have been removed.
17. This product is suitable for individuals and/ or families only.
Chapter 2: Parts and their functions
12

N o . P art F un ction
1 Pushing rod
F or gen tly pushing the food materials in food m aterial feeding to ensure full
contact between the food m aterials and the juice strainer and improve
juicing efficiency.
2 Top cover F or con nectin g with th e m ain unit. As a key part for juicing an d safety
protection.
3 Juice strainer F or cutting food m aterials by the cutter holder at its bottom , filtering juice,
and separating fruit residue by the lateral strainer.
M iddle ring
F or discharging the juice separated by the juice strainer by means of pressin g.
Juice cup cove Put cover on the juice cup to keep foreign bodies out when accepting juice.
To separate the fruit juice from foam .
A container for accepting juice; easy for cleaning.
F or con trolling the operating status (including inching, low speed, an d h igh
speed) of the product.
As the m ain part of the product, it contains parts such as the m otor and
serves as the power source of the product.
Baffle
Juice cup
K nob switch
M ain unit
Pull rod
A key com pon ent for starting the safety switch and locking the body an d
header to allow the m achine under normal working condition.
4
5
6
7
8
9
10
11 F ruit
cup reside F or co llecting the fruit residue separated by th e juice strainer by m eans of
pressing.
G ears
0: F or closin g and stop ping
Inching: Inching
1: A lo w- speed gear for processing soft fruits and vegetable
Chapter 3: D irections for use
C lean the p arts in co ntact with food m aterials thoroughly before using the product for the first time
(see th e con tent of “ C hap ter 4 M aintenance” ).
s
such as waterm elons, tomatoes, cucumbers and
strawberries.
2: A h igh- speed gear for processing all fruits and vegetables
(see “II. Tips for fruit selection” under “D irections for use”
for the selection of fruits, vegetables and gears)
I. U se of product
The product is designed with a dual- action safety system and can run after all parts are correctly
installed. Install and use the product following the steps below.

1 Install middle ring on th e body. P roper installation is required.
2
Put the juice strainer into the m iddle ring and properly install it on the
motor wheel (before use, check whether the juice strainer is dam aged
and, if it is, do not use the product and contact a designated service
center).
3 Install the pom ace cup.
4 Put the header right above on the body and properly install it as per
the direction indicated on the header.
5 Put the pulling rod inside the two grooves of the header until
com pletely in place or the product will not work norm ally.
6 Allow the fruit juice cup baffle to slide in the juice cup along th e neck.
Put on the cup cover.
7 Put juice cup under the outlet.
8 Align the groove of the pushing rod with the flange inside the feedin g
port and put the pushing rod inside the feedin g port.
9 C onnect the power supply. (M ake sure the switch is off before
connecting the power supply).
10
C lean fru its and vegetables and cut them into blocks suitable for the
food material inlet (remove hard seeds, shells, or thick skins of the
fruits and vegetables, if any, first).
11 Activate the switch, start working with working time ≤1min.
12 Put the prepared fruit and vegetables in the feeding port.

13
Push the blocks of fruit and vegetables gently through the feeding port
with the pushing rod. Too m uch excessive force will affect the juicing
efficiency.
(N ever put your fingers or other objects inside th e feeding port!
D isconnect the power and clean the pomace cup when the pomace or
juice cup is filled.)
14
When there is no longer juice flowing via the juice outlet after good
material processing, turn the switch off, disconnect th e power supply
and take the juice cup from the juice nozzle after the m otor and the
juice strainer have both stopped running (drink the juice soon,
otherwise its taste and nutrition will bo th be in fluenced after som e
tim e from exposure to air).
15
Take the juice cup away from the outlet nozzle when the m otor and
juicing screen has completely stopped.
The foam baffle attached to the juice cup m ay help you obtain a cup
of foam less juice. The baffle may be neglected if juice with foam is
required.
Chapter 4: Maintenance
1 Turn the power switch off before cleaning the product.
2 Clean the product promptly after use.
3
Exterior of m ain unit of the product m ay be wiped with a wet cloth. D o not
place the m ain un it of the product into water or other liquids, or flush out with
water or other liquids.
4 Store the product in a dry place without direct ultraviolet rays.
5 M ake sure the product is clean and dry before storing it.
6 Clean the detachable parts followin g the steps below.
1 Take out the pushing rod.
2 Pull open the pull rod from right direction and take off the header.

3 Remove the juice strainer and the middle ring in order.
4 With water, clean the pom ace cup, m iddle ring, juicing screen, and juice cup
successively.
Chapter 5: Safety indexes
As a class II electric appliance, this product needs no groundin g device.
Chapter 6: Fault analysis and elimination
F ault P ossible cause E lim in ation
After the power supply is
connected and the switch
is turned on, the product
does not run.
1. The m iddle ring is not
correctly installed.
2. The top cover is not
correctly installed.
3 The top cover contact has
fractured.
1. Install the m iddle ring correctly.
2. Install the top cover correctly.
3. R eplace the top cover.
There is a bad sm ell from
the motor the first few
tim es using the product.
It is normal.
If the bad smell still exists after the product has been
used several tim es, have the product tested by a
designated service center.
Rated voltage 120V~
Rated power 500W
Rated frequency 60H z
Continual juicing tim e ≤1 min.
Time interval ≥2 min.

The product stops
autom atically while in use.
1. The voltage is too low.
2. There are too m any food
materials in the product.
3. The pushing was rod is
pushed too violently.
4. The m otor is under
temperature protection.
1. Check wh ether the voltage is too low.
2. D isconnect the power supply and rem ove the surplus
food m aterials.
3. G ently push the pushing rod.
4. Stop the product and start it again 20 to 30 m inutes
later.
There is a lot of residue in
the juice.
1. The juice strainer is
damaged.
2. There is a lot of residue in
the m iddle ring.
1. R eplace the juice strainer.
2. C lean the m iddle ring.
The product has abnormal
vibration or big noise.
1. The juice strainer is not
correctly installed, resulting in
poor running balance.
2. The product is not steadily
placed or the foot pad has
fallen off.
3. The voltage is too high; or
4. There are m any food
materials in the product.
1. Install the juice strainer correctly.
2. P lace the product steadily or install the foot pad
correctly.
3. Check wh ether the voltage is too high.
4. D isconnect the power supply and rem ove the surplus
food m aterials.
There is very little juice.
1. There is a lot of residue in
the middle rin g.
2. The pushing rod was
pushed too violently.
1. Clean the m iddle ring.
2. G ently push the pushing rod.
The cutter holder is
seized.
The cutter holder is wound or
seized by food m aterials.
D isconnect the power supply, take out the food
materials and cut them into sm aller blocks.
N otes:
The table above introduces the com mon faults and their cause analysis and elimination m ethods. F or
other faults, contact our custom er service department or have the product repaired by a designated
service center directly. D o not dism antle or repair the product by yourself.
Facebook: @sifenefans
Message: @sifenefans
Email:[email protected]